Replaces
Part Details
Product Features
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
This video is brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet.
This video details headlight replacement on a 98-2002 Dodge Ram truck. From the video you will see that this is an easy process. This is also how you would access the headlight bulb for replacement.
How you doing? I'm Mike Green. Today we're going to replace headlights on a 1998-2002 Dodge pickup. What we have here is the sport model. The headlight procedure for sport model and the regular model is the same. This procedure takes ten minutes; it's quite an easy procedure. Tools you'll need: a couple of rags to help protect your paint, a clip tool or I have a chisel and I'll use the rags and chisel together to get some of the clips off, a ten millimeter wrench and a ten millimeter socket with an extension and ratchet.
First using your clip tool or something to pry and the rag to protect the paint, you remove these three clips holding this gasket. Next remove your parking light by removing the little screw from underneath here, Phillips. After that screw is removed you can firmly comes out and unhook the bulb. Now you have three bolts to take out. One here at the front, one down here, this one you can either reach from the top here or you can reach down from underneath and one here on the side. You may want to cover your bumper cover, just to keep anything from getting scratched.
Okay now that you removed the bolts put the rags on to protect your cover. There's a small pin in here that's still holding a light. You can use something to pry on it and give it a good quick pry and then you want to move out and tilt the light forward while not letting the pin get stuck. You kind of want to pull outside of the truck and at the same time try to rotate the light forward. Now you can see your headlight connection and move your low beam and your high beam and the light comes right out. Okay insert the new light by kind of going upside down against the fender and rotating it on. Put your finger here to make sure this doesn't contact your paint and then pull the front out while you slide it on and push that under.
Okay, so now it's kind of in place. You reach in behind and connect your low beam, reach in behind and connect your high beam. There's a locating pin over here that you want to get in first, and now you can make sure this pin is here and that initial pin holds it in place. At this point you can push these pins back in and now you put your three bolts back in.
Now we've got the headlight in, we've got the three mounting bolts tight. It clips on. Now we're just going to install the parking light, plug in the lamp. Again make sure this clip's in, and this lower clip's in while the locating pin goes into to the hole, and just give it a good tap. A good push, plug it in. Now finally put in the screw to secure it. Now your left side's done.
This video was brought to you by the folks at www.1AAuto.com. All the parts in this video are available on their website. We hope you enjoyed this and we hope it helps you with your project. Thank you.
