2008 GMC Envoy Front Passenger Side Power Power Window Motor & Regulator Assembly TRQ WRA51163

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet. Hi, I'm Mike Green, I'm one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20 plus years experience restoring and repairing cars trucks like this to show you the correct way to install parts from 1AAuto.com. The right part, installed correctly, that's going to save you time and money. Thank you and enjoy the video.

In this video we're going to show you how to replace your front window regulator in this 2004 Chevy Trail Blazer. This is the same for any Trail Blazer, Envoy, Ascender 97X, Bravada, and Rainier. Any of these mid-sized GM SUVs. The only tools you'll need are a small and medium size flat blade screwdriver and a 10mm socket, ratchet, and extension. You might want some painter's tape to help you hold your window.

Start with a regular screwdriver, put it up under, quick little pry. Same thing here, pry that up. You can see it just has two clips, front and back. Then you want to turn it over here and you want to unplug all these harnesses. Basically, you just have little thumb tabs, pull them up. Skip that one, this one pulls out very easy. Use your screwdriver, just pry that up a little bit, and pull that off. Then over here, screwdriver on this tab, pry it up a little bit, rip it right out. This comes out. Around your door handle here, you're going to see some little tabs or little slots, you can insert a small screwdriver. Push down with your screwdriver and then pull out with your hand, work your hand underneath. Now the tab right back here, push down pull out. Then there's a couple up top, those ones you push up. One more right here. This whole thing comes out and if you have the memory seat and everything, you can now just pull this whole harness right up and out. Now there are two 10 mm bolts, one there and then one way down in there. 10 mm socket with a extension and ratchet, this one's really easy to get to. Pull it up and out. This one, I'm going to start it, screw it as much as I can.

I just felt it fall, which is okay. Once you have those out, then you can start up here with your hand, just work it underneath this triangle, pull out, and then just work your hand under the door panel. It will get harder and harder to slide under. Then you just pull, keep working your hand under. Pull, work your hand under, pull ... actually here is my bolt from that arm rest. Work our hand under, pull out, and your door panel comes off. We're going to pull back your water shield. You want to pull back carefully, you don't want to rip it. Now with your water shield pulled back, your regulator is held on by a few 10mm bolts, here, here. One up here and one down here. Then this bolt holds your window motor on. As well as ... there are two bolts that hold the regulator to the window. With the window all the way up, you can see one here. Then if you pull this back, there's one right here. Now if your window regulator is broken, usually you can move your window up and down by hand. You can move these into a position where you can get to them and loosen this. That's what we're going to do first.

We're going to loosen these two nuts. Now what we're going to do is, we're going to loosen this bolt. We're going to remove this bolt. We're going to remove this bolt. Remove this bolt, and loosen this bolt. We already know that my regulator is working fine so I'm going to ... so you can see my regulator came right down and my window is still held up. Just for safety sake, I'm going to put a piece of tape to hold that window in place. If your window motor is broken, we saw the regulator with the motor. What you could do if your motor breaks, you can cut one of these cables and then you can move the regulator up and down. Now I'm just going to use a screwdriver to help me push on the tab and disconnect the lead to the window motor. Now the regulator comes up. This is the tricky part. Maneuvering this thing out of here, out of the door. There's my original regulator, new regulator from 1A Auto. You can see everything is all the same. What I am going to do is remove these 10 mm bolts up here, then just transfer them to the same spot on my new regulator. I'm just going to make sure the regulator gets ... the regulator needs to get on the correct side of the window. I'm just going to work it up into place here. I'm just going to fast forward here as I put the other three bolts back in and then tighten all five of them up with my 10 mm socket and ratchet.

We can plug in our lead. We're going to run my window up. I'm going to loosen up this bolt. Make sure this one is nice and loose. I'm going to remove the tape. Let my window slide down, make sure it goes properly into these clips. Now I'm going to force my window all the way up. Now I'm going to tighten up these two nuts. You will notice it goes a little slower on the way up, that's just because the car is not on and the motor is not getting the amperage it needs. There we go, now we can put our water shield back up in place. One thing you want to make sure, is this hole right here is nice and clear. I'm going to fast forward here through putting the door panel back. Just in the interest to keeping the video a little bit on the short side. Once you get it off it's pretty easy to get back on. If you do want to see this in real speed or regular speed, just check out our other video for the Trail Blazer front door panel remove and replace.

We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free, 888-844-3393. We're the company that's here for you on the internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace a rear window regulator on this 2003 GMC Envoy XL. It's the same part and similar process on the regular Envoys from 2002 to 2009. The items you'll need are a new rear window regulator from 1AAuto.com, flat blade screw driver, a 7mm and 10mm socket and ratchet, and a putty knife.

Start off by prying up this little cover with a flat blade screw driver. Then remove those two 7mm bolts. Stick a putty knife behind the door panel and slide it down until you find the first clip and pry out and reach in behind the door panel and just pull out around each clip. Once you remove each of those clips, you can pull the door handle back. Then just push this switch from underneath. It comes up and out. Then push the tab on the harness and disconnect it. You could technically do this before removing the door panel, but you're more likely to scratch up your door panel if you do that. Remove your water shield. Having a razor blade can help because you can just cut at the adhesive, but you can also just pull it free.

This is a cable activated regulator, and a lot of times when they break, what you'll be able to do, you'll hear a popping and grinding noise, and then your window will actually move up and down. So, once you get the door panel off, you'll want to move it to this position where you can get at this 10mm nut and this 10mm nut, and you're going to loosen those. Before we do that, we'll just take a screw driver and push on this tab here and push the connection out. Pull the window up and out of those clamps. Then push the tabs on this clip and push it through the door. Then remove these two 10mm bolts and loosen this top one. Tilt your window regulator and then lift it up and unhook it and pull it down and out of the door.

On the left is the old regulator. On the right is the new one from 1A Auto. You can see they're identical, and they'll fit exactly the same. Remove that top bolt from your old regulator and thread it into your new one just loosely so that you can hang it up in the door. Take your new window regulator, feed it up into the door, push that bolt through the top and hang the regulator and then just line it up and replace those other two bolts. We'll fast forward as Mike does this and tightens them both up. Push this clip back into the door, loosen up these window clamps, reconnect this harness, and then slide the window down into those clamps. Once you have it all the way in and clamped down, tighten up those two 10mm nuts, put your vehicle into accessory, plug in the switch, and just test out the regulator. You can see it works. You can just disconnect the switch and make sure you put your car back in the off position.

We'll fast forward as Mike replaces that water shield. To replace your door panel take the small panel and push it back onto these studs. Then, push the harness for that switch back up through the hole in the door panel. Line up the clips on the door panel, and once you have them all lined up, just hit them into place. Reconnect the switch and push it down into place, and then replace those two 7mm bolts and tighten them back up. Now just replace the small cover, and you're all set.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.