Replaces
2 Piece Control Arm with Ball Joint Set
$139.95
6 Piece Steering & Suspension Kit
$144.95
8 Piece Steering & Suspension Kit
$154.95
10 Piece Steering & Suspension Kit
$156.95
10 Piece Steering & Suspension Kit
$157.95
8 Piece Steering, Suspension, & Drivetrain Kit
$209.95
12 Piece Steering & Suspension Kit
$349.95
16 Piece Steering, Suspension, & Drivetrain Kit
$364.95
16 Piece Steering, Suspension, & Drivetrain Kit
$449.95
Part Details
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a front sway bar link on a 2006 Chevy Impala. It's the same for model years 2000 through 2012, and the procedure is exactly the same on the left side, and on the right side. To perform this repair, you'll need a 13, 14, and 19 millimeter sockets and socket wrench; 13 and 14 millimeter wrenches; some penetrating oil; a hammer; flat blade screwdriver; and a jack and jack stands.
Start by loosening the five plastic lug nut covers that hold the wheel cover to the wheel. For taking off the wheel, you'll be using that same 19 millimeter socket, but if you don't have the benefit of a lift or air tools, start with it on the ground. Loosen up your five lug nuts slightly. Get it safely on some jack stands and then proceed to remove the five lug nuts with your socket, socket wrench and breaker bar. Then take off your tire. I
'm going to turn the steering knuckle there a little bit so you can get a good look at the sway bar link, which is between the control arm and the sway bar. I'm using a 13 millimeter socket and socket wrench, on the bottom, and then I'm counter holding it with a 13 millimeter wrench up top, and I'm going to go ahead and fast forward as I loosen those up. The bolt that goes through the center there is quite corroded and sticking to the rubber bushing, so I'm going to use some penetrating oil. I'm going to try and separate the bushings and those washers, as well as the bolt that goes through the control arm, all the bushings, and the sway bar, using a flat, long screwdriver to try and get some room, and start to pull that away. Once I do, I can just use a hammer on the top and tap it out. As you pull everything out, you'll just want to remember the position of everything, how the bushings and the washers go in.
Here you'll see the old part, rusted and corroded, and the new part from 1A Auto. That, there, is how it will go back into the car. I'm going to start with a rubber bushing against the control arm and then a washer. On top of the washer I'm going to place the metal sleeve. I'm going to use the pry bar to lift up so that I can get, then, another rubber bushing, place it on top of the sleeve with a washer underneath it. As I lift it up then I can let it down and it'll fall right into place. I've got the bolt going from the bottom with a rubber bushing. It's got the bolt, then a washer and then the rubber bushing that's going to be sitting next to or against the control arm. You can see there. You might have to twist or pull some of the stuff to get it to line up so it goes through. Again, here, I'm using a hammer. I'm going to use the pry bar again to pry up on that sway bar to give me a little bit more room. Then once I get that pushed through, I'm going to put another rubber bushing and a washer, and then the nut. Then, to summarize, from the bottom up, you've got the bolt, washer, rubber bushing, control arm, rubber bushing, washer, sleeve, washer, rubber bushing, then the top of the sway bar, then a rubber bushing, a washer, and then the nut. I'll go ahead and fast forward as I use a 14mm wrench and a 14 millimeter socket and socket wrench to tighten up the sway bar link.
I'm reinstalling the wheel and I'm going to tighten by hand the five lug nuts. Then, once I do that, I'm going to tighten them back up with the impact wrench, and then as I get the car down, I'm going to use a 19 millimeter socket with a torque wrench, and torque all five lug nuts in a star pattern to 100 foot-pounds. Then, go ahead and reinstall your hub cab, lining up the notch in the hub cap with the valve stem, and then go ahead and tighten up those plastic lug nut covers
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a lower control arm on this 2003 Chevy Monte Carlo. We'd show you on the passenger side, but it's the same procedure on the driver side. The items you'll need for this include a new lower control arm from 1AAuto.com, 13mm, 14mm, 18mm, 19mm and 21mm socket and ratchet, T55 Torx bit, 14mm, 19mm, and 21 mm wrenches, pliers, flat blade screwdriver, hammer, ball joint fork, and Jack and Jack stands.
Start off by just loosening up these lug nut caps. Now, you can remove your lug nut. If you don't have air-powered tools, you want to loosen these up while the vehicle is on the ground, then raise the vehicle, and remove them the rest of the way. If you do have air-powered tools, you can just remove them right here, and you can just pull your wheel off.
Spray your sway bar link with some penetrating fluid to make it easier to remove. And then, using a 14 mm wrench and socket and ratchet, just remove the nut on top of the sway bar link. That actually comes apart easily. It's not uncommon, but sometimes the link is totally broken, and you don't even have to do this step. You just pull the remains out. Also, sometimes, they're frozen up so bad, you have to use a sawzall or a torch to cut the links out.Pull the top bushings off and push the sway bar link down and out, and then remove the bushings in the center.
Replace a couple of lug nuts to hold the rotor in place. Using a pair of pliers, remove this cotter pin at the top of your ball joint. Now, jack up underneath the wheel. Using a 19mm wrench and a hammer, just loosen up this castle nut. You want to loosen it until it's only on by a few threads. Now, hammer the knuckle, and the ball joint should loosen up, and you should be able to pull it down.
If this isn't the case, you're going to need a ball joint splitter or a ball joint fork and just hammer it in between the knuckle and the ball joint to separate them. Now, remove that nut the rest of the way, and then lower the jack. Next, you want to remove these two 21mm nuts. The bolt is actually a T57 head, which is a fairly rare tool. We actually get by using a T55 with two people. Just make sure you hold that T55 Torx bit in there well, and you can do it.
For this bolt, you want to use a 19mm socket and ratchet and a 21mm wrench to remove it. Now, pull those two bolts free, and then you can pull the control arm down and over. Then just pull out this last corner, you will have to maneuver it a little bit, it's in there pretty good usually. That will pull out, and then the control arm is free.
On the left is the old lower control arm; on the right is the new one from 1A Auto. You can see they're identical, and they'll fit exactly the same. Take your lower control arm and push in the ball joint side first, then curve it back and push in this side. Now, you want to turn this so that the hole through the bolt is on the side so you can get your cotter pin back through it. You want to just angle the ball joint up into the knuckle. You may have to move the knuckle a little bit. Once you have it pushed into place, replace that castle nut, line up the holes right here on the control arm, and push your bolt through. Jack up the knuckle and tighten that castle nut a little bit more.
Once you get it at an angle that you can get the bolt up through the ball joint, just push the bolt through. Hammer the other bolt through and replace the nuts on both. Tighten up that castle nut. Push your cotter pin through and bend the tabs in opposite directions. Be sure to bend it in a way that the cotter pin ends don't have a change of going up and scraping along the CV joint boot.
Now, tighten up this bolt, and tighten this bolt. Take your sway bar link and put the center bushings in first, and then run your sway bar link up through the bushings. Replace the top bushing and the washer and nut, and just twist that nut on. Once you have it on there securely, you want to lower your vehicle down on to the jack stands so that all the pressure is on the suspension, and then tighten up the sway bar the rest of the way.
Replace your wheel and each of the lug nuts. You want to just tighten them preliminarily, then lower the vehicle, and tighten them the rest of the way.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
