Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How To Replace Taillight Bulbs 2000-04 Ford Focus
How to Replace Tail Light 2000-07 Ford Focus
How To Replace Taillights 2000-04 Ford Focus 3 Door
Created on:
Tools used
Phillips Head Screwdriver
1. Removing the Tail Light
Open the tail gate
Remove the Phillips head screw from the tail light
Remove the wing nut inside the tailgate access hole by hand
Pull the tail light off by hand
2. Servicing the Tail Light
Pull the harness clips off the tail light assembly
Twist the light bulb bases counterclockwise
Pull the bulbs out of the tail light assembly
If replacing the bulbs, pull the bulbs out of their sockets, and install the new bulbs
3. Installing the New Tail Light
Put the light bulbs into the tail light assembly
Turn the bulb bases clockwise
Connect the harness clips to the light
Put the light into place, threading the bolt through its hole
Push the locating tab into its grommet
Attach the wing nut to the bolt inside the tail gate
Insert the Phillips head screw
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, I show you how to service the taillight on this 2003 Ford Focus ZX5. The only tool you'll need is a Phillips screwdriver.
When you open up your tailgate, right down here you'll see a Phillips screw. Remove this screw. Then in here, if you look up through here you'll see an access hole here with a wing nut. Remove that. Now this comes right off. On the back side there are two bulbs. These twist counterclockwise. You actually can pull these little harness clips that pull right off the light. Twist this counterclockwise; it comes out. Twist this one counterclockwise; it comes out. If you're just looking to change the bulbs, this one pulls straight out and this one does the same.
You can see that my current light is in good shape so I'm going to reinstall it. Put the light in. You want to line it up and then twist to lock. Put this one in, twist to lock. Put these back on, the studs. Down in. There's a little tab right up here. You kind of peek back in, see it, it goes into like you wanted and locks into place. Reach up under and put this back up in. Then a Phillips screw goes right into place. Tighten it up, and you're all set.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Gloves
Phillips Head Screwdriver
1. Removing the Tail Light
Open the hatch
Turn the wing nut on the tail light counterclockwise
Remove the Phillips screw from the tail light
Pull the tail light assembly straight off
Press the lock tabs and disconnect the wiring harness
2. Installing the Tail Light
Connect the wiring harness to the socket
Insert the tail light into place
Tighten the Phillips screw to the tail light
Turn the wing nut on clockwise
Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years.
What's up, guys? I'm Andy from 1A Auto. Today I'm going to show you how to remove and reinstall the rear taillight on this 2001 Ford Focus. If you need parts for your vehicle, click the link in the description and head over to 1aauto.com.
First we're going to pop the hatch. We'll use the key fob. Push the button and open the hatch.
Inside this rear hatch you're going to need to take this wingnut off right here. Just grab it and twist it off. Pull that off. Then you're going to take a Phillips head screwdriver. We're going to take this Phillips head screw out. Just pull that screw out. Grab the light assembly. Just going to slide it out just like that. There's a connector right here. You disconnect the connector here. Just push down on the button release the connector. There's the button. Just push that down.
A little wire retainer right here. Pull on that. We're going to disconnect this connector. There should be two little lock things on this. This one they're actually broken. Pull that out just like that and there's your taillight assembly.
Let's reinstall this. Line this connector up. This one happens to be broken so it's not going to lock in place, but we press it on like that. This wire retainer goes right here.
It's kind of hard to get this one in. I'm going to connect this lower bulb first. That's for the reverse light bulb. Connect that, and then you can reinstall that retainer. There's a couple of pins. This pin lines up with that hole. There's another pin that lines up with that hole. Get that in position. With that all set, we can take the screw and tighten this down. Just snug, not too tight. It is plastic. I'm going to reinstall the wingnut. Get this lined up. Get it on there. Tighten it down. There we go.
Thanks for watching. Visit us at 1aauto.com for quality auto parts, fast and free shipping and the best customer service in the industry.
Tools used
Phillips Head Screwdriver
1. Remove the tail light
Pop the trunk hatch.
Remove the Phillips screws securing the tail light in the jamb of the hatch.
Unscrew the thumb screw on the back of the tail light assembly in the trunk.
Disconnect the wiring harness and bulbs.
2. Install the new tail light
Connect the bulbs and wiring to the new tail light assembly.
Mount the tail light onto the vehicle.
Secure it with the thumb screw and Phillips screw.
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet. In this video we're going to show you taillight replacement. Both replacing the bulbs or replacing the whole taillight assembly on a Focus three door. Tools you'll need are a Phillips screwdriver and that should be about it, actually.
There's a screw right here, and then, in underneath, there is a finger nut right there. You can just grab on that out with your fingers and twist it. The first thing we'll remove. The light comes out. If you're looking to replace a bulb, right up here, this turns counterclockwise and comes out. This one, same thing. Counterclockwise and comes out. To replace this whole assembly you're going to want to pull these little tabs off. There, that's off. These bulbs just pull out and I'm not sure, on this car, whether that should be a orange bulb or not. Looks a little weird. Think it should be clear. This one pulls out, goes back in.
For reinstallation, we can put our bulbs back in. Put these little harness holders back into place. Put that down in. Start our screw in. Back under here, put our thumb screw in. Don't make it too tight because as it gets older it'll tighten up more and it'll be hard to get off.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free. 888-844-3393. We're the company that's here for you on the internet and in person.
330-1914L-US
In Stock
Product Reviews
Loading reviews
4.00/ 5.01
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
0
1
0
0
0
Tail light and Head Light
Douglas
February 19, 2017
The tail light and head light worked and delivered fine however unfortunately my daughters Ford Focus head gasket went at the time I was going to install and I ended up doing a sacrifice sale . I returned the part and received a full return . Everything looked original and the only thing that was not on the tail light was a stainless steel clip that also has a rubber round seal which I believe helps hold the light in place while you affix the screws and also a gasket around the perimeter of the tail light . In other words you get what is on the picture and you need to remove items from your tail light . Good price considering Ford dealer wanted $200 for it and almost the same for the headlight
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Ford is a registered trademark of Ford Motor Company. 1A Auto is not affiliated with or sponsored by Ford or Ford Motor Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.