Replaces
Part Details
Product Features
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace as well as service the bulb in a side marker light on this 1996 Chevy Tahoe. We show you in the passenger side, but the driver side is the same procedure. The items you'll need for this include a new side marker light from 1AAuto.com, a Phillips screwdriver and a 13mm socket and ratchet.
Start off by removing these four Phillips screws. We'll just fast-forward as Don does this. Once those removed, pull the light out, and you just twist the sockets counterclockwise to remove them.
Now to service the bulb on your side marker light. You just twist the socket out and the bulb pulls straight out. You push your new one in, and then the socket twist back into the side marker light.
To change the assembly, you want to remove these two 13mm nuts, so just twist out that socket and remove those two nuts. We'll just fast-forward here as Don does this. Once those are removed, the side marker light will pull right out.
On the left is the old side marker light; on the right is the new one from 1A Auto. You can see they're identical, and they'll mount exactly the same.
Push your new side marker light into place and replace those two 13mm nuts. Then twist your socket back into place.
Now take your parking light and twist those two parking light sockets into place by just twisting them clockwise to lock them. Then push your parking light assembly into place. Make sure all four of those holes line up, and replace those four Phillips screws. Then you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to service the headlight bulbs as well as replace the entire headlight assembly on this 1996 Chevy Tahoe. We show you on the passenger side, but the driver side is the same procedure. The items you'll need for this include new headlights from 1AAuto.com, Phillips screwdriver, and a 7mm and 10mm socket and ratchet with an extension.
You want to first remove these four Phillips screws, and we'll just fast-forward as Don does this. Pull the light out, twist the sockets counterclockwise, and pull them out. Then, you want to twist this socket out of your side marker light, and then repeat the process on the other side.
Next, you want to remove this series of 7mm bolts, and we'll just fast-forward as Don does this. There's one more 7mm bolt right here. Once those are removed, you want to just lift up this tab, pull the grille forward, and there's another one on the other side. There's another clip right in the center. Using a stick or a long screwdriver, you just want to push that tab and then pull out on that center tab. Just to give you a better look at it, it's this tab right here.
Next, you want to remove these four 10mm bolts that secure your headlight, and we'll just fast-forward as Don removes those. Now, to service your bulbs, both of them are the same. You just pull back this tab and pull the harness free, then twist the bulb out. Push the new one in, twist it clockwise to lock it, and then just reconnect your harness. If you're looking to replace the whole assembly, you just want to disconnect both of these harnesses by pulling up that tab.
Then take your new headlight and push the harnesses into place. Then push your headlight back into place and replace those four 10mm bolts. Once those are in place, take your grille and pull your parking light sockets through, and then you want to line up the tabs on the grille.
The first one you want to do is the center one, and just push down that tab and push the tab on the grilled into place until it locks. Now, line up those side ones and push those into place and we'll just fast-forward here as Don replaces those five 7mm bolts. There's four along the top of the grille, and then that one in the center just above the badge.
Now, twist your side marker light back into place. Then twist your two parking light sockets back into place, just turning them clockwise to lock them. Then push the assembly into place and replace those four Philip screws. Repeat the process on the other side.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the grille on this 1996 Chevy Tahoe. It's the same part and process on these Tahoes from '95 to 2000. The items you'll need for this are a new grille from 1AAuto.com, Phillips screwdriver, 7mm and 13mm socket and ratchet with an extension, and flat blade screwdriver.
You want to first remove these four Phillips screws. We'll just fast forward as Don does this. Pull the light out and twist these sockets counterclockwise and pull them out. Then you want to twist this socket out of your side marker light. Then repeat the process on the other side.
Next, you want to remove this series of 7mm bolts. We'll just fast forward as Don does this. There's one more 7mm bolt right here. Once those are removed, you want to just lift up this tab and pull the grille forward and there's another one on the other side. There's another clip right in the center, using a stick or a long screwdriver, you just want to push that tab and then pull out on that center tab. Just to give you a better look at it, it's this tab right here.
Up top, is the old grille; below it, are the two from 1A Auto. In the middle is an exact replacement of the old grille and on the bottom is an all chrome version, which we'll be installing on this truck, but first we have to swap over all the stuff from the old grille. You just want to remove these ten 13mm nuts. We'll just fast forward as Don does this. You also want to swap over these clips and there are eight of them in total, four on one side, and four on the other. To remove them, all you do is push in those four triangular pieces, and it just pops out and if gives you any trouble, you can use a flat blade screwdriver to help push it through. We'll fast forward as Don takes the new grille and starts attaching those side marker reflectors and the side marker lights and replacing those 13mm nuts. For the badge, just push it into the center and, just like with the lights, replace those two 13mm nuts. Now, take those eight clips and just push them into place.
Once those are in place, take your grille and pull your parking light sockets through. Then, you want to line up the tabs on the grille, and the first one you want to do is the center one and just push down that tab and push the tab on the grille into place until it locks. Now, line up those side ones and push those into place. We'll just fast forward here as Don replaces those five 7mm bolts. There's four along the top of the grille and then that one in the center just above the badge.
Now, twist your side marker light back into place and then twist your two parking light sockets back into place, just turning them clockwise to lock them. Then push the assembly into place and replace those four Phillips screws. Just repeat the process on the other side.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
