Replaces
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a window regulator on this 2004 Ford Crown Victoria. We show you on the passenger's side, but the driver's side is a similar procedure. The items you'll need for this repair include a new window regulator from 1AAuto.com, a flat blade screwdriver, 7mm, 10mm, and 11mm socket and ratchet with an extension, T30 Torx bit, Phillips screwdriver, hammer, punch, drill, 3/8 drill bit, and pliers.
Using a flat blade screwdriver, pry up the switch panel and then pull directly up. Push the tab on these harnesses and disconnect both of them. Pry out this panel behind the door panel and then remove the T30 bolt. We'll just fast-forward as Don does this. Now, lining the outside of the door panel, there are three 7mm bolts. Just go ahead and remove each of those. Pry off this triangular panel, and then remove this 7mm bolt in here. Now you can lift the door panel up and off.
Next, you want to remove your speaker. It's held in with three Phillips screws. We'll just fast-forward as Don removes those. Pull your speaker out, and push the tab on the harness and disconnect it. Next, you want to remove this rail here. Using a punch and a hammer, just hit out the center of these rivets. Then, using your drill and drill bit, just drill out the center of these. You really want to wear safety glasses while you're doing this because of the metal shards. Once you get to a certain point, the rivets will just pull right out. Now that that's removed, you can pull off your water shield.
Now, you want to do the same thing to these two rivets and these three rivets right here. Again, just punch out the centers of each of them. Then drill the rivets out. Now that motor is free, and Don's going to explain to you what to do next.
Our window regulator works fine. It's just a little slow, so that's why we're going to replace it. We have the luxury of being able to lower the regulator to get access to the two rivets that hold the glass to the regulator. In most cases, you're going to be replacing this because it just doesn't work. If it's stuck up or down and you can't get to the rivets, which is through here once we pull it down through here and through here, what you'll want to do is cut your regulator cable on the top and the bottom of the motor with a pair of wire cutters. Here's the wire.
You cut it here, and then that would give you the freedom of being able to move the glass up and down on the regulator. Just have somebody hold it for you while you do it. Now we have access to these two rivets. You want to do what you did to the other rivets. Just punch out the center and then drill them out. You do want to be careful, because they do go through glass here. Be especially careful when you're drilling out those rivets. Just do it nice and slow and use pliers to remove any of the rivet from the back.
Once you've done that you can lift your window up a little bit. Using a flat blade screwdriver, pry off these covers and then remove this weather strip. It just pulls up and off. You want to pull your window up and angle it straight down. Then pull it up and out of the door.
Now disconnect your regulator motor by just pulling back on that tab and pulling the harness free. Now remove these two 11mm nuts at the top of the regulator. Push your regulator back so that those studs come out of the door, turn it sideways, pull it out through this hole here, and your regulator is free.
On the right is the old window regulator; on the left is the new one from 1A Auto. You can see they're identical, and they're going to mount exactly the same. Feed your new window regulator back into place. Just push those studs back into the door and make sure everything lines up. We'll just fast-forward as Don replaces those two 11mm nuts.
In the places where there were rivets, use the 10mm bolts and nuts to fasten the regulator in place. Reconnect your regulator motor harness, and now put your window back down in facing down and then angle it back and push it down into place. Replace that weather strip, and this will help to kind of hold the window in place. Replace these protectors. Just push them together to lock them, and do the same to the other one. Then lower the window down and line it up with the regulator, and replace what was a rivet with those longer 10mm bolts. Now reconnect your switch panel and test out your regulator.
Then you want to line up those bolts with the holes where you removed the rivets through. This gives you a good place where you can tighten up those two bolts. Just tighten them until they're firm. Don't over tighten them because they are through glass. Replace your water shield. Now put that rail back in place and line up the holes. You will need to find two bolts to replace the rivets that you punched out so that you can re-secure this rail. We just used two small 10mm bolts. Reconnect your speaker, line it up, and replace those three Phillips screws.
To replace your door panel, put those lower hooks into place, and then push your harnesses up through that switch panel hole. Line up those other hooks, push the door panel back and down over that lock rod and down into the window sill. We're just going to fast-forward here as Don replaces the three 7mm bolts along the outside, the 7mm bolt inside the door panel, and that T30 bolt. Replace the triangular panel. Replace that panel behind the door handle and reconnect the harnesses. Put the backend of the switch panel in first and push down the front. You're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
