Replaces
Part Details
TRQ side mirrors and mirror components are designed to match the function, fixture, and performance of the original version for easy installation. TRQ mirrors are DOT certified, comply with all federal safety standards, and are independently lab tested to ensure our products comply with all government regulations. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Exact fit - To obtain proper fit and function confirm your vehicle has the exact mirror options listed.
Paint To Match Note:
"Paint-to-match finish" refers to a smooth, paintable surface. This item is not painted. Paint offers better coverage and adhesion, but it is not necessary for installation.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out and next time you need a part for your vehicle think of 1AAuto.com, thanks. In this video we're going to show you how to remove and re-install a door panel on this Ford ZX2. This vehicle has manual windows, so if you have power windows it'll be a slightly different procedure. The only tools you'll need are a small flat blade screwdriver and a Phillip's screwdriver.
On the inside of your panel you're going to find two plastic rivets. With this one here you're going to push in the center, not too hard and then use a little screwdriver and pry it out. You're going to reset it back in when you put it back in. In here this one just pulls out of the center and the whole thing comes out. By the door handle you've going to find two plastic covers. I'm taking those off and removing the two Phillip's head screws underneath. Then we'll just speed up a little bit as we remove those two screws.
On the end of the door two plastic Phillip's head rivets. Unscrew them. Pull out the center. To remove the door handle we're going to use a special tool that's made out of a paperclip. You're going to bend it in an L and then at the end just put a sharp little bend. What we're going to do is push in the door panel and find a clip and when the clip is up we're going to put in our tool, turn it to grab the clip and then pull the clip out. See here, this is the clip. What we did was we just went in, tugged and pulled it out and then this pops off. I'm going to put the clip back in the handle, it slides in the grooves. I'm going to take the door panel and pull it away from the door and pop the clip, the little plastic clips underneath. Just apply a little pressure. Pull the door handle up just a little bit, while I pull it up.
You'll want to pull back your water shield so you can access where the mirror plugs into the harness in the door. Remove your three Phillip's screws. One here, here and here. We'll just fast forward as we remove those three screws. Pull out your mirror. We did this a little out of order. You should have released this clip first. Just use a small screwdriver. You press in on the teeth at the bottom and then the top and pull the clip out.
With the old mirror and the new mirror from 1A Auto, they are identical and they are going to go in just as they came out. You stick your harness through. Slide the mirror and put your screws back in. Again, we'll' fast forward here as we just put those three screws back in and tighten them up. Put your harness back in. Reconnect it. Putting the door back on, the door panel. I'm going to put the door lock rod back in.
Push it forward.
Okay. Slide the cover back on. I'm going to start by putting my hand through and pulling the door handle and getting that kind of lined up and then snapping the door lock button in its' place. It's a matter of getting the window seal here up and over the top of the door. Pressing down and seating that. Make sure your screw holes line up. Then pop your buttons back in. Put the trim piece back on, center it. Snap it in. Pop rivet, plastic, this one. My two Phillip's heads. We'll speed up here as we just finish up tightening those two Phillip's head screws. Make those nice and firm and then put all your trim, the two plastic rivets in the back of the door panel and then you're other trim buttons back on.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll free 888-844-3393. We're the company that's here for you on the Internet and in person.
