Replaces
TRQ side mirrors and mirror components are designed to match the function, fixture, and performance of the original version for easy installation. TRQ mirrors are DOT certified, comply with all federal safety standards, and are independently lab tested to ensure our products comply with all government regulations. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Exact fit - To obtain proper fit and function confirm your vehicle has the exact mirror options listed.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly. That's going to save you time and money. Thank you and enjoy the video.
In this video, we're going to show you how to replace a side view mirror on this 2004 Dodge Ram, same for most '02 to '08. This is in case your mirror got into a little altercation with maybe a garage pole or a garage door or a baseball or something like that. Tools you'll need are a T40 torx driver, a Phillips screwdriver, a flat-blade screwdriver, and a 10-mm wrench or a socket and ratchet.
To remove your front door panel, you're going to start by removing a T40 torx screw and hold your handle on, right there. Okay, and then, you're going to remove four Phillips screws, one there, one up here, and then two down in the lower part of your door panel. This is a my T40 torx driver.
Okay, I'm going to speed it up here, take that t30 screw out and then your handle comes off, and then, I'm going to start with the Phillips screwdriver, take those two off, and then slyly take my jacket so you can see my 1A Auto sweatshirt, and remove the two lower Phillips screws.
Now use a regular screwdriver. Carefully pry up on your switch plate here. Okay, then pull it up and both these connectors, they have a little button right here. Press the button and work the connector and release the switch. Same thing here. This button right there. Okay, now you just lift the door panel up over the lock here and off.
To remove your mirror, or if your mirror's broken, what's remaining of your mirror, here is your harness lead. There's just a little button right on top. Push that down, unplug it. A 10-mm wrench, I happen to use just because these ones are a little bit long. Then, once you get them loose, they come right off by hand.
Okay, so we'll just fast forward through removing those three 10-mm nuts. The mirror has a couple of tabs. Just kind of pull them down. Okay, and here's just a quick close up. Use your screwdriver, pressing on each tab on each side and pull out the mirror at the same time. Push those tabs through and bring the mirror up and down.
Okay, so here we have our new replacement; I pulled one out, all comes right out of the box. It's shipped folded. Fold it back into place, and you can see, it's basically all the same as the original. It's going to mount the same. Same connector and everything. Looking outside, put it underneath my shield a little bit. Pop one in and then the bottom ones. Using my original fasteners. Okay, and we'll just fast forward through putting those three 10-mm nuts on and then tightening them up. You want to tighten them up, uh nice and firm but not too tight. You don't have to go crazy but good and firm. Poke it back in.
Okay, you can see everything works correctly. Take this off and put your door panel back on. Use this piece of insulation that fell off when we took our door panel off. Press that back on, and before you put the door panel back on, you want to take this lock bezel and push the clips in and pop it off. It just has a little teeth there. Okay, it just has a little teeth there that holds it in. So, you just kind of push them with your finger over.
Put it back on, what you want to do is, there's teeth at the bottom, kind of rest it like that and bring it up. Pull your harnesses up out of the way. Okay, lock your door, press your door lock down. Take that up and over and pull it back up. You might have to pull it up just a little bit and then slide it down. Then, okay put the four Phillips screws back in.
Okay, and we'll fast forward through just putting those four Phillips screws in and tightening them up. Okay, our switch. Put the smaller capture in and the larger capture and feed the wires down in. Push it down in. Our door handle. Just got to put my extension and my bit in. Put into place, and you should be able to just pretty much start turning. It pretty much finds its own way. For your lock, snap right down, and you're all set.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll free 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to install our upgraded power folding mirrors on this 2006 Dodge Ram. This truck does not have power folding mirrors. We're going to put the power folding mirrors on it and show you how to wire them. On this vehicle it also has the optional running lights as well as puddle lamps. We wire up all those things. You will be able to purchase the mirrors as you want maybe you just want the power fold, maybe you want the puddle lights, maybe you don't. We'll show you how to do each one of those. You'll need new mirrors from 1AAuto.com and a bunch of other pretty common tools. You will need wiring pliers and you'll need something to make the dead panel on your dash into a good place to mount the switch as you'll see later. We're going to show you in detail everything to do on the passenger side, but the driver side is the same procedure.
You want to remove the screw that's in behind the door handle, as well as couple of other screws: one up top and two down the bottom. With those screws removed, you can lift up on the panel and then just pop the lock bezel out and then reach up and through. I like to do it this way just to make sure you don't break that panel. You can push the clips, pop that panel up, and then there are tabs on those harnesses. Push the tabs in, remove the harnesses, and pull your panel up and off.
Four Philip screws hold the speaker, so remove those screws. Once you got the screws out, just pull the speaker out. On the back there is harness connection. There's just a little tab you press and pull that connection out. The harness has a little tab on the top. Push it down, disconnect the harness, and then remove the three 10mm nuts that hold the mirror in place. It's actually clips that hold the mirror even after the nuts are off they're on each side of the harness connection. You see here, we push them in as a helper holds the mirror and takes it off.
Okay, use a screwdriver to help yourself get under the door soleplate and then pull up, snap out. and then pull up to release the other clips that hold it in. You want to pull your glove box down so you can access behind it. There are just tabs on each side. You just push in on the sides of the glove box, pull it down, and it will unhook from the hinge. Now, you need to disconnect the body harness. There are basically four tabs around the harness. I'm actually pushing in on the tabs with the screwdriver and prying out at the same time. Then I reach in, I'm going behind it to push on the other final tab, pull that out, and then disconnect the harness by pushing down on the little tab and pulling it apart.
Okay, we're going to run our wires through the body harness connection. I'm going to reach in the door and just push the rubber boot through the door. Slowly and carefully pull your water shield down. Be very careful not to tear it or rip it, and you just need to pull the top corner down on each side.
On the driver side, you want to pull the side dash panel off. Work your fingers in and under the bottom and then slide them up and release the clips all the way around. We need to access the dome light harness. You want to remove this screw that holds the pillar trim in. Two screws on the bottom hold the lower dash panel in there and in behind that break controller. Once you have the screws out, pull out on that dash panel. You don't want to pull it down, you want to pull it mostly back and a little bit down to release all the clips.
Now, we're going to run one of our power fold harnesses across, and that will pull that harness through the rest of the way. Then feed it up into the dash and through the whole on the body of the truck. You want to repeat this process with the harness for the light as well. The folding harness has an insulation on it, and you basically have to put it through the body harness boot. You want to go back about 18 inches and cut it, and then cut about a foot of the insulation off back from there to the body of the car. I'm just going to fast-forward as I do that. We're actually not removing the insulation that's near the plug; we're removing an intermediate piece of the insulation.
Now, on the plug end, you want to pull the rubber boot off and then use a small flat blade screwdriver and there's a tab right inside to release that and pull the harnesses out. Now you can feed both your light harness and your power fold harness through. You could see I get the power fold harness through, and I pull that back insulation through to the point where I have just the bare wires. Then you get those wires, make sure they're placed in the corners of your harness connection. Once you get them pretty straight you can slide your harness back in and it's nice and tight and the wires are through.
Okay, here I'm using basically a straightened out coat hanger or you can use a piece of stiff wire. I'm feeding it through the boot and out the other end so I can hook it on to the wires and then pull the wires through the door hinge or the door Now with the wires through, I tape my wires on to it and then carefully pull it through that boot. Now, feed your wires into the door and very careful at this point, you need to make sure they come in into the door and then they exit out through this hole here. Make sure that they do not in any way interfere with the window regulator. You need to make sure that they're in behind the regulator and come up without interfering with the window. Both harnesses are routed up through the door, and make sure the harnesses come through the mirror pad.
Now we're going to hook those harnesses in as we put the mirror up the door. These are prototype mirrors that I'm fitting, so the harnesses were a little bit short so they had caused a little bit of difficulty. That won't be a problem on the production mirrors. With all the harnesses routed through correctly, put the three 10mm nuts back on and we'll tighten them up. Okay, you want to take the all black wire and hook it to a ground. Remove the end of it and put a wiring eye on it. Loosen up that 10mm bolt that's just below the mirror, and put the ground wire in there and tighten it back up. Now your door is all wired.
You're going to want to reach in and get the boot back in place. Pull it through the door through that speaker hole and get it back into the door. Then reconnect your harness. You have to pull the wires through on the other side just to make sure they don't kink it all and just work it in place. If you move the door around a little bit, it makes it a little easier to lock it in place. Make sure the boot is all back where it should be snapped in. Then just put on some wire ties to hold everything in place so it doesn't move around. Make sure you've cut those off and put the insulation back in place.
Here, we're just wire-tying the harnesses together using some, actually, electrical type. Tie them together, and then wire-tie them up into place so that they don't hang down at the passenger's feet. We have to hook the harness for the power fold to a switched power source. On this truck, once we opened up that side panel, there's an empty harness connection here. The orange wire is a switches power source. Just to make sure, you might want to just probe it with an electrical connector or an electrical probe. Just to make sure that it's only on when the power of the truck is on.
On our vehicle we had optional puddle lights on the other prototypes. We hook those puddle lights into the blue with green stripe wire that ran the dome lights. Here's a close up of using those fuse or the wire taps. Tuck in, and then we reconnect the dome harness after we had hooked the power source for those puddle lights up. Okay, just a test here. We'll turn the inside lights on and off. And you can see the puddle lights are lighting up.
And now just put that pillar trim back in place. Tighten up the screw that holds it. You'll need to ground the fold switch, so this wire is the one coming from the power folding switch harness. And we're just hooking it up to a screw at the bottom of the dash there. We've run our wires for both doors and the wire for the switch. Now we're going to mount our switch into this small panel, and we're going to be using a precision drill tool to fill out an exact hole for the switch.
Now just a test. Again, like I've said we've run the harnesses for both doors and the switch harness into the dash. And just a test . the mirrors fold and move back.
Now you have to run a wire out to the engine compartment of the vehicle. That's a power source for the marker lights. So we're going to run it right through the wiring boot. Seems like the best way to do it. And we're going to disconnect this harness it just seems like an easier way to get to things. Pull that back and disconnect that harness. So we use the same method that we used with the boots through the door. You put a piece of stiff wire up through that harness boot, hook it on to the wire, and pull the wire through to the engine compartment.
You can see here the wire is taped to a coat hanger, and we're pulling it back through into the vehicle. Now we're going to hook that wire to the parking light fuse, and we're kind of using an oldr style fuse tap. The new kit will come with a newer style fuse tap that create a separate circuit for the mirror lights. But the parking light fuse on the fuse box is right here, pull it out, put the tap in with it, and reconnect it. There's our wire hooked in, so put the fuse box cover back down.
Then, here we are just reconnecting a harness that we connected that made it easier to get the wiring through. Okay, again here using a wire tap and I'm hooking one of the lights, or actually the driver side marker light to that power wire we just ran from the fuse box. You can see I turn it on, a little test, and the marker light works, and so now I'm using another wire tap and connecting the wire for the other side. And the lights are LED so there's very little draw.
With all the wiring mostly complete, we've wire-tied everything into place to make sure it's nice and secure and it's not going to drop down on anybody's feet or get tangled or anything. Put the lower panel back into place and secure it with two bottom screws.Here we have our switch in that little panel, press the switch in, and put it into the dash.
Put the side panel back in place and any of the carpet trim on the sides. Hook your glove box back into place, and it just raises up and you put it back into place. And we've secured all the wiring with wire pads. And put the carpet and side trim back in place, Reconnect the main mirror harness. And reinstall the radio speaker, and we're going to fast-forward as we go through and putting the door panel back on. We showed you in detail on the passenger side, so you need to repeat everything we did on the driver side.
With everything back together we'll do a quick test. The power fold works nicely, and then the lights come on with the truck lights. And again our prototypes also had puddle lights. You may or may not have puddle lights on the mirrors that you purchase.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
