Replaces
Part Details
TRQ brake kits are designed to restore your brake system to like-new performance. TRQ brake pads are positive molded, thermal scorched, chamfered, and utilize a multi-layer shim for enhanced performance and service life. TRQ rotors have a non-directional finish that reduces the break-in period for new rotors as well as reducing vibrations throughout the rotor’s lifecycle. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
In this video, we will be removing and replacing the rear brake pads and rotors in 2008 Subaru Outback. We're going to take off the lug nuts. It's a 19mm socket and a breaker bar. We're just going to crack em loose before we lift the vehicle off the ground. Take the lug nuts out. Grab the wheel and pull it off.
We're going to take the caliper off. To do that, we're going to take these two 14mm bolts out, and we're going to use a 14mm wrench, and take the bolt out. Now when you're taking the bolt out, if this stud is spinning, you can hold it with some channel lock pliers and take it out. Before we take this bolt out, we're going to break free at the top too. Now we can take them both out.
If this caliper's really tight, take the screwdriver and pry it against the rotor. Squeeze the piston down a little bit, and you can pull it right out. Take a bungee cord and wrap it around the spring, and the caliper's out of the way and secure. Pull our pads off. To take these caliper bolts out, you use a 14mm socket on an extension. Pull that out and pull the rotor off.
Our rotor's nice and loose. If your rotor was stuck on there, you could use a hammer and hit on all this surface right here. You also have some areas where you could put a couple of bolts. You could push the bolts in and tap it, and it will help you take the rotor off.
These are our old brakes, and these are our new brakes from 1aauto.com. As you can see, look at the rotors first, the configuration is the same, the screw holes are the same, the lug holes are the exact same. The rotors are the same height. It's got the same bore for the parking brake, and we'll take a look at the brake pads. You can see the brake pads are the same. The squealer is the same—it's got the same stop squeak on the back. And get your parts at 1aauto.com and you'll be ready to rock and roll.
Now we're going to clean up our caliper bracket. Pull off these pad slides and take our wire brush. Clean this up a little bit. Pull these caliper slides out. Spray them down with brake cleaner. Wash them off. Take the other one out. Spray a little brake cleaner. Spray a little brake clean down here. Clean that up.
Take a little bit of brake grease, put it on the caliper slides, and stick that back in. Do the same on this one. Take our pad slides.We’re going to clean off the backside a little bit. Stick that back on. Same with this one. They're pretty clean, not too bad. Not really rusty. Put this one back on here. Take a wire brush to the top side. That's good.
First, before we install the rotor, we're going to put it on backwards. So we can take some brake parts cleaner and clean the backside of the rotor. Wipe it off. When they make these rotors, they put a protective coating on them so they don't rust on the shelf. Spray brake cleaner on this side and wipe it down.
Install our caliper bracket. Take the bolts from the backside. We're going to torque these bolts for this caliper bracket to 47.9 foot-pounds. Take some brake caliper and brake pad grease. Put it on the ears of the pads Then we're going to put a little bit on the surface here. Be careful, don't get it on your fingers. We're going to slide that in, in the backside. There we go. Do the same with the front one. Put a little bit on the ears, and then put a little on the face. Install that. Those are in.
Take the bungee cord off of the caliper, and we want to compress the piston. We're going to use some channel lock pliers. You can use a C-clamp or a brake caliper tool. That's all the way down. Install the brake caliper. Install the brake caliper bolts. We're going to torque these bolts to 19 foot-pounds. Do this one up top.
Install our tire. Put the lug nuts on. With the torque wrench, we're going to torque the lug nuts down to 90 foot-pounds going in a star pattern. You want to go in a star pattern so that you torque the wheel to the hub evenly. There you go.
Now before you drive away, you're going to want to make sure that you pump the brake pedal slowly multiple times cause there will be an air gap between the brake pads and the caliper so when you pump it, it will push the fluid back to the caliper and compress the brake pads.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
