Replaces
Frequently bought together
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an ignition coil in this 2006 Cadillac CTS. It has the 2.8-liter V-6 engine, and we show you how to replace one of the harder ones, which requires you to pull up the intake plenum. You'll need new ignition coils from 1AAuto.com, various wrenches and sockets, flat blade screwdriver, and a torque wrench to put things back together.
Twist out your oil fill cap, and then pull off your engine cover. Now there's a series of 13mm bolts going all the way back, and you want to just go ahead and remove those. The ones in the back are a little hard to remove, but you want to at least loosen them up as much as you can. For the back ones, we use a small breaker bar and a shallow socket. Using a flat blade screwdriver, loosen up this hose clamp and then pull the air intake box from the front of the intake manifold. Using a 10mm wrench, just loosen up this stud and then twist it free. Then loosen this 18mm bolt. You want to loosen it enough until you can pull that bracket back.
Okay, with all five of these bolts out and that one loosened up, this bracket detached and this detached. You should be able to lift up your manifold enough to access all the coils. Loosen up the 10mm bolt on your ignition coil, and you want to get it out as much as you can and pry out on the tab on this harness and then slide the harness free. Lift up on your intake manifold and pry the ignition coil up, and now you can loosen that bolt more and pull the ignition coil free.
Now, to replace the ignition coil, we can show you on the other side. Just lower the ignition coil into place and twist the bolt back in. Make sure the ignition coil is all the way down, and reconnect the harness. You can see that if you're doing it on this side, you will need to pull that censor out. It just makes it a lot easier, and then it just pushes back in when you're done.
Once you have the harness back in place, push that clip back in. Now you can replace these bolts. We'll fast-forward as Mike does that. Now tighten each of those up preliminarily. Then just torque each of them to 20 foot-pounds. This back one, you just want to tighten firmly by hand, put the stud back in place, and tighten it up with the wrench. Then tighten up that 18mm bolt. Push the air intake box back onto the manifold, and then tighten up that hose clamp. Then take your engine cover, push it back down into place, and replace the oil fill cap.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to be changing out the ignition coil on our 2006 Cadillac CTS 2.8-liter V6. If you like this information, please click the subscribe button. We have a ton more information on this vehicle as well as many other makes and models. If you want to buy these parts for your vehicle, they are available from 1AAuto.com. You can follow the link in the description.
Here are the items you'll need for this repair: 7mm, 10mm, 13mm, 15mm, 18mm socket, ratchet, and extension, 10mm wrench, flat blade screwdriver, rag, brake cleaner, torque wrench, painter’s tape
Remove the black caps over the nuts for the windshield wiper arms. All you have to do is squeeze them together, and pop them off. You're going to use a small piece of painters tape. Make sure you use the straight edge to mark the position and angle of the wiper blade, so we can reinstall our wiper arms properly.
Remove the two 15 millimeter nuts, securing the wiper arms down. The 15 millimeter socket and ratchet. If you're only replacing one arm, you'll only have to do this to that particular one. Work the wiper arms off of the splines. Do this by grabbing them at the joint. Simply pulling up and pushing down. Eventually, it'll work its way off the splines, and you can remove your wiper arm.
Peel off the leather strip. Remove these four 7 millimeter screws. We're going to use the 7 millimeter socket and ratchet. Lift up. Carefully release this plastic, as it's hooked under the windshield. You can see the little hooks right here. Just be careful to pull out and away with those.
Remove this 10 millimeter nut up against the fender on the driver’s side. Lift up and off of the splines for the wiper arms.
Remove the driver's side of the cowl cover. Remove these two 10 millimeter bolts, securing the wiper transmission and assembly into the vehicle. It's a little easier to access this top one from the other side of the hood. We're going to use the 10 millimeter socket, ratchet, and extension. Lift up and toward the center of the vehicle to release this tab. Flip over the assembly. Release the connector. Remove the assembly from your vehicle.
We're going to remove the engine cover. Remove the oil cap. Lift up and pop off the cover, and reinstall the oil cap to prevent any dirt and debris from falling in while we're working. Using a flat blade screwdriver, loosen the intake boot clamp. Pop this back off the throttle body. Remove the yellow safety on throttle body electrical connector.
Push down on the tab, and release it from the throttle body motor. On the bottom of this fitting is a little tab. You want to push that out with a flat blade screwdriver. Remove the fitting from the nipple. Remove these two vacuum fittings. Simply going to pop them out, carefully, pry them out with a screwdriver.
Using a flat blade screw driver, pry the wire loom up off of the intake. Remove the vacuum booster line from the side of the intake. Lift up this sound deadening material, and release these two connectors. Remove these four bolts with a 10 millimeter socket and ratchet. Once all the bolts have been removed, move the brackets they were securing off the side of the manifold and out of the way.
Using a 10 millimeter wrench, remove these three bolts. Loosen this 18 millimeter bolt at the bottom of the bracket. Crack the bolt loose with an 18 millimeter socket and ratchet. Remove these six 13 millimeter bolts with a 13 millimeter socket and ratchet. Using a flat blade screwdriver, release this harness retainer from the throttle body. Remove the intake manifold.
With the intake manifold off, we can easily access all of our coil packs. We're going to do this one here because it's the easiest to film. All of yours will come out the same way. We'll pull out on this safety tab at the end. You may need a small flat blade screwdriver to help. Once this is pulled out, you can remove our connector. Loosen the hold down bolt with a 10mm socket and ratchet. This is a captured type bolt, so it won't actually come out from the coil pack. Once it's unthreaded, lift up and remove the coil pack from the vehicle.
Here we have our old part that we removed from our vehicle and our new part from 1AAuto.com. As you can see, these parts are exactly the same. Four pin connector on the back, captured 10 millimeter bolt on the top. Same length of the boot to go down into the sparkplug tube. Same connector at the bottom.
Some common symptoms of a faulty ignition coil can be a loss of spark, creating misfires or rich conditions in the vehicle. If you've narrowed down that your ignition coil pack is responsible for your check engine light or rough running condition, this new part from 1A Auto is going to go in, direct fit just like your original equipment. Can fix you up right.
Install the ignition coil on to the plug until it clicks, tighten down the 10mm bolt, reinstall the connector, lock the slide back down into place.
Remove your old intake manifold upper plenum gaskets from the intake runners. We'll spray a little brake cleaner on a clean rag or paper towel. We'll wipe all the oil and debris off of the gasket surfaces, both on the plenums of the intake here and on the ports of the manifold itself. Just want to make sure those are nice and clean. Do the same thing here on the bottom side of the intake manifold itself. Wipe off that contact surface on the ports. If you feel any burs or debris build up file that off carefully.
You'll see that there's a small tab that sits into a hole on the top of the runners, as well as a hole that sits onto this dowel on your new intake gaskets. Go ahead and line all that up, and we'll install our intake manifold. Start your 13 millimeter bolts, once you have the manifold set onto its tabs. The longest ones will go into these four counter sunk holes in the center, and the shorter two will go on these outside ones. Tighten all these downs with the 13 millimeter socket and ratchet. Torque these bolts to 17 foot-pounds.
Reconnect the electrical connectors at the rear of the manifold, the brake booster vacuum line, and the two PCV lines; one of each side. Reconnect this fitting to the nipple at the front of the manifold, until that clicks into place. Reinstall the four 10 millimeter bolts for the harness hold downs. Three on the passenger side; one on the driver. You'll then tighten them down with a 10 millimeter socket and ratchet. Line up this bracket. Spin this 10 millimeter bolt in. Tighten up the bolt we loosened at the base of this bracket with an 18 millimeter socket and ratchet. Snug this bolt with a 10-millimeter wrench. Reinstall the sound deadening material onto its pends, as well as the throttle body connector. Lock that safety back into place.
Reinstall the air box on the end. Make sure this vacuum line at the back of that box is still connected. Tighten the clamp with a flat blade screwdriver. Remove the oil fill cap. Reinstall the engine cover. Reinstall your oil fill cap. Reconnect the electrical connector. Set this opening onto the pin. Start tightening down your two 10 millimeter bolts.
Reinstall the driver’s side of the cowl cover first. Be sure that all the plastic hooks line up under the windshield. Reinstall the 10 millimeter nut. Reinstall the passenger side of the cowl cover. Again, make sure all of these hooks line up, and go underneath the windshield.
Reinstall your 7 millimeter screws. Reinstall the rubber seal. The channel simply presses on to this ridge here. Line up your wiper to the tape mark we made on the windshield earlier. Torque to 26 foot-pounds. Line up your wiper to the tape mark we made earlier. Start the nut by hand. Torque the nut to 26 foot-pounds. Reinstall the plastic cap. Close the hood. Remove the tape marks from the windshield. Check for proper operation of your wiper motor.
Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.
