Replaces
Replaces Nissan Cube NV200 Sentra Versa 4 Piece Fuel Injector Set Hitachi Automotive HIEEK00009
$378.45
Replaces Nissan Cube Versa Front 10 Piece Steering & Suspension Kit TRQ PSA59597
$314.95
Replaces Nissan Infiniti 6 Piece Ignition Coil Set BBT Automotive Components BBTK00066
$299.95
Replaces Nissan Cube Versa Fuel Pump Module Assembly Delphi FG1149
$263.95
Replaces Nissan Versa Front 4 Piece Drivetrain Kit TRQ CSA70788
$261.95
Replaces Nissan Cube Versa Front Ceramic Brake Pad & Rotor Kit with Calipers TRQ BKA25565
$229.95
Replaces Nissan Versa Front & Rear 4 Piece Complete Strut Assembly & Shock Absorber Kit TRQ SKA60981
$229.95
Replaces Nissan Infiniti 4 Piece Ignition Coil Set Hitachi Automotive HIERK00003
$221.95
Replaces Nissan Cube Versa Front Semi-Metallic Performance Brake Pad & Rotor Kit with Calipers TRQ Performance BKA26273
$215.95
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Install Tip: You may be required to reset the vehicle computer after installation of this part.
Quality Tested - built to a strict level of product standards.
Item Condition:
New
Attention California Customers:
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Hi. I'm Mike from 1AAuto. We've been selling auto parts for over 30 years!
Mass airflow meter is located here, on top of the intake tube, aft of the air filter. To change it, I'll push in on this connector to unlock it. Lift it off, push that down.
There's a screw here and a screw here. It's a six millimeter, or it's a very small Phillips head, you can put in there. I'm going to use the six millimeter ratchet and remove it. Carefully take this one out and don’t lose the screw. Now, on the opposite corner is the other screw.
This is loose. The mass airflow sensor will come right out, straight out.
This is the mass airflow meter sensor. It is keyed on both sides and there's little pins that match on the air intake tube. It only goes in one way. So, this is the correct way. It will sit down nice and even. The screw holes line up. The tabs line up. The lock for the electrical connector’s towards the top. If you tried to put it in backwards, flip it over here, it's not going to fit right. It's close, but it's not quite there. It doesn't really want to line up with the tab. The screw hole doesn't line up. So, if you tried to struggle with this and force it, you could break it. It definitely, when it fits the right way, goes in real easily. You can also tell, there's a direction of flow, so the air is coming from the air filter. It's going into the engine, so it needs to go into this opening and that's how it reads the amount of air going into the engine. It's going to sit in, just like this.
I'll reinstall those screws. These are just really small screws. They're not going to take a lot of torque. I'll get this back one set up. They’re just little machine screws, little insrets in the air tube. You don't want to over tighten them. Get them in there with my fingers. I'm going to take the ratchet and just very lightly tighten them. Right where I feel them get tight, I'm just going to stop.
With those tightened up, I can put the connector back on. It'll click when it locks in place.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
To pop the hood, use the little lever right here to the left of the instrument panel. Pop it up, and now we're going to release the safety. It's a little lever here. Push it to the passenger's side. Lift up the hood. Pop rod is over here. Install it right there.
Going to disconnect the connector on the mass airflow sensor. Push down on this little tab and pull the connector up, just like that. Take the 7mm socket and extension and a ratchet, and take these bolts out. You can also use a Phillips head screwdriver. Just get it loose so you can do it by hand. Get that little bolt out. Take the next bolt out. Be careful not to drop them. And grab the mass airflow sensor and slide it out. Just like that.
Here's our old mass airflow sensor. Here's our new mass airflow sensor from 1AAuto.com. The body is very similar. Has all the same shapes. The connector is all the same. Get yours at 1AAuto.com and be ready to rock and roll.
Insert the new one in the same location. You want these little tabs going towards the front of the vehicle. Take our bolts, little 7mm bolts, and be careful not to drop them. Get that started. Same with this one. Take our 7mm socket and extension and ratchet. We'll snug them up. Just like that. Take the connector, line it up, and then lock it in place.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video we're going to show you how to replace a Mass Air Flow Sensor on this 2004 Nissan Titan and it's the same part and similar process on these Titans from 2004 to 2013. The only items that you're going to need for this are a new mass airflow sensor from 1AAuto.com and a Phillips screw driver.
Your mass airflow sensor is right here. Just push the tab on the harness and pull it free and then remove these two Phillip's screws. We'll just fast-forward as Don does that. Then, your mass airflow sensor pulls right out.
Take your new mass airflow sensor and push it into place. Then replace those two Phillip's screws and we'll just fast-forward again as Don tightens those up. Now reconnect your harness and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
