Replaces
Replaces Nissan Maxima Infiniti I30 I35 Front 6 Piece Steering Kit DIY Solutions SUS02431
$64.95
Replaces Nissan Maxima Infiniti I30 I35 Front 4 Piece Steering Kit DIY Solutions SUS02188
$46.95
Replaces Nissan Infiniti Front Steering Rack & Pinion Bellow EMPI 88-1629-K
$29.95
Replaces Front Steering Rack & Pinion Bellow EMPI 88-1630-K
$29.95
Replaces Nissan Maxima Infiniti I30 I35 Front Inner Tie Rod TRQ PSA68550
$25.95
Replaces Nissan Infiniti Front Outer Tie Rod TRQ PSA68270
$24.95
Replaces Nissan Maxima Infiniti I30 I35 Front Driver Side Sway Bar Link TRQ PSA68037
$21.95
Replaces Nissan Maxima Infiniti I30 I35 Front Passenger Side Sway Bar Link TRQ PSA68038
$21.95
Part Details
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a front stabilizer link on this 2003 Maxima, pretty much the same procedure for any of this era of Maxima. Stabilizer links will rattle if you're going over bumps. Then you'll notice if you're going through turns, at the same time the rattle will go away. That's usually a good sign that your stabilizer link is getting loose. What you'll need is a new pair of stabilizer links from 1A Auto. In this video, we show how to replace the right-hand or passenger side one; the left-hand is the same procedure. We always recommend you replace them in pair. You'll need jack and jack stand, and 15 and 21 millimeter sockets. You'll need a ratchet or a breaker bar and pipe for some extra leverage, and a 14-millimeter wrench. Let's start off by removing the wheel. You're going to want a 12 millimeter socket and ratchet, or a breaker bar or your tire iron.
You'll probably want to start with the wheel on the ground. Loosen the lug nuts. Then raise and secure the vehicle with jack stands. Then remove the wheel and the tire.
I'm removing the 15 millimeter nut on the lower stabilizer link. You need a breaker bar and a pipe. I've broken the nut free, but I'm going to use a 14 millimeter wrench to hold the link rod and continue. We'll speed up here as we take that nut the rest of the way off. Again, using a 15 millimeter socket on one side and holding the stabilizer link rod. It was a 14 millimeter wrench on the other. I'm removing the upper 15 millimeter nut on the stabilizer link. It's the same thing here. You see Don gets going with a little bit of extra leverage from that pipe, then uses a 14 millimeter wrench to hold on to the shaft basically between the boot and the bracket while he removes the nut the rest of the way. We've got two nuts off. Pull out the stabilizer rod.
Here's the front stabilizer link. Now, we'll speed it up as we tighten up both those nuts. You want to get them about as tight as you can with a ratchet handle. You can see that probably the hardest part of this repair is making sure you have a pipe or something to get those nuts loose initially. Once you break that free, then it's a pretty straight-forward repair, taking off two 15 millimeter nuts, taking the part out, putting a new part in from 1A Auto, and then tightening it up.
Fast-forward. Put your wheel and tire back on. Start the lug nuts by hand first, and then tighten them up preliminarily. Set your torque wrench to 100 foot pounds and tighten the lug nuts. Use a star pattern. Draw a star pattern as you tighten them. Then just recheck them.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the right hand outer tie rod on this 2003 Nissan Maxima. Obviously the left hand is the same procedure. This is the same for any 2000-2003 Maxima as well as the Infiniti I30.You'll need a new tie rod from 1aauto.com, jack and jack stands, 15-21 mm sockets. You'll need a ratchet and probably a breaker bar or a pipe for some extra leverage, pliers, a large hammer, penetrating oil, as well as you will, or we recommend, you get an alignment after you replace a steering component like this.
Let's start off by removing the wheel. You're going to want a 21 mm socket and ratchet or breaker bar or your tire iron and you'll probably want to start with the wheel on the ground, loosen the lug nuts, then raise and secure the vehicle with jack stands, and then remove the wheel and the tire.
At this point we're going to measure the distance between the end of the boot and the center of the top of the tie rod. It's roughly 11 and 3/4 inches. Yours might be different. It's always a good idea to use some penetrating oil on the lock nut. Spray that down and let it soak in. With our adjustable wrench, size up the nut holding on to the end of the tie rod, with a 13 mm open ended wrench holding the inner tie rod and free it up. Move the steering wheel to the right to gain better access. We're going to remove the securing cotter pin through the outer tie rod. We're just going to speed it up here as Don tries to get that cotter pin out. We couldn't get the cotter pin fully out, so we're going to use our 19 mm, 1/2 inch wrench and then try and sheer it. In this case we're going to use a little extra leverage with the bar on the end of our wrench. I'll speed it up here as we work that bolt the rest of the way off. Quick summary: we tried to get the cotter pin out. It just wouldn't come out. It was basically frozen in there so what we did is took the pliers and broke the ends off as much as we could and then just got the socket on there and sheered the cotter pin right off by moving the bolt.
To help release the outer tie rod from the spindle we use a hammer and hit against the spindle until it frees up. Now it's free. Pull the inner tie rod with your 14mm wrench and twist off the outer tie rod. OK, speed up and Don did misspeak a little bit there: he is using a 13 mm wrench to hold that tie rod.
We got the old outer tie rod and the new one and you can see that dimensionally they're very close, so when they go back in the alignment should be relatively close to what it was before we removed it. It's always a good idea to put a little anti-seize on the end of your inner tie rod so that if you ever have to replace it again, it'll come off just as easily as this did. Holding the inner tie rod, twist the new tie rod on. Check our length from the end of the boot to the center of the tie rod and it is 11 and 3/4 inches just like it was when we took it out. Place the other tie rod back into the spindle. It can be a little stiff. Now we'll secure the nut and set our torque wrench to 55 foot pounds and we're going to torque the nut. Now what you do is make sure that the hole in the outer tie rod matches the slot or one of the slots on the nut and if it doesn't, giving it a little bit more torque is acceptable to the point where the cotter pin slides through the outer tie rod. Bend the ends that come through back along the side of the nut. With the 13 mm wrench hold your inner tie rod and lock down on the nut. Fast forward here as we take that lug nut back off, put the wheel and tire on, and just put the lugs on by hand first and then preliminarily tighten them. Set your torque wrench to 100 foot pounds and tighten the lug nuts. Use a star pattern. Kind of draw a star pattern as you tighten them and then just recheck them.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
