Replaces
Part Details
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video we're going to show you how to remove and reinstall a rear door handle, the outside door handle, on this 2005 Dodge Durango, much the same for any 2000 Ford, '09 Durango, as well as the procedure's the same for the Aspen. Tools you'll need are a small flat blade screwdriver, a Phillips screwdriver, and an 8mm wrench or socket and ratchet.
First there's a little trapdoor in here. Use a small flat blade screwdriver to go in and pry it out. You have a Phillips screw there, as well as one down here and one further back. I'm going to speed it up here as I use a Phillips screwdriver to remove those three screws. Once you have those screws out, lift up and pull out on the panel. Back in here you'll see a little blue clip. Pull that blue clip off. Pull that up and out, and then your connector for your window switch is right here. Press on the little tab. Now just pull the panel off.
Pull your water shield down enough so you can access the upper inside of the door. There's your door handle right there. See there's a little green clip here. Use your thumb and pull that clip off and pull this rod right out. Now you have two 8mm nuts there and there. You'll need an 8 mm wrench or a socket and ratchet to get these nuts loosened up and they come right off. The handle comes right out.
On your new 1A Auto handle, you would want to switch this rod over. Just unclip it and pull it out. My handle is in good shape so I'm going to put the original one back on as if this is the new one from 1A Auto. Clip it back on and put it back down in. You may have to pull on your handle just a little bit to get it back up in. Restart your 8mm nuts putting them on by hand at first. You can actually see that one right down through this hole if you have a light. Tighten them up nice and firm and about another quarter of a turn and tighten them. Reach in and get the lock rod in place and then snap the clip on. Now put your water shield back up in place. Make sure that the door lock knob is upright, the door latch rod comes through, as well as the harnesses if you took it off that far.
Reinstall your door panel. Put your window harness up in. Reach back there and bring this out; push it down in. Lock the clip on. If you look down there are hooks. You have all these hooks, so you look at the bottom ones to make sure you get the bottom ones in. Bring it up. Make sure the lock goes down and behind. Make sure your lock comes up through. Push the panel on. Make sure it goes in flush, and then lock it down. Now put your three screws back in. Again, we'll fast-forward through that. Three Phillips screws, tighten them up, and tighten them nice and firm don't over-tighten them, though. Put this little trapdoor back on.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a front door handle on this 2005 Dodge Durango. Pretty much the same for any 2004 to 2009 Durango. We show you the front left hand or the front drivers side, which is basically the same procedure as the front passenger side as well. Tools you'll need for the job include a replacement door handle from 1A Auto.com, small flat blade screwdriver, a Phillips screwdriver, and an 8 millimeter wrench or a socket with ratchet.
Take a small screwdriver and kind of push towards the front to pry up on your panel here. That comes up and out and, then front slides out, and then there is three connectors. They just have little tabs. You push with your thumb, pull up and out. Now, in behind here, door handle, just pry out this little cover here with a small screwdriver. There is a Phillips screw there, as well as a Phillips screw, under there, and one further back there. I'll just fast-forward here. I'm just using a Phillips screwdriver and removing those three screws I just showed you. Once those screws are off, just lift up on the panel and then start pulling it out. You'll see a little blue clip back here. Pull that blue clip back off the rod, then pull the rod up and remove your door. Carefully pull this water shield off.
To remove your door handle, look right in here and you'll see two clips, a blue and orange one. The blue one, push it straight back and then remove that rod. Same thing with the orange one. Push it back towards the back of the door and pull that rod out. Then, there are two bolts: one here and one there. Two nuts are 8 millimeter. Just got to reach right in with an 8 millimeter socket with ratchet. A wrench would work as well. Okay, once those screws are out, we'll pull out on the door handle, pull it forward, and right out.
Here's my old handle, new handle from 1A Auto. You do just need to switch the lock over. T20 Torx driver. Take this screw right out. Lock comes out. Into the new one. Fit right in. Put your handle in, pull it out back from there. Pull it out, put it in, make sure the back goes all the way in, slide it back, then get the studs in. Keep pushing it back as you push it in. The door, put your two 8 millimeter nuts back on.
Make sure your rods are free. They didn't get bound up when you were putting the handle on. Tighten up these two nuts. I'll come back in here, make sure this clip is kind of down, push that rod in, and then take this rod here, put it in place, and clip that rod on. For this one, what you want to do is pull your handle out, then reach in there and clip that rod. Pull the handle out, reach in there, grab that clip, clip it on. Make sure unlocked.
Make sure you put your water shield back up in place. To put this panel back on, make sure your harnesses goes in through there. Pull this rod out, put it into that blue clip, and lock the clip on. Now, make sure your door lock goes through there. You can look back in here and see where all the hooks are. Just make sure that the front and rear are going flush to the door. Just going to make sure all the hooks are on correctly. Slide it down. Oops, never realized that this came out. Try to lock this on there. Everything should be nice and tight around the edges. Here, I'm going to speed it up again as I just reinstall the three screws the two at the bottom and the one in behind the door handle. Those three screws hold the door handle down in place. Slide this down, the front end first. This can be a little bit of a pain. Just put this little trim back on.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
