Replaces
Part Details
This Ignition Kit comes with NGK V-Power Spark Plugs and TRQ Ignition Coils.
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an ignition coil on this 2006 Jeep Liberty with the 3.7L V-6 engine. The only items you'll need for this are a new ignition coil from 1AAuto.com and a 10mm socket and ratchet with an extension.
Right here, is ignition coil 1, 3, and 5. On the other side, is ignition coil 6, 4, and 2. We're going to show you how to replace ignition coil 1, but it's a similar procedure. You just pull that hose out of the bracket, disconnect the harness by pushing the tab and then remove that hose clamp. This just pulls right off of the stud. Then, you want to remove this 10mm nut. We'll fast forward as Don does this. Once that's removed the ignition coil pulls right up and out.
On the left, is the old ignition coil. On the right, is a new one from 1A Auto. You can see they're identical. They're going to mount exactly the same. Take your new ignition coil and push it down into place. Now replace that 10mm nut and tighten it up. We'll fast forward as Don does this. Reconnect your harness. Push that hose clamp back into place. Re-clip the hose into place. Then you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you a spark plug replacement. This is a 2008 Dodge Ram. It has the Hemi 5.7L engine in it and this procedure is the same for a lot of different Hemi vehicles, although you'll need different sockets, ratchets, and extensions to get in to different angles and some vehicles you may have to go through the wheel well to get to some of the cylinders.
Items you'll need include new spark plugs from 1AAuto.com, and not a bad time to consider putting new coils on, which we sell at 1AAuto.com, 10mm socket ratchet and extension, flat-blade screwdriver, a 5/8 spark plug socket, dielectric or silicone grease, and you will, again, like I said, need various ratchets and extensions for different positions.
We do show you on one cylinder, but the procedure is the same for all the plugs. You need to use different tools due to different things impeding the workspace. Open up your hood. On each side of the engine, there are four coils. You can see the front one here, and then they go back. It's all the same procedure for each one. Those ones you need to use a short socket and a wrench. Disconnect, there's a little tab on the backside. Push them towards the coil a little bit. Push the tab and disconnect. Then 10mm socket and ratchet and remove the bolts that hold the coils. The bolts have little retainers on them so they don't come all the way out. Once you get it loose, move it around a little bit, and pull them up and out.
To access the plugs on the passenger side, we're going to remove the intake hose and the top air box. There's four clips, unclip them. Loosen this clamp here with the flat-blade screwdriver and pull this hose off, pull this hose off, and bring your intake box up and off and it gives you access.
On this side, you may want to have extension for this second one here. Again, push the connector towards the coil some, and press the tab and release. With our coil out, you can see the plugs are right down inside. 5/8 spark plug socket, very important you have a spark plug socket for this application and know you need various extensions to get down there.
This one's a certain size, so it goes down in, but I can also clear this hose. This is the reason you want the spark plug socket so that the plug will come up and out with it. You want to check the gap, it should be at .040, which is also 1.01mm and gap tool should slide in and out. Actually, it's a little bit big. We'll take the gap tool carefully bend it down just a hair. Lift it in and out.
Again, spark plug socket is the best so you can put it in and then they don't fall out. Put your plug down and in. Thread it by hand first to make sure it gets started, and torque these to 13 foot-pounds. You want to use some dielectric or silicone-based grease and put a little bit right inside the tube that fits over the spark plug. Put the coil down in, you want to push down firmly and start the bolts probably with your hand.
Once it's tight, reconnect the lead, put your air box lid back in, make sure you connect this hose, push it over, get it locked in right, put the tabs up and on. Then tighten up this clamp.
Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.
