2007 Dodge Ram 2500 Truck Tailgate Handle TRQ DHA64589

Brought to you by 1AAuto.com. Your source for quality replacement parts and the best service on the Internet. In this video we're going to replace the tailgate handle on this 2004 Dodge Ram, the same as any 02-08.

Tools you'll need are a T30 Torx driver and an 8 mm socket. You'll also need a ratchet and an extension. You'll want to start out by removing a series of T30 Torx screws. You can see here I start with a hand wrench, but I quickly go to the air tools, a little faster and whether or not you have a bed liner, you can see here mine has a bed liner. If yours doesn't have the bed liner, you'll be able to see these screws, no problem. After we do these last ones, then we'll remove the bed liner piece and then there's two more screws underneath and then the tailgate access panel comes off and you can just flip it out of the way.

Now looking down here at the handle these clips, there's a little tab right here that you pry out and then pull the clip up and then the rod pulls right out. The same thing over here. Pry out, pull up, pull the rod out. Two 8 mm bolts. Okay, we'll speed it up here again and you'll notice as I start loosening the second bolt I reach under and just hold the handle up. There is your handle. Original handle, new handle from 1A Auto. Commonly what happens is these plastic parts break and that's usually because you need to lubricate your mechanisms. I'll show you how you do that. Obviously my original one is still fine on this truck, so I'm not going to waste a new one on it and I'll re-install the original. Before you put it back together you just want to lubricate the pivoting parts. Then also your latches here. Just for your information I'm using a little bit of spray on white lithium grease.

Re-installation, reverse the procedure. Put your handle up in. Kind of press it up in and shake it back and forth a little bit. Put your mechanism in. Two 8 mm bolts and nuts. When you put these rods back in you want to pull, you pull just gently towards you, not much. Just enough to make sure that there's no slack. Same thing, pull gentle towards the center of the truck. I'm going to speed up the rest of the way through it. If you have a bed liner, you probably put two or three bolts in first and then put the bed liner over the top of it and then what you want to do is you want to start all your bolts and I kind of violate my own rule here. I tighten up those two and then realize that I can't get one of them in; because, I need pull the bed liner around. Basically start all of your bolts first and then tighten them up afterwards.

We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll free 888-844-3393. We're the company that's with you on the Internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you to replace the tail gate handle on a Dodge Ram. This one is a 2008, but the procedure is pretty much the same for a 2002-2008. You'll need a new handle from 1AAuto.com, T-30 Torx driver, and an 8mm socket with a ratchet.

One very common problem with trucks is the tailgate being stuck in a closed position. The tail gate latch is often responsible for this. If your tail gate's stuck open, you can remove the inner skin. With the tail gate closed, release the latch and replace this fairly simply and restore your tail gate to proper operating conditions.

Remove the eight, T-30 Torx screws on the inside of the tail gate. We have a plastic tail gate cover. If your truck has one as well, you want to reach behind and pull the steel on the inner piece of the tailgate while you remove your plastic. Then remove the inner cover. The latch mechanism in the center here is operated when the latch is open. You press this down, it rotates this mechanism to pull the latch rod on either side and release the latches.

The latch itself can be broken. This mechanism can be snapped off. The plastic here can break or these latch rods can come out of their clips, meaning that you're only releasing one side of the tail gate. In any case, you can either manually turn this if your latch is broken, or you can pull in on the latch rods to release the tail gate and bring it down. Use an 8mm socket and ratchet to remove the two 8mm nuts on the back of the latch. Support the latch before releasing the nut fully. With the nuts removed, pull down on the bottom of the latch, slide it down, move it from the tailgate.

See our old part and our new part are exactly the same. The same size handle, the same size outer trim here. We have the same latch rod, same release mechanism there, this piece of plastic, new studs to mount into our latch in the actual tail gate.

See the old part's rotting out here. It will finish rotting out and breaking, wouldn't snap back into position, make for some awkward function of the tail gate or this piece of plastic here can get worn out from opening and closing the tailgate so many times, it stresses and snaps causing your tailgate to be stuck closed. If your old latch is rusted out and snapped and plastic is broken, this new part from 1AAuto is going to go in direct fit just like your original equipment and fix you up right.

Reinstall the handle into the tail gate. Be sure that the alignment pins on the latch handle are in their proper slots on either side. Once the pins are aligned, set your latch onto the studs to the back of your handle.

Reinstall the two 8mm nuts, tighten them down with a socket and ratchet. To check operation of your latch before closing the tail gate, lock the latches closed on either side. Pull the handle and make sure the latches have released on both sides. Now we know that we can open and close our tail gate properly.

Reinstall the steel cover on the top of the tail gate. If you don't have a plastic cover, you can skip this next step and just start bolting it down. Since we have one, we'll install our plastic tail gate cover and our eight T-30 Torx screws.

Close your tail gate. Make sure that the latch works properly.

Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.