Kit Includes: (2) Front Lower Ball Joints (2) Front Outer Tie Rods (2) Front Steering Rack & Pinion Bellows (2) Front Inner Tie Rods
Quantity: 8 Piece
Specification
Location
Front
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
How to Replace Tie Rod 1992-2000 Honda Civic
Created on:
Tools used
14mm Wrench
Hammer
Torque Wrench
17mm Socket
Jack Stands
19mm Wrench
19mm Socket
Ratchet
Floor Jack
Needle nose pliers
1. Removing the Wheel
Loosen the lug nut covers
Pry off the center cap with a flat blade screwdriver
Loosen the lug nuts with the vehicle on the ground
Raise the vehicle with a floor jack
Secure the vehicle on jack stands
Remove the lug nuts
Pull off the wheel
2. Removing the Tie Rod
Measure from the boot to the outer tie rod and record it
Loosen the 19mm nut on the tie rod with a 19mm wrench
Remove the cotter pin with pliers
Remove the castle nut with a 17mm socket
Hit the knuckle with a hammer
Twist the tie rod out
3. Installing the New Tie Rod
Twist on the new tie rod
Push the outer tie rod down into the knuckle
Replace the castle nut
Push the cotter pin into place and bend the ends in separate directions with pliers
Measure and double check the distance of the boot to the tie rod
Turn the tie rod joint with the 14mm wrench to adjust the distance
Replace and tighten the 19mm nut
4. Reattaching the Wheel
Slide the wheel into place
Start the lug nuts by hand
Tighten the lug nuts preliminarily
Lower the vehicle to the ground
Tighten the lug nuts to between 100 foot-pounds in a crossing or star pattern
Reattach the center cap
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we show you how to replace an outer tie rod on this 1998 Honda Civic. We show you on the passenger side, but the driver side is the same procedure. You'll need a new outer tie rod from 1AAuto.com, 17mm and 19mm socket and ratchet, 14mm and 19mm wrench, a hammer, pliers, a torque wrench, and Jack and Jack stands.
Start off by removing your wheel. You want to loosen up these lug nuts while the vehicle is on the ground, then raise it, and remove them rest of the way unless you have air powered tools and then you can remove it entirely while the vehicle is lifted. Once those are removed, you can just pull your wheel right off.
Right here is your outer tie rod. Measure from this boot to the center of the outer tie rod and remember that measurement. Now, you want to use a 19mm wrench on this nut and just loosen it up, and using pliers remove this cotter pin. Now use a 17mm socket and remove this castle nut, and you may need to just push the wheel all the way in that way you can break it free, and then you can turn the wheel back and remove it the rest of the way. Hit the knuckle with a hammer and that will break the tie rod free so you can lift it up and out. Then we'll fast-forward as Don just twists that off.
On the right is the old outer tie rod; on the left is the new one from 1A Auto. You can see they're identical, and will mount exactly the same. Twist your new outer tie rod into place. Now lift the outer tie rod, push it down to the knuckle, and replace the castle nut. Then we'll just fast-forward as Don tightens this up. Push the cotter pin in place, and then, using pliers, pin the ends of it in separate directions.
Now, measure and make sure it's the right distance. If it isn't, you want to use that 14mm wrench and you want to just turn this until it is the right distance. Once it is, use the 19mm wrench to tighten that nut. Then replace your wheel and your wheel cover and the four log nuts. You want to tighten them preliminary, lower the vehicle, and then tighten them the rest of the way. Then torque each of them in a crossing pattern to a 100 foot-pounds.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
SUS03610
In Stock
Product Reviews
Loading reviews
5.00/ 5.01
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Steering & handling
Mario
October 24, 2020
I was in need of inner & outer tie rods & lower ball joints, everything fit like OEM. I have had these new parts on for 6 months now with no issues.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Honda is a registered trademark of Honda Motor Co., Ltd. 1A Auto is not affiliated with or sponsored by Honda or Honda Motor Co., Ltd.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.