Replaces
Part Details
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hey, I'm Brian, I'm here to give you guys a little tutorial on some window regulators. The specific design is the scissor design. We actually get a lot of calls on these products here and the common question is: The part I received seems different than the part in my vehicle.
The scissor design actually has a flip design and we're actually going to show you how to fix this here. The most common thing that you want to do, or the first step you want to do is lay the parts out side by side. Try not to match them up in the car because this can get confusing. Take it out, lay them side by side, and what you actually see here is a same exact part for the same model vehicle in the same door. As the appearance shows here, they seem to be mirrored.
If you look down at the bottom here, we have the power window motor. This is the piece that is actually powered to lift and lower your glass. The next section down here is . you actually have your gear drive. Here's your mounting plates on both. As you can see, it's identical. You have your tension spring here. If you notice on the upper section here, it's kind of reversed. You're going to think normally, I get the wrong side door. You're going to give us a call and you want to express that to one of our customer service reps. I'm going to show you how to fix this.
Basically, pick this up by the base and you want to scissor or flip. This is how you're going to fix the issue. It's going to actually match the component as shown there. You can now see that both of these components here are the same part and you're ready for installation.
You should be good to go. Click on Subscribe or check us out at 1AAuto.com. We'd be more than happy to have you join on board and join the 1AAuto team.
Thanks for tuning in. We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly: that's going to save you time and money. Thank you and enjoy the video.
In this video, we're going to show you how to replace the power window regulator assembly in this 2003 Ford F250. We're going to do the driver's door. The passenger's door is, basically, the same procedure. This is the same for any '99 to '07 Super Duty that has power windows. Tools you'll need are 7 millimeter, 8 millimeter, 10 millimeter, and a 7/32's inch socket with a ratchet and extension; flat blade screwdriver; and some painters tape.
To prevent your battery from running down while you have your door open, disconnect the negative cable. An alternative is you could just pull out your interior light bulbs. That way you can keep the battery connected and still be able to run the window up and down when you need to.
Using a small flat blade screwdriver, take this lens, pop it off. Mine is actually broken. It should pry out here, pop it off. Here, you're going to do the same thing. You just pull up with your hand or use your screwdriver a little bit right in the front. You pull that up, pull it forward, and then you disconnect all the harnesses. There's little push tabs on them. Push on the tab with your thumb, pull the harness here, push on the tab right here. The tab here, push on it a little bit. Do the same thing here. You just pull down this trim panel. It's got two clips that hold it on. Now, there are two 7 millimeter bolts: one right there and then one right there. Use a 7 millimeter socket with a ratchet and extension. A wrench would work as well. Fast forward as I just remove those two bolts. Once those two bolts are out, just lift up on your panel, bring it out. Then, in behind is your courtesy light. Just turn it counter clockwise and pull your socket out. Your door panel comes off. You'll want to remove your speaker too, and it's a 7/32 inch socket. Take the speaker out, and then there's a little tab here, disconnect it. Remove your shield the rest of the way.
I've got my switch plugged in and key on. Actually, you can see that my motor and regulator are working just fine. What we'll do is, we'll do the worst case scenario, which is if your motor or regulator breaks in the up position. Now, disconnect your lead. It's right back here through the speaker hole. Just press, and pull. Now remove these four bolts that hold the regulator and these two nuts that hold this track. I'm just going to fast forward as I remove the two nuts from the track. Then, also I remove three of the bolts that hold the regulator bracket, and I'll slow back down here as I start removing the last one. You just saw my window actually slid down some, so that's actually the regulator turning. It's okay. I'm holding the window with one hand. Pull this back out, and the whole thing comes down. Now you want to loosen two nuts: one there, and then when the window's low enough, you can see that one through there. Once you loosen those, then the track just slides forward and comes off. Now, with those loose, the track slides forward. Be careful. Now my regulator is basically free from the window. Now I can pull my window back up. With my window up, you can see I've got some painters tape up here. Put that on. It holds it in place for right now. Back down here, this comes out, come together. There's your regulator out.
Here's our new regulator from 1A Auto. All the same, only sight difference is it has a little bit of a pig tail, but it's going to plug in correctly. The only thing I've done is I started all my bolts in, and I started my two nuts on this track here. What we're going to do is put those together like that, feed it in, and push through. You just have to get these bolts right through. Put our mechanism in place up here, so these four bolts are now in their slots. Put this here, pull it in. Now I can tighten all of those up. Just hit the fast forward button here, as I tighten those four bolts that hold the regulator and the two nuts that hold the track back up. Now to connect the motor, since this has a harness on it, what you probably want to do is take your door harness, feed it down and around your harness down here a couple times. Then connect this harness to it. I'll show that to you. What we did is we just wrapped our harness around here a couple times and then plugged it in right down here. That just keeps the harness away from the window. Just make sure that there's plenty of room for the speaker as well. I can see one of my window mounting points here. The other one is just a little bit low here, so I'm going to turn my key on, plug my window back in, and just run that up a little bit. Do a little test to make sure it works well. Now you can see my window mounting point there, and then that one right there. Slowly let my window down. Now grab my window here through here, lift it up a little bit, pull the regulator down, and let the window come down slowly. Now, I'll slide my track on the back first. It's on the front. Slide it back. That nut's there properly, and that one in there is where it's supposed to be. Tighten that one up. Tighten that one up. Turn the key on, plug in the harness. Everything is working nicely.
I'll speed up as I put the water shield back on. What I like to do is find one point, like where a screw goes through, and you line up that point and then go out from there. Then reinstall your speaker, make sure that you plug it in first, and then reinstall the four 7/32 inch bolts that hold it in place. To reinstall your door panel, what you want to do is take your bottom clips, and they're actually designed to just go on here and rest in place. You can reach down and put in your courtesy light and turn it clockwise to lock it in. Then, make sure all these harnesses come up through. Force it against, lift it up a little bit. Make sure your door lock comes through, and clip it against. You lift it just up a little bit, push it in, and bring it down on to make sure you're nice and tight against the door, nice and tight against the door over here. We'll speed it up again as I take those two 7 millimeter screws, put them in, and then tighten them up nice and firm. Now I'm going to clip the molding on up top to cover the mirror mounting holes, and then take my switch panel, and reconnect all my harnesses. Then I slide the tab back into the back first, and I make sure the wires are getting pinched in there, and then I clip it down in place. That's all set. If you disconnected your battery, then reconnect it and tighten up the 8 millimeter bolt.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
