TRQ ignition coils will have your engine running like new. TRQ ignition coils are manufactured to precise specifications using premium raw materials to optimize each vehicle's ignition system. To ensure peak performance, TRQ recommends replacing ignition coils in sets to prevent electrical output imbalances. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
High dielectric epoxy and reinforced bobbins for extended service life
Rubber, Silicone, or Phenolic Resin Shell: Prevents premature boot wear
Application Specific Design: No modifications required
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Ignition Coil Pack 1990-2011 Ford Ranger
Created on:
Tools used
8mm Socket
7mm Socket
Ratchet
1. Remove the ignition coil.
Mark the plug wires to keep track of where you pulled them from.
Unplug all the plug wires.
Disconnect the wiring harness from the ignition coil.
Unbolt the two 7 mm and two 8 mm bolts to remove the old coil.
2. Install the new ignition coil
Mount the new ignition coil and bolt it in.
Make sure the little resistor attached with the bolts gets reassembled into the ignition coil assembly.
Plug in your plug wires in the order that you pulled them, using your marks.
Brought to you by 1AAuto.com- your source for quality replacement parts and the best service on the internet. Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts, installed correctly that's going to save you time and money. Thank you and enjoy the video.
In this video, we're going to replace the ignition coil on this '04 Ford Ranger with a 4.0L. This coil does fit many Ford V6s from 3.0L up through 4.2L V6s. The only tool you'll need for this truck is a 7 mm and 8 mm socket and ratchet.
Coil on this is a 4.0L in a Ranger; this coil is the same for anything from a 3L to a 4.2L V6. To change the coil, the first thing I've done you can see I've marked these plug wires. I've just marked them basically one, two, three, four, five, six, closest to me then going around in clockwise order. For those of you that know engines, it has nothing to do with the firing order or what number plug these go to. It's just so that when I put them back on the coil, I'll put them on in the right order. If you're planning on changing plug wires, I suggest you replace the coil first and put the plug wires back on, and then just replace the plug wires one at a time.
For this video, we're just doing the coil. I'm going to remove all these wires. It's just a matter of squeezing the kind of lock here, and pulling up and off. These wires from over there, out of the way and these wires over here. Now your connection is right back here. Pull up on here and pull that connector right off. The coil is held on with four well, two bolts and two nuts. These are 7 mm bolts here and 8 mm nuts on the back, and I'll remove those.
Once those four bolts are out, coil comes right up and off. Here's our old coil. Here's our new coil from 1A Auto. You can see everything's the same. It's going to bolt up all the same. You can screw it right down on there. There's a little resistor or capacitor or something here that goes on with the bolt, so make sure you get that correct.
Check these and make sure they're as tight as I want them. Put our connection back in, then our wires. I guess I've got number three here. Again, the marks I have on these wires have nothing to do with the cylinder number. They only pertain to the closest one to me, one, two, three, four, five, six and then around clockwise. Four, five, and six. Now we can start it up and everything should be nice and smooth.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the internet and in person.
ICA61396
In Stock
Product Reviews
Loading reviews
4.80/ 5.010
10 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
8
2
0
0
0
Quick service/fast delivery.
Joseph
August 1, 2017
The part was as advertised, fit perfectly and was easy to install. I found the price very reasonable compared to local part stores in my local area. I have bought from 1 A AUTO IN THE PAST AND WILL CONTINUE IN THE FUTURE.
Good experience
Steven
August 1, 2018
All went well parts received in a timely manner correct parts the video on installation was very helpful and I learned about some new install procedures that made things easier. I will check A1 auto for parts first.
Amazing
D
May 3, 2019
I would reccomend 1A Auto cuz they stand behind their products. And my vehicle is runnin better and not having any issues, im gonna buy more parts for my car then take it to a shop and over price.
Shirley
July 28, 2019
Great low price and durability
Great
Emory
September 28, 2019
I love the service
Ignition coil
G
November 14, 2019
Arrived on time, was easy to install and works great
Good company
D
November 21, 2019
I'm very happy with the prices and quality of product, no more flashing check engine light so I'm thinking I replaced the correct part.
Anthony
October 30, 2021
So far so good
Excactly what I expected
Martin
November 2, 2021
It work fine
Jason
August 13, 2023
Awesome product, just like the original Equipment.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Ford is a registered trademark of Ford Motor Company. 1A Auto is not affiliated with or sponsored by Ford or Ford Motor Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.