Replaces
Part Details
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks!
In this video, we are going to be working with our 98 Toyota Camry. We are going to show you how to remove and replace your front sway bar link. We happen to be doing this on the passenger side, but the process is the same as the drivers as well.
You want to replace this part as a pair. These are known to get a little bit of play in them and create a clicking or a popping sound as your vehicle transfers weight left and right and loads and unloads that sway bar. You can check them by placing a pry bar underneath and pushing up on the link and seeing if the joints move smoothly or if you can see a gap where the actually sway bar moves before the joint picks up and starts to pivot with it.
If you like this video, please click subscribe. We have a ton more info on this car, as well as many other makes and models. If you want this part for your vehicle, you can follow the link in the description over to 1A Auto.
Here are the items you'll need for this repair: 14-21mm sockets, ratchet, socket extension, torque wrench, locking pliers, breaker bar, jack, and jack stands.
Break all your lug nuts loose while the vehicle is still on the ground. Going to need a 21 millimeter socket and a breaker bar. Install your jack under the vehicle. Line it up with the pinch weld. Jack the vehicle up high enough that you can get a stand underneath. Making sure you have enough clearance to remove your tire or do whatever you have to do under the vehicle. Install your jack stand onto this uni body frame rail under the vehicle. With the vehicle raised and supported, remove your lug nuts the rest of the way. If you need a little more room to work, you can pull the hub cap off. Remove your wheel from the hub. We've put our vehicle on a lift to make it easier to film for you but this job can be easily done with a jack and jack stands.
To remove the sway bar link, we'll use a small pair of locking jaw plyers to grab on to the back side of the joint here and a 14 millimeter sock and ratchet to remove the nut. We'll push it out of the strut and use the same steps to remove the nut and stud on the bottom side at the sway bar. Remove the stud of the sway bar link from the strut and remove your locking jaw pliers. Remove the sway bar from the vehicle.
Here we have our old part that we removed from our vehicle and our new part from 1A Auto.com. As you can see, these parts are identical, same length, we have the same angle, on the heads of the sway bar here there is a right and left of these. This one happens to be the right. Comes with new nuts, with a nylon lock strip inside of them. What happens to these sway bar links is the inside of this joint is a ball and socket joint, much the same as your tie rod or your ball joint is in the front suspension.
It becomes warn out and allows up and down travel inside of that joint which creates a clicking sound and a little bit of play when that weight transfer gets moved from sway bar to sway bar. You can check these by placing a pry bar underneath them and just wiggling it up and down and they should move nice and fluid together. If you see one has the joint moving up before the stud starts to flex, that's a good indicator that you have a bad sway bar link.
This new part from 1A Auto goes in direct fit just like your original equipment does. It'll get your vehicle handling and transferring weight correctly as well as getting rid of those annoying sounds and fix you up right.
Install the bottom of the sway bar link into the sway bar first. We'll put the nut on a couple of threads. These new nuts are 17 millimeter, so we'll be installing them with a 17 millimeter socket and ratchet. Once you have the bottom threaded on by hand, push the top in and start that nut as well. Now these are at kind of an odd angle at first but as we tighten the nuts up, it's going to straighten out and sit where it's supposed to. Remember to clamp your vise grips onto the back side. Be careful not to tear the boots as these are the new parts, so we want to try not to damage them. Go ahead and tighten the nuts down. Torque the sway bar link nuts to 29 foot-pounds.
Reinstall the wheel and tire. Tighten down the nuts. Put the vehicle onto the ground. Check that they are all seated. If you've removed the tire, only lower the vehicle until the wheel touches the ground. With partial weight of the vehicle on the ground, torque your lug nuts to 76 foot-pounds in a cross pattern. Then, you can remove your jack the rest of the way.
Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the front lower control arm in this Toyota Camry. This one is a 1998, but the procedure is pretty much the same for 1992 to 2001. You'll need a new front lower control arm from 1AAuto.com, 12 to 22 millimeter sockets with a ratchet and extension, a torque wrench, breaker bar, pry bar and jack and jack stands.
Break all your lug nuts loose while the vehicle's still on the ground. You're going to need a 21mm socket and a breaker bar. Install your jack under the vehicle, line it up with the pinch weld, jack the vehicle up high enough that you can get a stand underneath. Making sure you have enough clearance to remove your tire, or whatever you have to do under the vehicle. Install your jack stand onto this unibody frame rail under the vehicle. If you need to work on the rear of the vehicle, put your jack stand underneath and just ahead of the lower control arm here, right by the tow point. Once the weight is on your stands, give the vehicle a little shake, and make sure that they're on there secure. Repeat these steps on the opposite side. Make sure that you bring the vehicle up so that when it sits on the other set of jack stands, the vehicle will be level. You can now lower your vehicle onto the stands on this side.
With the vehicle raised and supported, remove your lug nuts the rest of the way. If you need a little more room to work, you can pull the hubcap off. Remove your wheel from the hub. We've put our vehicle on a lift to make it easier to film for you, but this job can be easily done with a jack and jack stands.
Remove the three 17 millimeters holding the lower ball joint bracket in: two nuts and bolt. We use a 17 millimeter socket and ratchet. Using a pry bar, I'm going to go in between the ball joint bracket and the control arm, pry down, and release the ball joint bracket from the lower control arm.
Behind the steering knuckle on the sub frame, we remove these two bolts holding the front portion of the lower control arm in place. Use a 19 millimeter socket and breaker bar to start them and finish removing them with a ratchet. Remove the bolt for the rear lower control arm bushing with a 19 millimeter socket and a breaker bar. After removing the bolt, use a long pry bar to pry the bushing out of the sub frame. You may have to move this a few different ways, and possibly pry up on the sway bar to release it from the vehicle.
You can see our old part and our new part are exactly the same. Our new part comes with new bushings in both the rear and the front. We have the same three-bolt pattern on both sides to reinstall our ball joint into the control arm. They're both the same size and shape. This provision on our new control arm is for a sway bar that's not applicable to our Camry. It may apply to three liter Camrys or perhaps Solaras and other models. You can simply remove that with two, 14 millimeter nuts on the back, we'll show you how to do that a little bit later. Some common problems with these are they get damaged during accidents. They can be bent or misshapen from hitting heavy potholes or bad roadwork. The bushings – as you can see ours is over here – begin to slide out of the actual control arm as well. You can see it's getting a little torn up and separated in the front here too. That can cause a control arm to not track straight. It will actually push back toward the vehicle when you're driving forward. It can cause shaking, clunking, all kinds of noise, tire wear, alignment issues, you name it. If your old control arm has rusted, bent or tweaked in some way, or your bushings are loose and causing vibrations, noise and other problems, this new part from 1A Auto is going to go in, direct fit, just like your original equipment and fix you up right.
Install the rear bushing of the control arm into the sub frame, line it up, and start your bolt. Swing the control arm into position. Use a pry bar, if you have to, to line it up. Start the bolts. The longer of the two goes in the rear hole, and the shorter in the front. With all your other bolts started, pry down on the control arm, push the ball joint into place, start your 17 millimeter bolts and nuts.
Start the 17 millimeter nuts on the bottom until the centering sleeve is gone into the new control arm. Once the centering sleeves are in place, start the bolt, finish tightening down your ball joint bracket. Torque the hardware to 94 foot-pounds. Finish tightening the two, 19 millimeter bolts on the front bushing of the lower control arm. Torque all the 19 millimeter bolts to 152 foot-pounds. Finish tightening down the rear bushing bolt. Torque it to 152 foot-pounds.
Reinstall your wheel and tire. Start your lug nuts. Check that they're all seated. Jack up on your pinch weld. Be sure that where you jack isn't going to interfere with your ability to remove the jack stands. Bring the vehicle up until it's off the stands. Remove your stands from under the vehicle. With the stands clear, lower the vehicle. Move to the other side, and repeat these steps. If you've removed the tire, only lower the vehicle until the wheel touches the ground. With partial weight of the vehicle on the ground, torque your lug nuts to 76ftlb in a cross pattern. Then you can remove your jack the rest of the way. To reinstall your hubcap, align this notch with the valve stem on the wheel. Snap it back into place.
Thanks for tuning in. We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the front lower ball joint in a 1998 Toyota Camry. This information is going to be the same from 1992 to 2001 on the Camry, as well as several other Toyota vehicles.
The items you'll need for this repair are new front lower ball joints from 1AAuto.com, a 17mm socket ratchet and extension, 10 to 19mm wrenches, a torque wrench, needle-nose locking pliers, a pickle fork, a breaker bar, a hammer, pry bar, penetrating oil, and the jack and jack stands.
Break all your lug nuts loose while the vehicle's still on the ground. You're going to need a 21mm socket and a breaker bar. Install your jack under the vehicle, line it up with the pinch weld, jack the vehicle up high enough that you can get a stand underneath. Making sure you have enough clearance to remove your tire, or whatever you have to do under the vehicle. Install your jack stand onto this unibody frame rail under the vehicle. If you need to work on the rear of the vehicle, put your jack stand underneath and just ahead of the lower control arm here, right by the tow point. Once the weight is on your stands, give the vehicle a little shake, and make sure that they're on there secure. Repeat these steps on the opposite side. Make sure that you bring the vehicle up so that when it sits on the other set of jack stands, the vehicle will be level. You can now lower your vehicle onto the stands on this side.
With the vehicle raised and supported, remove your lug nuts the rest of the way. If you need a little more room to work, you can pull the hubcap off. Remove your wheel from the hub. We've put our vehicle on a lift to make it easier to film for you, but this job can be easily done with a jack and jack stands.
Locate the lower ball joint on the back side of the steering knuckle, just below the CV axle. Using a pair of needle noise pliers, straighten out the cotter pin. The head of the cotter pin on the driver's side of our vehicle has been mangled from an improper installation. We'll show you how to get a stuck one out. We'll use a pair of side cutters to break the head on the end of the cotter pin. Once that's split, we're going to use a large flat-headed punch to try to hit the broken ends of the cotter pin where they've snapped off pretty flush with the bolt to try to knock it out enough on the other side that we can grab it with a pair of pliers and pull it through. You want to be very gentle when you hit this. You need to hit it hard enough to move it out, but not so hard that it peens the ends over, and it won't come out of the ball joint. We're going to use a smaller flat punch now to try to push the legs of the cotter pin through as far as we can. We're just going to add a little penetrating oil here, just to try to help get those cotter pins out. Using that same pair of needle nose locking pliers, grab on.
We're going to use a 19mm open end wrench to try to get on there and break the nut loose on the ball joint. You can see that the CV axle might interfere with us removing it all the way, but once we get it pretty close and we know it's going to move, we can separate the ball joint from the knuckle, which will give us the extra clearance we need and allow us to finish removing it. The nut is now coming in contact with this shield around the ring of the CV axle, so we'll have to lower the ball joint down into the spindle to finish removing the nut.
Using a pickle fork, or a ball joint separator, and a hammer, knock the pickle fork in to pop the ball joint out of the spindle. Use that same 19mm wrench to finish taking off the nut. You'll notice I left the pickle fork in there, so if we come in contact with the CV axle again we can just pry down to get the extra clearance we need. We're hitting it again now, so we'll pull down. Finish removing the nut so we have the clearance to do it without hitting the CV axle. Remove the nut from the top of the ball joint.
Using a 17mm socket and ratchet, remove the two nuts and the bolt connecting the ball joint bracket to the lower control arm. After you've removed all the bolts, use a pry bar to pull down on the control arm and release the ball joint.
Here we have our old part from the vehicle and our new part from 1A Auto. As you can see, we have the same bracket here, the same bend to mount the ball joint into, and the same stud on each one of them. Flip them over, and you'll see that they're the exact same, with the exception of the new one being serviceable. We have a grease fitting on the bottom here so when you're down there doing your oil change and other maintenance things, you can grease all your fittings. It helps with the longevity and keeps them in good shape a lot longer.
Our new ball joint also comes with new castle nut and a new cotter pin. Just to give you an idea here while it's a little easier to see, ours was in there incorrectly in the video. They had installed their vertically, like this. If you install it sideways like that, it leaves a loop, and makes it easier for you to grab and take out later. If your old ball joint has a torn boot, it's blown out the grease, or it has up and down play in it, this new part from 1A Auto is going to go in, direct fit, just like your original equipment, and fix you up right.
Here we have our new ball joint from 1A Auto. Flip it over, and you'll notice the bottom of the joint is threaded. It comes with a grease fitting, or a Zerk fitting, that we'll have to install. Just thread it in by hand. With the 10mm open end wrench, just bring it down until it's tight. It’s very fine thread on this so you don't want to crank them down super tight. As long as it's on there snug and it's sealed so no grease comes out, you should be all right.
Install your new ball joint into the spindle and start the nut on there as far as you can. We're going to insert a pry bar into the control arm and pull down until we can install the studs of our ball joint bracket back into the control arm. Start the nuts onto the ball joint bracket. You can see that they have little centering acorns on the bottom there, and that will help us line up the top. Tighten those with a 17mm socket and ratchet. Once the centering portion starts in, move to the other one. Start our top bolt in, bring everything down tight. Torque both nuts and the bolt to 94 foot-pounds.
Tighten down the nut on the top of the spindle with a 19mm wrench. Be sure that one of the windows in the castle nut lines up with the hole in the stud, so we can install our cotter pin after it's tight. We'll install the cotter pin sideways with the longer of the two legs facing in toward the vehicle. Remember that this goes sideways, not vertically. We'll bend one of the legs around the nut. We can leave the other one straight or cut it off, whichever you prefer.
Start your lug nuts. Check that they're all seated. Jack up on your pinch weld. Be sure that where you jack isn't going to interfere with your ability to remove the jack stands. Bring the vehicle up until it's off the stands. Remove your stands from under the vehicle. With the stands clear, lower the vehicle. Move to the other side, and repeat these steps. If you've removed the tire, only lower the vehicle until the wheel touches the ground. With partial weight of the vehicle on the ground, torque your lug nuts to 76ftlb in a cross pattern. Then you can remove your jack the rest of the way. To reinstall your hubcap, align this notch with the valve stem on the wheel. Snap it back into place.
Thanks for tuning in. We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
