Replaces
Part Details
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the front struts. This is a 2005 Ford F-150. It's exactly the same for any 2004, the new body style, through the 2008, and probably the same for 2009 and up. We show you on the driver's side, but the passenger's side is the same procedure and we do recommend you replace them in pairs. You'll need new front struts from www.1aauto.com, sockets from 8mm up to 30mm, a pipe or a breaker bar for leverage, a 12mm 12-point socket, 18mm and 21mm wrenches, pliers, pry bar, flat blade screwdriver, torque wrench, hammer and jack and jack stands.
Start off by prying off the hubcap. Then loosen up these lug nuts using a 21mm socket and ratchet and a piece of pipe for some extra leverage. Then raise the vehicle, and remove them the rest of the way and take the tire off. You want to life the whole front of the car up and put it on jack stands with both wheels off the ground. Now pull the wheel off. Now turn the wheel, and remove this 21mm nut at the top of your outer tire rod. Then once you remove it, you want to just put it back on just a couple threads.
Now hammer the knuckle until the outer tire rod drops down. Now you can remove that nut, and just set your outer tire rod off to the side. Underneath your control arm, on the bottom of the sway bar link you want to just remove that nut. You can try doing it with an 18mm ratchet, but most likely it's going to start spinning, and the solution for that is an 18mm wrench and an 8mm socket and ratchet. Then you can just remove that nut. You want to spray the bolt that holds the bottom of your strut, and then a 30mm socket. I'm using a breaker bar and a piece of pipe and break that free. Then once you get it going, the bolt will most likely spin. Hold the bolt end with the 27mm socket and take that nut off.
Then spray these 15mm nuts at the top of the strut with some penetrating fluid, and remove two of them all the way. The other one, you just want to leave on a few threads. Using a pair of pliers, remove this cap. Then loosen up and remove that 13mm nut. Then you want to just put it back on just a few threads. Tap it with a hammer and make sure it goes through. Then remove the nut the rest of the way. On the other end of the axle, there's a series of 12mm bolts. You just need to use a 12mm 12-point socket, and then a pry bar to hold the wheel. Just loosen those up.
You can also just have a helper get in the vehicle, and hold the brakes to hold the axle in place. When you remove that last one, just push the axle down to the side. Now spray this 21mm nut up here on the bottom of your upper control arm. Then remove that nut, and put it back on just a few threads. Now with the nut back on a few threads, just hammer the wheel knuckle until the upper control arm loosens up. Now just lift up on the wheel knuckle, and then remove that nut. Now you can just set the wheel knuckle off to the side carefully.
You don't want it to strain those brake hoses. Then just tap the axle and pull it out of the wheel knuckle. You want to feed the axle towards the left side towards the front of the vehicle. Then just angle it down, and pull it down and out. Now, we're just going to check up underneath the control arm a little bit. The vehicle is still supported on the jack stands under the frame. Remove the bolt from the bottom of the strut, and you can see the struts in there are still loose. Make sure the nuts on the top of the strut are removed. Pry the strut out.
Up top is the old strut. Below it is the new one from 1A Auto. You can see they're identical and they'll fit exactly the same. Feed your strut up into place. Push those studs through. Then just replace those nuts at the top to just hold it. You don't need to tighten them up right now. You're just putting them there to hold it in place. Then pry the bottom of the strut back into the lower control arm. Then push that bolt back through. You just make sure it's all the way in. Then replace the nut and tighten it up preliminarily. We'll just fast-forward as Mike goes back over those 15mm nuts making sure they're tightened. Then you can remove the jack.
Feed your axle back into place. You want to feed it back in the same way that you pulled it out. Then just angle it back down into the hub and push it in. Now you can take your upper control arm and push it back into the wheel knuckle. Once you push it through, just put that 21mm nut on there to hold it in place. Line up the axle and replace those 12mm bolts. We'll fast-forward as Mike does this. Now tighten each of those to 60 foot-pounds in a crossing pattern. You can see we torqued that one. Then you want to turn the wheel until you get the one on the opposite side. Then torque that one. You want to just repeat this process with each of them. Now replace this 13mm nut and torque it to 20 foot-pounds. Then replace that cap and just tap it into place.
If any of the lines on the back came undone, make sure you push them back in and re-clip them. Then push your outer tire rod up to the wheel knuckle and replace the nut. Then torque that to 111 foot-pounds. Now just tighten up this bolt on your upper control arm. If the stud spins, use a 10mm socket and ratchet. Then you want to torque this to 111 foot-pounds. Then tighten up the nut on the bottom of your sway bar link. Jack up underneath the lower control arm to simulate a wheel being in place. Torque the lower strut bolt to 150 foot-pounds.
Now we'll fast-forward as Mike replaces the wheel and replaces the lug nuts and tightens them preliminarily. Then he lowers the vehicle and tightens them the rest of the way. Then torque each of them in a crossing pattern to 120 foot-pounds. Then just replace your hubcap and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Tools used
Tools used
Tools used
Tools used
Tools used
Okay friends, to get started on this job, the first thing that we need to talk about is safety. You want hand protection and eye protection at all times. With that said, safely raise and support your vehicle so you have your front wheel off the ground. We're gonna remove this center cover and then we're gonna remove the lug nuts as well.
Get your wheel off of here. We need to get this cotter pin off of the outer tie rod end now, and we'll need to get the nut off of there. Use your 21-millimeter socket and remove your nut. I just put this back on there, just a couple threads because now we're gonna use our hammer, and we're gonna hit right along here on the knuckle, being careful not to damage the tie rod. Let's get this off of there. Pull this down.
Next, we need to get the mounting nuts off of the top of the strut area here. There's gonna be three of them. There's gonna be two right here where you can see, and the other one is gonna be located further in. You definitely don't wanna touch this center nut in any way. So I'm just gonna use my 15-millimeter wrench, because it's the easiest thing to get into this space. Put it right up on here, and then, of course, a nice rubber mallet, because I don't want to damage my tool.
I'll get this nice and loose. Do the same to the other two, and then we'll remove the nuts fully. As you can see the inward nut is much easier to get from inside the engine compartment. Let's get this one right off of here. We're gonna leave one of the nuts on here just a few good threads. That way there, there's no chance that this strut can fall out. Moving down the strut, if you were to look, you're gonna see a big old bolt with a nut. Using your 30-millimeter socket, you're going to go right here and remove this nut. And I'm gonna hold the bolt head with some pliers. Now, I'm just gonna drive this bolt out of here.
Next, we're gonna use a nice long pry bar, and we're gonna come right under here. Go ahead and pry and you should see it want to separate. We'll pull it away from the control arm. You can see our safety nut did its job. Remove that nut, and remove your strut unit. The next step is to take off our upper ball joint nut. Take that nut, and just put it back on there a few good threads.
Next, we're gonna use a hammer and hit directly on the knuckle right here. That's gonna shake this free, and you're gonna notice that these two are gonna separate. Pull down on this. Remove the nut. Now as this comes up, your knuckle is gonna wanna fall away. Obviously, you don't want to let it continue to fall, because you could put a tug on your ABS wire or even your brake hose. If you have something as simple as a coat hanger or maybe even one of these bungee cords, it's gonna come in handy.
Next, what we need to do is remove the bolt that comes through from the inside of the strut tower to the outside. I'm gonna hold this nut with a 21-millimeter wrench, and then I'm gonna remove the bolt side. Do the same to the other one real quick, right off of there. Grab onto that upper control arm, and get it right out of here. Now you wanna inspect your bolts. You wanna make sure they're in great condition. If they're rusted, or rotted, or they seem like they're weak in any way, of course, you're gonna wanna replace them. Also, take a peek at your threaded area. If it looks like it's rotted and the bolts or the nut isn't gonna be able to hold on like it should, obviously, try to clean it up, and replace them if need be. These actually look pretty good. I can clean them up a little bit. But, nevertheless, what I'm also gonna do is I'm gonna add a little bit of copper Never-Seez along this area where the bolts are gonna be going through the upper control arm bushings.
Okay, now it's gonna be time to get our upper control arm in here. Let's go ahead and slide it right in. And we remember the bolts go from the inside, and they're gonna go facing out. So go ahead and line up the bolt holes, slide the bolts through, and then, of course, we'll start the nuts, we'll snug them up, and then we'll torque them to manufacturer's specifications.
Now that we have the bolts in there, it's gonna be time to get the nuts on. Something that I want to mention real quick is your nuts are supposed to have a neoprene layer inside there that works as a lock. If you're gonna be reusing your nuts for any reason, maybe you haven't gotten new ones, that's okay. I would just use a tiny bit of thread locker, but we'll call it your prerogative. Let's go ahead and start these.
The next thing we need to do before we go ahead and snug these up is we need to make sure the control arm's sitting so it's pretty much parallel to the ground. So this flat area right here is gonna be parallel. I like to use a nice pry bar. I'll come through this slot right here, and just get it as close as possible. Obviously, if it's a little too high or it's a little too low, it isn't gonna be too big of a deal. But if you tighten it while it's hanging like this, and I try to stretch this, it's gonna cause an issue with the bushings, and eventually wear them out very quickly over time. Let's go ahead and bottom this out. Same to the rearward bolt.
All right, so now we're gonna go ahead and torque these down to 114 foot-pounds. I'd like to note that usually when I'm using a torque wrench, I try to torque the nut side. I'll hold the bolt side and I'll torque the nut side. As you can tell, there isn't very much space here so I'm gonna go the opposite. I'm gonna torque this side. Let's get this untied. And I'm gonna start our upper ball joint nut on here. Just pull this down. Start the nut on there. If you're having a hard time pulling this down, you could just put your pry bar up across here, and then, of course, go into the slot we used earlier. Let's snug this up. Now let's torque this to 85 foot-pounds.
Now it's gonna be time to get the strut up in here. If you were to look, you can see the area that the strut holes are gonna be. So just line that up. Put this right up in here. There we are. Now I'm just gonna start on all three of those nuts real quick. I like to use a little thread locker on those. If it looks like this needs to be twisted a little bit, you can use a long screwdriver or pry bar. Just come right through the bolt hole, and then you can twist it as needed. Once you think it looks pretty good, I'm just gonna take my pry bar, and then I'm gonna push, and lift at the same time. Okay? This is working its way right in there nicely.
Now we need to grab our bolts because we want to have it ready so once we have this lined up, we can go ahead and put it right through. Before we go too much further, we need to make sure we inspect our bolt, clean it, and, of course, make sure the threads are nice and clean and safe. Once we've done that, we'll add a little bit of thread locker, and we'll continue. So I got the bolt cleaned up. You'll notice I put on my thread locker like I said I would, and I also put a little bit of copper Never-Seez on the shanked area here. I wanted to make sure I didn't get any Never-Seez on the threaded area though. With that said, let's get this lined up, and get the bolt in. There we are. Let's get the nut on there. Now we're gonna go ahead and bottom this out, and then we'll torque it down.
So next, we're gonna have to torque this nut to 351 foot-pounds, which just to let you know, is a lot. Most torque wrenches don't necessarily go up that high. A lot of them only go up to 250. Torque it as high as you can. Just keep in mind the torque should be 351. That's torqued. Let's get our tie rod end back in here. Now it's gonna be time to get the nut on here. Just make sure if you've got a locking end, that's facing up. Bottom it out. Torque this to 111 foot-pounds. Torqued. Now, we're just gonna bottom out these strut nuts.
So now we're just gonna torque down these nuts. Something to think about though is before you torque them, you need to either have your wheel on and the wheel on the ground with the weight of the vehicle, or you can use a jack stand, but you need to have the weight of the vehicle forcing down on the strut. Now it's time to get our wheel back up on here. Start on all of our lug nuts, bottom them out, and then we're gonna torque them to 150 foot-pounds.
Next you need to get your vehicle so the tire is just barely on the ground so it can't spin. We're gonna torque the lug nuts, like I said, to 150 foot-pounds in a star pattern. Once you've torqued it, make sure you put back on your center cover, of course.
