How to Replace Mirror 1998-2004 GMC Sonoma
Created on: 2012-02-20
How to repair, install, fix, change or replace a broken, smashed, cracked, or shattered rear side view mirror on GMC Sonoma, years 99, 00, 01, 02, 03, and 04.
-
step 1 :Removing the Door Panel
- Pry up the window switch panel with a flat blade screwdriver
- Disconnect the window switch wiring harnesses
- Disconnect the door lock wiring harness
- Disconnect the mirror switch wiring harness
- Remove the Phillips head screw inside the door handle
- Remove the door handle bezel
- Remove the two 7mm bolts underneath the door pull
- Pry out the door panel with a door panel clip tool or putty knife
- Lift the door panel up and off
-
step 2 :Removing the Rear Side View Mirror
- Remove the plugs
- Disconnect the mirror wiring lead
- Remove the three 10mm nuts from the mirror
- Remove the mirror
-
step 3 :Installing the New Rear Side View Mirror
- Insert the mirror into place
- Tighten the three 10mm nuts to the mirror
- Connect the mirror wiring lead
- Push in the rubber plugs
-
step 4 :Reinstalling the Door Panel
- Lift the door panel into place
- Push in the door panel clips
- Tighten the two 7mm bolts underneath the door pull
- Push on the door handle bezel
- Tighten the Phillips head screw inside the door handle
- Connect the door lock wiring harness
- Connect the mirror switch wiring harness
- Connect the window switch wiring harnesses
- Push in the switch panel
Tools needed
-
Ratchet
Door Panel Removal Tool
Flat Blade Screwdriver
Phillips Head Screwdriver
Putty Knife
10mm Socket
Socket Extensions
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the mirror on this 2003 GMC Sonoma. The procedure's pretty much the same for any '98 to '04 Sonoma or S15 Pickup. The tools you'll need are flat blade screwdrivers (both regular size and small), Phillips screwdriver, a door panel clip tool or a putty knife, and a 10mm socket with a ratchet and extension.
Start by grabbing the front of your switch plate. Push back and pull up; it should come out. You want to use a screwdriver. On this one there's a tab right here you push. This gray one, probably put your screwdriver right down in here and pry out. Here there's a tab, and then here there's a tab. We'll speed it up here as I disconnect those connections. On the middle one, I believe I did have to use two screwdrivers. I used to one to hold the little locking tab, and the other one to pry up on the connector to pull it off. Right in behind your handle there's a Phillips screw, remove that.
Then this bezel pulls out and unclips, and bring it off the door handle. Up underneath there's two 7mm bolts underneath your door pull, one there and then one right up in there. We'll speed up as I remove those two bolts. If you have a door panel clip tool use that, or actually a household putty knife works just as well. Put the tool in the bottom between the door and the door panel. Slide it, find the clip, pull it. If your door panel's been apart before they'll come off pretty easy. There's one right up here as well. The door panel comes right off.
New mirror, we'll pull these three plugs out. Your mirror is connected right here. Push on a little tab and disconnect it. Then there's three 10mm nuts right in behind there. Speed it up here as I remove those 10mm nuts. As you remove them take care, loosen them way off, and then carefully pull your socket and extension out. The nut should come out right in the socket. Here I'm taking that last bolt out and then as the mirror comes off. I feed the wire harness up in front, mirror right out.
Obviously there's nothing wrong with our original, so I'm going to reinstall it. The mirrors that you get from 1A Auto are exactly the same. They have the same connector and everything. If you have power and heat they can come with that. We also sell manual, as well as the power without the heat.
To reinstall, it's pretty easy, just feed your lead back down in, reach up, and make sure it comes down and through. Put the mirror into place. See my bolts, push it right on. Speed it up here again. You can see I put that bolt on, then put the nuts into the socket, and then thread them onto the mirror. Tighten them up nice and firm, don't over tighten them though. If you have power, or power heat, make sure you reconnect the lead. Then we'll put our three little plugs back in.
Then make sure that the little water shield that's around that opening is back in. Install your door panel. Get it in place, firm all your measure it through, bring it up here. Then push the top. You want to push the top against the window and then down onto the door. Push the top on down. You might have to move it around a little bit, and then make sure the pins go in. Take your 7mm bolts and we'll work them right up in there. Plug everything back in. Back in, the back locks in first and then the front goes down in.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Shop Products
1999-04 Chevrolet GMC Driver & Passenger Side 2 Piece Mirror Set TRQ MRA09221
Part Details:
- 2 Piece
- Paint to Match
- (1) Passenger Side Mirror
- (1) Driver Side Mirror
- Electric
- No
- Black
- Black
- No
- No
- No
- No
- Manual
- No
- Plastic
- No
- No
- Textured
How to Replace Tow Mirrors 2010-18 RAM 1500
Watch this video to learn how to install upgrade tow mirrors on your 2010-18 Ram 1500 truck.
