2005 Mazda B3000 Truck DS Front 8 Piece Steering & Suspension Kit TRQ PSA59525

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks!

In this video, we're going to show you how to replace an outer tie rod on this 2003 Mercury Mountaineer. We show you on the passenger side, but the driver side is the same procedure. The items that you need for this is a new outer tie rod from 1AAuto.com, a 7mm, 19mm, and 21mm socket and ratchet, a piece of pipe for some extra leverage, two adjustable wrenches, a pair of pliers, a hammer, a tape measure, jack and jack stands, and a torque wrench.

Pry off the hub cap by using a flat blade screwdriver in the small slot on the side. Once you get it started, you can just pull out around the edges. If you don't have the benefit of air tools, you'll want to start with the vehicle on the ground, loosen the lug nuts, then raise and support the vehicle on jack stands. Remove the lug nuts, wheel, and tire the rest of the way.

There's a small indent on the inner tie rod. Put the tape measure there and measure out to the center of the grease fitting, which is 9-1/16" in this vehicle. Then, just bend off the legs on your cotter pin on the bolt. Then just pull the cotter pin out with a pair of pliers. Then, using a 19mm socket and ratchet, just remove this nut. Spray this nut with some penetrating oil, and then, using two adjustable wrenches, just separate it. Once it turns, it's loosened up, and you can hammer your wheel knuckle until you see the outer tie rod move. You can see it move right there.

Now you can pull it up and out of the knuckle and twist off the outer tie rod. Up top is the old outer tie rod, and below it is the new one from 1A Auto. You can see they're identical, and they'll fit exactly the same.

For lineup purposes, ideally what you want to do is be able to remove this without turning the inner tie rod. Our bolt or nut didn't come loose. That's not a big deal, but it does mean that we will need to take this and have it aligned because we did turn the inner tie rod a little bit, but we can still put it back together. We'll fast-forward as Mike twists on the new outer tie rod. Remove the nut and then line up the outer tie rod with the hole on the wheel knuckle. You may need to move the wheel knuckle around a bit until it goes down in place. Once you get it in, replace that nut and then just tighten it up. You want to tighten this to about 50 foot-pounds. Once it's fully tightened, make sure the hole lines up with the castle nut, and you may need to turn it a bit more so that it lines up, and then just push your cotter pin through and bend the tabs in opposite directions.

Tighten that nut back on to the outer tie rod using your two adjustable wrenches. Put in your new grease fitting and tighten it up with a 7mm socket and ratchet. Now, just add a few squirts of grease into the grease fitting. Replace your wheel, and then replace all the lug nuts and tighten them preliminarily. Then, you'd want to lower the vehicle and tighten them the rest of the way and torque these in a crossing pattern to 100 foot-pounds. Replace your hub cap, and we recommend you have your front alignment checked and adjusted if necessary.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the front sway bar link on this 2003 Mercury Mountaineer, same as any 2002 to 2005 Mountaineer, as well as Explorer. Our front passenger side is broken, so we show you how to get it out and replace it with a new one from 1A Auto. You'll need new sway bar link from 1AAuto.com, 16mm and 19mm socket and ratchet, a piece of pipe for some leverage, jack and jack stands and a torque wrench.

You'll want to remove your center cap. If you don't have the benefit of air tools, then loosen your lug nuts with the vehicle on the ground. Then raise both front wheels and support the car with jack stands and then remove the lug nuts and wheel the rest of the way. Now you can pull the wheel free.

This is the driver side, which is actually still together, so you would, if you're removing one that was still together, put a 15mm socket and ratchet on top and a 16mm wrench on the bottom, remove that top nut and then go from there. On ours, it's broken so I'm just filling, basically, the cavity with penetrating oil. This is pretty typical: it breaks off up top here and you saw where you just filled it up with penetrating oil and now we're just messing around with it. We locked some locking pliers onto it. That penetrating oil really helped the bolt start up and we've basically broken the plastic here. Now this plastic tube will slide off.

We're just going to use a hammer and chisel to remove the rest of the plastic. This, of course, is the worst case scenario, you just want to remove the plastic, you can use some locking pliers and then just remove the nut on the bottom or at least loosen it up as much as you can. Then just hammer this down and out.

Before installing it, just jack up the other side, just slightly. Now replace your sway link and the order it should go in is: washer, bushing, control arm, then bushing, washer, the tube, and another washer, and then the bushing, and then your sway bar, then another bushing, another washer, and then the nut. You just want to tighten that nut preliminarily,and then release the jack.

To tighten up the link, what you want to do is have the car back down on the ground, and now I have a jack supporting just the front suspension so that basically everything is level and the suspension is in its correct ride height. Then tighten up the link by holding the wrench on top and then turning the bottom. Tighten it up so that the bushings are all squeezed to about the diameter of the washers.

Replace your wheel, then replace all the lug nuts and tighten them preliminarily. Then you'd want to lower the vehicle and tighten them the rest of the way, then torque each of these in a crossing pattern to 100 foot-pounds. Now replace your hubcap. Just line it up and hit it back into place.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks

In this video, we're going to show you how to replace the stabilizer bar links on this Ford Explorer Sport Trac. It's the same process for many of the Explorer Sport Tracs, as well as the regular Explorer Mountaineer, Ranger, etc. We show you on the right side, but the driver side is the same procedure. Items that you'll need for this repair are new stabilizer links from 1AAuto.com, a jack, 16mm and 18mm sockets with two ratchets or wrenches, and you'll need a reciprocating saw if your link is as rusty as ours is, and then some penetrating oil.

Our truck was making some rattling noises, and we can feel a little bit of clunking in the steering wheel. Coming under here, this is your stabilizer bar, and it's linked to the control arm with these links. When you grab hold and shake them, they should be nice and firm. This isn't the best shot, but as you can see, as we grab hold and shake it, it'll move around some. That's causing some of our clunking and rattling.

This repair, actually you can keep the wheel on. I just have it off to make it a lot easier to film. What I've got here is you can see that the lift is underneath the frame so it's supporting it, and I just have the jack under here to put the weight back on so that you can see I can grab hold of the link and move it back and forth. That's how it would be if it was just sitting on its tire as well, but this makes it a lot easier to video.
We use some penetrating oil and spray the top of the shaft. You'll see that was kind of a [mute 00:01:51] point. 16mm socket on the bottom and then an 18mm socket and ratchet on top. You're going to see it just breaks apart, which is actually a good thing.

I can see the condition is really bad, but I'm still going to make a half-hearted attempt. Spray the stud down with some penetrating oil. Then I take a few whacks at it with a hammer, but it makes no movement at all. I'm going to bring in the big guns. Lock onto that top stud with some locking pliers to hold it from spinning. Then, a reciprocating saw, and I'll fast-forward here as we cut through down at the other bushing. There you go. Your old one is out.

Take your new link. Just remove the nut, remove the top two bushings and washers, the shaft, and one of the bottom bushings and washers. You just now have the shaft and one washer and bushing at the bottom. Put it up through, put one bushing and washer with the washer up on, and then put the sleeve on. Jacking up the side you're working on and letting the wheel hang down some will help you get extra space. Now put the washer close to the sleeve and put the bushing on. The little step should go into the sway bar, then push the link up through. Put the top bushing on, then the washer, and the nut. I just jacked the suspension up a little bit more. If you're not taking the wheel off, you would let it down a little bit just so you can get things together and thread the nut on.

You want to replace the other side. You can see I've replaced it. I did it with the wheel on, and I've also tightened it up. Now you want to tighten them up. The new links may be a slightly different size. I think it's a 16mm link and a 17mm nut. When you tighten them up, you basically want to tighten them, make sure that the vehicle is in the correct ride position. Again, if you're just doing it with the wheels on, it's a little simpler, because with the wheels on it's in the correct ride position. You're basically tightening it up until the bushings push out enough so that they're the same kind of size or diameter as the metal washers. If you do end up taking your wheel off, make sure you reinstall it and torque the lug nuts to 100 foot-pounds each.

Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.

Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all backed by our 100% satisfaction guarantee. Visit us at 1AAuto.com, your trusted source for quality auto parts.

In this video, we're going to be working with our 2006 Ford Explorer. We're going to show you how to remove and replace your vehicle's sway bar link in the front. If you like this video, please click subscribe. We have a ton more information on this and many other vehicles. If you need these parts for your car, you can follow the link down into the description over to 1AAuto.com. Here are the items you'll need for this repair.

Using a 19mm socket and a breaker bar, loosen the lug nuts on your tire. Raise and support your vehicle. We're doing this on a lift to make it easier to show you what's going on, but this job can be done at home on a jack and jack stands. Finish removing your lug nuts. You should be able to do this by hand at this point but you can use a ratchet if you need to. You can then remove your wheel and tire.

It may be a good idea to apply some penetrating oil to whatever parts you're going to be working with. Put a 17mm wrench on the nut on the top side of your sway bar link and brace it against the frame of the vehicle. You can then use a 16mm socket and ratchet on the bottom to loosen it. The sway bar link on these vehicles is essentially a series of bushing and washers with a sleeve all held together by one long bolt, as opposed to being a one-piece unit like some other vehicles.

You can see ours is pretty rough here, because there's usually not this much slack. That's actually what your bushing is supposed to look like on all four pieces, one on each side. You can see the old ones are worn down or cut there. It looks like they've actually fallen off over time. Once the nut's out, you can try to remove the bolt from the center of the sway bar link. This can be pretty difficult, so if it doesn't come out by hand, don't be afraid to get on there and give it a good hit with a hammer. The sway bar link will disassemble just like that when you pull it out, so just make sure you have all the old bushing material and all the old washers off of it.

Now you sort of need to build the sway bar link into the truck, so we'll start with a washer and then a bushing. We'll go up through the control arm, install a bushing with the tapered end down, followed by another washer, the sleeve, a washer with the cup end facing up, and a bushing with the tapered end facing up. We'll go through the sway bar, install another bushing. You may need to use a screw jack or floor jack to jack up the control arm to get enough slack on that bolt to install the sway bar link. Then install the washer and a nut and tighten your new hardware down. You'll want a 17mm wrench on the nut and a 16mm socket and ratchet on the bolt end. Just tighten that up until it compresses the bushings so you know that everything's nice and tight and there's no slop in there to make any noise when you go over bumps. Once that's down tight, you can lower the weight off of the screw jack or floor jack.

Reinstall the wheel and tire onto your hub. It's easiest to put a lug nut inside of the 19mm socket to start it onto the studs. Get all five of these down as tight as you can by hand, and then we'll torque the wheel once there's some weight on it. Lower the vehicle back down and put partial weight onto the wheel and tire. This means that you may have your jack or lift under the vehicle. Get the tire to touch and let the vehicle come down some without allowing it completely off of the lift or jack. Torque your lug nuts to 100 foot-pounds in a cross pattern.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the lower ball joint on this 2003 Mercury Mountaineer. We show you on the driver side, but the passenger side is the same procedure. It's the same part and similar process on these Mountaineers from '97 to 2010. The items you'll need for this are a new lower ball joint from 1AAuto.com; 15, 18, 19, 21, 24 and 30mm socket and ratchet; a piece of pipe for some leverage; pliers; snap-ring pliers; a flat-blade screwdriver; hammer; ball joint press; torque wrench; jack and jack stands, and locking pliers, depending on the condition of your sway bar link.

Start off by removing your hub cab and then remove these 19mm lug nuts. If you don't have air-powered tools, you want to loosen them up while the vehicle's on the ground, then jack up the vehicle and support it, and then loosen the lug nuts the rest of the way. Once you've removed those, you'll be able to pull it free.

Now, you want to break off the ends on the Cotter pin right here underneath your wheel knuckle and then you can either hammer it out with a punch or, if the Cotter pin is only sticking out on one side of the castle nut, you can actually just use your 24mm socket and ratchet to break it free. Then, just remove that nut and then put it back on just a few threads.

Remove the nut on the end of the axle and, obviously, if you have air-powered tools it's not a problem. You can have somebody hold the brakes and use a socket and breaker bar if you need to. You want to twist this nut back on until it's flush with the axle and just hammer it until you can see it move. Then come up here and just remove this 18mm nut. With that nut twisted on, again, just a few threads, hammer the wheel knuckle until it drops down. Then, using a 15mm socket and ratchet, you want to remove the nut at the top of your sway bar link. You can hold the bottom with a wrench if it's turning. You can see ours is turning and, in an ideal world, this would just loosen up and you could pull it down, but the top of ours just breaks off.

To help get it out, you want to jack up the other side of the vehicle, and this will lift the sway bar on this side, allowing you to get to the top of sway bar link easier. We'll just spray it with some penetrating oil. Then, using locking pliers, you want to hold onto it while twisting the nut on the bottom of the sway bar link. You'll notice that the plastic will start breaking away and that's fine. You just want to keep repeating the process until all the plastic is gone and you have better access to it. We'll fast-forward as Mike does this. When it gets to this point, you'll be able to remove it and slide it down and out. If it is jammed up, just use a hammer.

Now disconnect your tie rod end, so remove the Cotter pin from the tie rod and I break off the bent over section. I just break it off and then I'm able to pull out the rest of the pin. Then, a 19mm socket, ratchet and a breaker bar loosen it up. You want to take the nut all the way off and then just thread it back on a few threads. Then hit the steering knuckle with a hammer until it pops free. Remove the nut and take the tie rod off and set it aside. If the nut is still on the lower ball joint, hit with a hammer to break it free.

Now support your lower control arm. You can see I have jack stands underneath the frame in the front for both sides. Jack that up with a jack. Here again, make sure the axle is free. I'm not hitting that hard. You don't want to hit your axle too hard because you could damage the CV joints. I'm really just tapping it. Jack it up a little further and now just lift up on the steering knuckle and remove the nut from the lower ball joint. Now remove the nut at the top of the wheel knuckle and pull the upper control arm out of the knuckle.

Take the axle out. Then, you want to take the wheel knuckle and pull it off the stud on the lower ball joints. Just remove that nut the rest of the way. Put it back on there and then just pull the wheel knuckle down and off that stud while pulling your axle out at the same time. It can be a little difficult, but it will eventually go. It's a good idea to just keep it secured to the top of the upper control arm, so just put that nut back on halfway for now.

Using snap-ring pliers, remove the snap ring along the top of the ball joint. Once you get it about halfway, you can just use a flat blade screwdriver and pry it up the rest of the way. With the ball joint press, we've got a cup around the lower part of the ball joint and that there, with a hole through there, so just press the ball joint right down through. I'm just tightening the press and then I hit it with a hammer at the same time, and that just kind of helps to break the ball joint free.

On the left is the old ball joint; on the right is the new one from 1A Auto. They do look similar, but there's some slight differences. However, ours will fit exactly the same. Remove the nut from your new ball joint and then you want to just carefully pry this boot off. Then set up your ball joint press and push the ball joint back into place. Again here, I'm going to tighten it up and just use the hammer to shock it a little bit to help it work its way in.

Once it's all the way back in, just replace that boot and make sure it's on all the way. Take your snap ring and put the snap ring along the top and make sure it's all the way down. Now take your wheel knuckle and you can remove the nut at the top holding it to the upper control arm. Then you want to feed your axle through while putting it back on that stud for your ball joint. This can take some maneuvering, but it will go, and then when you get enough space in the lower ball joint, you want to just replace that nut so it will hold it in place there.

Now push your upper control arm back into the wheel knuckle and replace that nut. Take your outer tie rod and push it back down and into the wheel knuckle and replace that nut. Then you want to torque that to 50 foot-pounds.

Push your new Cotter pin through, or your old one if you managed to save it, then just bend the tabs in opposite directions. Torque the upper ball joint nut to 50 to 55 foot-pounds.

Now replace the axle nut. Tighten it preliminarily. Put a jack underneath your steering knuckle and this basically raises the knuckle onto the ball joint to hold the ball joint in place. You want to tighten that nut up to 70 to 75 foot-pounds, and then further if you need to, to get the Cotter pin through.

Now, you can lower the wheel knuckle and then twist in your grease fitting at the top of the ball joint. We actually end up putting in a 90-degree grease fitting so it's a little easier to grease, and just tighten it up with our 7mm wrench. Then, just top the ball joint off with some grease.

Now you want to replace your sway bar link and you could see that ours was badly destroyed, so we're going to use a new one. You just slide it up through and the order is washer, then bushing, then the lower control arm, then bushing, then washer, then that metal tube, and then another washer and another bushing. Then it should be the sway bar, but you can see that the sway bar is just a little bit too low, so if you jack up the other wheel, you can see the sway bar go up and now you can fit in that bushing. Push the sway bar link up through the sway bar and then do another bushing, then a washer and then the nut. Then just lower the other side and it will compress the sway bar link and then just tighten that up with your 15mm wrench and 15mm socket and ratchet. For your final tightening of the stabilizer link, you can see I've got the vehicle on the ground, and the jack's underneath holding the suspension up in its usual ride height, and then I want to tighten it up so that the bushings basically come out to the same spot as the washers, basically compress the bushings down.

We'll fast-forward as Mike replaces the wheel and then replaces those lug nuts and just tightens them up preliminarily. Then lower the vehicle and torque each of the lug nuts to 100 foot-pounds in a crossing pattern. Then torque this 30mm nut to 184 foot-pounds, and then just replace your hub cap.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.