Replaces
Part Details
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
With the vehicle on the ground, I'm going to use a 19mm socket and a breaker bar to loosen the lug nuts. With those bolts loosened, I'm going to raise and support the vehicle. With the lug nuts loosened, I should be able to use just the socket to finish removing them. With that last lug nut removed, I can take the wheel off.
With our wheel off, we can get to the sway bar link. It's bolted to the bottom of the control arm here, and the sway bar on the top. I'm going to use a wire brush to knock off some of the rust and dirt. Help this nut spin off of here. I'm also going to spray these with some rust penetrant. Use a 14mm box wrench, break these free first. That's just turning, but I know it'll spin. Do the same to this one. So those are spinning, because this is basically a little ball joint, so I need to take a 5mm Allen key and hold it. Both are going to be the same way. So they go in here like this. And we use our wrench to loosen it and hold it with this.
To get the 5mm Allen key into the top part of the sway bar link, doesn't quite line up evenly, it's at an angle. We're going to use this floor jack to lift up on the suspension arm. It's going to level it out. Before I do that, I have to put the box wrench on here. Put this on the breaker bar, wrench is in. Hold it and loosen it. If it starts to get harder, stop, spray some more rust penetrant, try to take your wire brush, and clean up some of the threads.
Now we're going to turn the nut back on like we're tightening it. You don't have to tighten it all the way back down. Spray some more rust penetrant, and clean the threads up a little more with the wire brush. Just slowly, but surely, working the nut off of there. Now I have that sway bar link loose, and nut off, I'm going to take the tension off this, just lowering the jack. So that'll come right out. So, both sides will be identical to this, so now I'm going to go after this lower one. I'm going to get this box wrench on here first, put the Allen key in here so I can counter hold it. There it is. That's the sway bar link.
Here's our original sway bar link out of the vehicle. This is our brand new one from 1AAuto.com. It's the same style design. These are left and right, when you go to install them. It comes with new locking nuts. This should fit in here and work great for us.
Take our new one, and slide it up in here. Capture the top nut, and you might have to push this up and in, just like that. These are 17mm, so use the 17mm box wrench to tighten them up. Once it starts to spin with the lock part, so it's turning the stud on the ball joint here, grab our 5mm Allen key again to counter-hold it and tighten this up. Just bring it down nice and snug. Going to do the same for the top. This ones actually tightening without turning the sway bar link on the stud. Let's get it nice and tightened down. Sway bar link is installed.
Reinstall the wheel. Thread the lug nuts on by hand. I'm just going to snug them down. And when I put the car on the ground, I will torque them. I'm going to torque the lug nuts to 80 foot pounds. And then you want to cross pattern.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
