2001 Mazda B2300 Truck L4 2.3L without OE # ZZR118861 Upstream Bank 1 Sensor 1 O2 Oxygen Sensor TRQ OSA61313

Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all backed by our 100% satisfaction guarantee. Visit us at 1AAuto.com, your trusted source for quality auto parts.

In this video, we're going to show you how to replace the downstream oxygen sensor on this 2006 Ford Explorer. It has the 4.6 liter engine. We show you on, I believe the passenger side; driver's side's the same procedure. We hope you like the video. Please click subscribe. Check out 1AAuto.com for all your parts needs for your Explorer or whatever vehicle you might have. Here are the items you'll need for this repair.

Raise and support your vehicle with jack and jack stands. We have ours on a lift. The downstream oxygen sensors are the ones that go right into the catalytic converter. Passenger side is here and driver's side is over here. We're going to show you how to replace the passenger side one.

Follow your oxygen sensor connection up to this blue connector here. There's a tab right here. Press with your thumb and pull to disconnect. To remove your bad O2 sensor, just use a pair of pliers or a pair of wire cutters and cut the wires. That allows you to easily get a 7/8ths wrench right down and on. Many times these are in there kind of tough, so I like to use a hammer just to give it some impact. A few hits will loosen it up. Use some rust penetrant and let it sit. And then I've got it out a little bit and then put rust oil on there, rust penetrant, and now I'm actually going to thread it back in and see if I can work some down in. The old sensor is out.

Here are the old sensor from the vehicle and the new one from 1A Auto. Remove the shipping protector before installation. The connections are exactly the same. The oxygen sensors are exactly the same. The one from 1A Auto is going to be a very good replacement. It's going to fit and function just like your original. New oxygen sensors are available at 1AAuto.com.

Thread in the oxygen sensor. Use a 7/8ths wrench and use the open end to tighten it up. And then just make sure your lead goes up and the tab is down to go into the connector and plug it in and make sure it clicks.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.

Hi. I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping all backed by a 100% satisfaction guarantee. So visit us at 1AAuto.com, your trusted source for quality auto parts.

Right here, on the driver's side of the truck right behind the catalytic converters you'll find an O2 sensor. This is the rear O2 sensor, also known as the downstream sensor, and it's pretty easy to disconnect on this truck, especially in this case because this truck actually has a brand-new catalytic converter pipe and it has relatively new O2 sensors. So we're going to show you how to replace them.

We're going to use a 22 millimeter wrench. You can come up from the front and get the wrench on their pretty easily, and then it's just a matter of pushing up to loosen the O2 sensor. Then, if you follow the wire up to the top of the transfer case, you can see it plugs in right here. And if you pull on, if you push the little tab down, right here, and then pull on the connector, it should slide right out. At that point, you can come right back around and spin your O2 sensor right out of the exhaust system, just like that. There we go.

When installing the O2 sensor, you always want to put the O2 sensor in first and tighten it up rather than plugging it in first, and that way it makes it so your wires don't get all bound up. So right now, you can spin it into the hole and make sure that the wires aren't getting all twisted up at the same time. Because if you twist the wires up, sometimes they'll actually get damaged and we don't want to do that. So, we'll use the same 22 millimeter wrench to tighten up the O2 sensor from the front just like when we loosened it.

All right. It's nice and tight now. And at this point we can feed the wire up over the transfer case and we can play it right into the wire harness, just like that.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping and the best customer service in the industry.

Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all backed by our 100% satisfaction guarantee. Visit us at 1AAuto.com, your trusted source for quality auto parts.

Right here on the passenger side of the tuck, on the rear, right behind the catalytic converter, is your rear O2 sensor. It's also known as a downstream O2 sensor, and it's quite easy to take out on this truck. This one actually has a newer exhaust system in it, which is actually making it even easier for us. If yours is old and rusty, it'll take a little bit more force, but it'll still work the same exact way. We're going to start with a 22 millimeter wrench on the O2 sensor itself. We should be able to loosen it up just like that. There is such a thing as an O2 sensor socket, which also makes life a little bit easier. There you go, it's actually out of the pipe that easily.

An O2 sensor socket will make it easier because it fits around the whole socket, or the whole O2 sensor itself, and it allows the wires to go through. So you can use a big breaker bar if you need to instead of a wrench that might slip.

Up at the top of the sensor is a connector, which you need to disconnect to get the sensor out of the truck. Looks like it's going to be a two handed thing. I apologize for kind of blocking the camera there, but you can see this is how the clip works. You push down the tab right here and it releases it from the other connector. Whenever you install an O2 sensor, you never want to plug it in first. You always want to install it first, because when you install it. It's going to spin and if the connector doesn't spin, you're going to bind up all the wires and sometimes it'll actually damage the wire. If you're ever putting an O2 sensor in, make sure you screw it in first. Then once it's all the way screwed in, then you plug it in.

Same 22 millimeter wrench is what we're going to use to tighten it. At that point, you can go up to where you disconnected it. It's the blue connector right on top of the transfer case. Where the transfer case meets the transmission, I should say. At this point, it should snap right into place. Just like that. You'll feel it click.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.

Hi, I'm Mike from 1AAuto. We've been selling auto parts for over 30 years! We're dedicated to delivering quality auto parts, expert customer service, and fast and free shipping, all backed by our 100% satisfaction guarantee. So visit us at 1AAuto.com, your trusted source for quality auto parts.

In this video, we're going to be working with our 2001 Ford Ranger, 4.0-liter V6. We're going to show you how to remove and replace your rear or downstream O2 sensor.

If you like this video, please click "subscribe." We have a ton more information on this vehicle, as well as many other makes and models. If you ever need parts for your vehicle, you can follow the link down in the description over to 1AAuto.com.

The only items you'll need for this repair are a new O2 sensor and a 22mm wrench

Your O2 sensor is located here, where the exhaust pipe becomes one single piece again right after this double-up cat. The electrical connector is located up here on the side of the transmission. We'll push down on the tab and disconnect that to start. Using a 22-mm open-end wrench, loosen the O2 sensor socket and remove it from the exhaust pipe. Remove the O2 sensor from the exhaust.

Install your new O2 sensor and thread it in as far as you can by hand. Tighten the O2 sensor back in with a 22-mm open-end wrench. Reconnect your electrical connector and you're good to go.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.

Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all backed by our 100% satisfaction guarantee. Visit us at 1AAuto.com, your trusted source for quality auto parts.

In this video I have a couple of oxygen sensors with me. While there are some aesthetic differences here, the wire lengths are a little different, the actual body and tip of the sensor are a little different, the threads and gasket are the same, and on the other end the connections are actually the same. I can plug these into either position on our vehicle. But if I had to ask you which one's upstream and which one's downstream, you probably can't tell just from looking at them. That's true of most oxygen sensors. The way you determine whether or not an O2 sensor is upstream or downstream is all done visually.

Your oxygen sensor position can be determined relative to your catalytic convertor. As the name suggests, upstream sensors will be located upstream or ahead of, in front of, above, closer to the engine than your catalytic convertors. This means that they see the exhaust gasses first. They then go through the catalytic convertor and to the downstream oxygen sensor, which will either be located in the catalytic convertor like our vehicle here, or after the catalytic convertor to monitor the gasses coming out of the cat and make sure that it's being efficient relative to the readings of the upstream O2 sensor.

The other determination you need to make is bank one versus bank two. Determining which bank is which can be done by looking at a picture of your vehicle's firing order. Whichever bank contains cylinder one is going to be bank one, and the other one, regardless of whether or not cylinder two is in it, is going to be bank two by default. These banks are true of V engines like V8s, V6s, and flat engines like Porsches and Subarus that have individual banks.

On inline four-cylinder engines, as long as they have one exhaust manifold like a Jeep four-liter or a four-cylinder Honda engine, you'll only have one bank with an upstream and downstream O2 sensor. There will be no bank two on the engine.

On our vehicle here, this is the passenger side, which we've already determined from the firing order is bank one. We have our upstream sensor here closest to the engine ahead of the cat. Then we have our downstream or sensor two here inside of the catalytic convertor. This could also be located somewhere after the cat. Here I have my two sensors for the vehicle. While they are aesthetically different, we can now tell this is my upstream sensor because it looks just like the upstream sensor I have up there. This is my downstream sensor. Now that we know which one's which, we can order the right part, correct the problem, and fix you up right.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.