Replaces
Replaces Front & Rear 8 Piece Suspension Kit TRQ PSA63588
$264.95
Replaces Front 6 Piece Suspension Kit TRQ PSA63640
$129.95
Replaces Front & Rear 6 Piece Steering & Suspension Kit TRQ PSA63364
$84.95
Replaces Chevrolet GMC Buick Olds Isuzu Front & Rear 8 Piece Suspension Kit TRQ PSA73492
$67.95
Replaces Front & Rear 4 Piece Sway Bar Link Set TRQ PSA55821
$59.95
Replaces Rear Driver Side Sway Bar Link TRQ PSA67829
$34.95
Replaces Rear Passenger Side Sway Bar Link TRQ PSA67827
$34.95
Replaces Front Lower Ball Joint TRQ PSA66016
$34.95
Part Details
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an upper ball joint on this 2003 GMC Envoy XL and we show you on the passenger's side but the driver's side is the same procedure. The items you'll need for this are a new upper ball joint from 1AAuto.com; flat blade screwdriver; 10, 15, and 19 millimeter socket and ratchet; 15 millimeter wrench; hammer; punch; snap ring pliers, depending on the condition of your old ring around your ball joint; razor; ball joint press; jack and jack stands; and a torque wrench.
Start off by removing your wheel and tire. Pry off the cap first. If you don't have the benefit of air tools, you want to loosen the lug nuts then raise and secure the vehicle on jack stands and remove the lug nuts that way. We have air tools so we put the vehicle up on jack and jack stands to remove the lug nuts and remove the wheel and tire.
Using a pry bar or a large flat blade screwdriver, just insert it in between the axle and the axle housing and just hammer it to separate the axle. Now, remove this clip here, and ours is broken so we're just going to use some wire cutters to remove the wire tie, but normally you just pry the clip open with the flat blade screwdriver. There's a rotating ring that holds the ball joint in. You want to use a punch and a hammer and you can see we do it before we release the upper control arm. You want to get that retaining ring out. Next, remove these two 10 millimeter bolts. We'll fast forward as Mike does that. Just pull the wheel knuckle forward and just make sure your axle pulls free and then support your wheel knuckle with wire ties or string just so that it's not being supported by those harnesses. We're just going to cut off this boot around the ball joint.
With this little tool, we'll be able to press on the hard part of the ball joint and we actually have the augment ours with another little attachment. Then this cup goes around the outside of the ball joint there. Put the press on here. Now, the press will be pushing around the edge of the ball joint and down into the cup and the cup is holding. It's not hitting the ball joint. It's holding around the steering knuckle. It's very important that you line everything up straight. Go nice and slow. You can see the ball joint has been pushed down and out.
Take your new ball joint and push it up into place. Push that up in. You need a sleeve to go up on top and this can just contact right against the bottom of your ball joint. We use the press to push the ball joint up and in and sometimes it helps to just use a hammer. You put a lot of pressure on with the press then use the hammer to get the ball joint, and seed it all the way in. If your old ring is still in good condition, just hit it back into place. Otherwise, use snap ring pliers and put the new snap ring into place.
Push the wheel knuckle back and then just push your upper control arm down on to the ball joint and hammer it down the rest of the way and just slide that bolt through. Replace the nut and make sure you remove your wire ties or string. Push the axle back into place. We'll fast forward as Mike tightens this up. Torque this to 50 foot-pounds. Twist the grease fitting into place and tighten it up with a 10 millimeter wrench. If you have a grease gun, just top it off. Then, just put the bolts back into place and re-clip your harness. Our clip is broken so we're just going to use a wire tie and then just tighten up those two 10 millimeter bolts.
Replace your wheel and replace the lug nuts and tighten them up preliminarily. Lower the vehicle, tighten the rest of the way and torque each of them to a hundred foot-pounds in a crossing pattern. Once you have them torqued, replace you cap then you should be all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
