Kit Includes: (1) Front Passenger Side Sway Bar Link (1) Front Driver Side Sway Bar Link
Quantity: 2 Piece
Specification
Side Location
Driver & Passenger Side
Location
Front
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Front Sway Bar Links 2006-11 Toyota Camry
How to Replace Front Sway Bar Links 2012-2017 Toyota Camry
How to Replace Front Sway Bar Links 2006-11 Toyota Camry
Created on: 2017-10-30
Tools used
Socket Extensions
Torque Wrench
17mm Wrench
Rust Penetrant
Pry Bar
18mm Wrench
17mm Socket
Jack Stands
18mm Socket
Brake Parts Cleaner
21mm Socket
21mm wrench
6mm Allen Wrench
Reciprocating Saw
Ratchet
Wire Brush
Floor Jack
1/2 Inch Breaker Bar
1. Removing the Wheel
Pry off the hub cap with a pry bar
Loosen the lug nuts with the vehicle on the ground
Raise and support the vehicle
Remove the lug nuts
Pull the wheel off the hub
2. Removing the Sway Bar Link
Spray rust penetrant on the upper sway bar link nut
Clean the upper sway bar link nut with a wire brush
Hold the upper sway bar link nut with a 6mm hex socket and breaker bar
Loosen the nut with a 17mm wrench
If the nut is stuck, hold the sway bar link ball joint with locking pliers if necessary
Remove the 17mm nut
If the nut remains stuck, cut the sway bar link stud with a hack saw or reciprocating saw
Hold the lower sway bar link ball joint with locking pliers
Remove the 17mm bolt from the lower sway bar link stud
Remove the sway bar link from the vehicle
3. Installing the Sway Bar Link
Hang the sway bar link where it attaches to the strut
Slide the sway bar link stud into sway bar
Start the 18mm nuts onto the sway bar link studs by hand
Hold the sway bar link ball joints with an 18mm wrench
Tighten the nuts with an 18mm socket and ratchet
Torque the 18mm nuts to 55 foot-pounds
4. Installing the Wheel
Slide the wheel onto the hub
Start the lug nuts by hand, with the tapered side facing the wheel
Tighten the lug nuts preliminarily
Lower the vehicle to the ground
Torque the lug nuts to 76 foot-pounds in a star pattern
Line up the hub cap with the valve stem
Push the hub cap onto the wheel
Hi. I'm Mike from 1AAuto. We've been selling auto parts for over 30 years!
Use a large pry bar or a flat bladed screw driver to remove the wheel cover. Just kind of slide it between the wheel and the plastic and pop it off. These lug nuts are a 21 millimeter socket. I'm going to use that and a breaker bar to loosen them while the vehicle's on the ground. Raise this part of the vehicle. We're using a two post lift, but you can use a jack and jack stands. The lug nuts are loose. I’m going to take my socket and finish removing them. I’m just going to hold onto the wheel and take the last lug nut off. It's going to be loose. You don't want to drop it. You can drop the lug nut. That's okay. You just don't want the wheel to fall.
I’m going to disconnect the sway bar link from the strut. Going to spray some rust penetrant on this upper sway bar mount. Use a wire brush to clean off some of the rusty bits. These can be difficult to take off, they get rusty and then the ball joint spins. It does have a hex spot here to put in a six millimeter hex drive. A lot of times that strips almost instantly as soon as you try to break it free ad you end up having to put vice grips behind to grab onto the ball joint, because there's no point here for a wrench. We’re going to do our best to get this one off without having to cut it off.
So this is 17 millimeter nut. Try to break it free first. See, it's turning, it's turning the whole ball joint with it. It's really tight. I’m trying to clean out any rust and dirt that's in this hex drive so I can get the hex drive to sit as far possible inside here, so it doesn't strip. Use some brake parts cleaner, I've sprayed some oil in there and I've been working the hex drive in to try to clean it out. I can see it's going in a little deeper, trying to get this sit as best I can. That's as far as it will go. Spray some more rust penetrant on there. I'm going to try to counter hold this hex drive while I free it with the 17 millimeter boxed wrench. We'll see how this goes. Sometimes you have to brace that against like the strut ad these just have so much – see, it's moving. That's good. It's really tight, though, so I'm just going to put that there. I'm going to spray some more rust penetrant.
These are typically self-locking nuts, so they're a little bit, they're not perfectly round. They're kind of oblong and that can make removing them difficult and also the rust gets gummed up in the threads. So I'm trying to spin this on and off to try to work the rust penetrant into the threads. So as I kind of expected, working these back and forth this hex drive they basically always strip. It's nearly impossible to remove them without these stripping, no matter what you do. So the next step I'm going to get some vice grips and try to hold the ball joint back here and use a 17 millimeter socket and ratchet and continue to remove this nut.
I’m going to try to slide these locking pliers behind the ball joint on the sway bar link. I’ve got a 17 millimeter deep socket on this longer ratchet, going to try to remove these. It feels like it's turning. One thing to mention if you're going to have to remove sway bar links for any reason or think you're going to have to remove them for any reason, you should have new ones on hand. They're almost a one-time use part.
If you're as lucky as us, you'll have to resort to power tools or a hacksaw to cut these sway bar links free. I'll do my best to avoid the strut, I don't want to damage that. I just want to kind of cut on the – going to try to find the narrowest part of the ball joint and the sway bar link. I think I'm on there.
I've actually gone in here. Because these sway bar links get seized on here so easily, I went in and cut the boot away, the rubber boot. So that I can get locking pliers in here to get a better grip on it and it's kind of working by holding it. I'm able to turn the nut out. Worst case if I get loose enough and it just keeps spinning, then I will take a saw and cut it right here. But I'm going to keep trying it right now with the locking pliers. Got it.
Here are our old sway bar links from our vehicle. You can see where I had to cut them. I was able to finally get this one out, but still, these have been destroyed by trying to remove them and you can see they're kind of rounded here. There's no real way to counter hold them to remove the bolts. They are supposed to have a hex drive in here. That strips out pretty quickly when you're trying to remove them.
Here's a brand new sway bar link this is from 1AAuto.com. These actually have a six-point on them so you can put a wrench on here and tighten them down and it's not going to spin on you and when you want to remove them to do other services, you can put your wrench over here and spin this off without destroying the ball joint and the sway bar link. So this should fit great and work great in your vehicle.
Put these up. Get this one up top. You can bend these around. Slide it through. These nuts are locking nuts, so the hole is not perfectly round. It's kind of oblong. So when this starts to tighten it will lock and it won't want to back off.
These nuts are 18 millimeter get this one set up here. The counter hold on the back is 18 millimeters. I'm going to use a deep socket 18 millimeter in the front. Get these snugged down and I'll come back and torque them. Torque for these sway bar links is 55 foot-pounds, and repeat it on the other nut.
Reinstall our wheel. It’s important to note these lug nuts have a taper. Taper meets the wheel and matches the inside of the wheel. Don't install them on the flat side like this; that is incorrect. Install them with the taper to the wheel. It helps locate the wheel on the lug nut stud. I'm just using the socket and ratchet to bring these down snug before I put the car on the ground. Torque the lug nuts to 76 foot-pounds, going in a cross pattern. Reinstall the hub cap. You’ve got to line up the opening for the valve stem with the valve stem on the wheel. Just push it in place.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Torque Wrench
Rust Penetrant
18mm Wrench
17mm Socket
Jack Stands
18mm Socket
Safety Glasses
21mm Socket
Gloves
Wheel Chocks
Anti-Seize Grease
Ratchet
Floor Jack
Wire Brush
Swivel
1/2 Inch Breaker Bar
3/8 Inch Impact Gun
1/2 Inch Impact Gun
PSA55711
In Stock
Product Reviews
Loading reviews
4.80/ 5.020
20 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
19
0
0
0
1
fit good
timothy
July 13, 2018
timely delivered
great fitment
install was easy
customer was very pleased
Great product
T
November 2, 2018
Very good videos are also good would recommend this product
Parts fit great
ADA
November 5, 2018
I ordered the sway bar links and they were a great fit everything arrived on time and fast
Excellent prices and speedy shipping
L
March 6, 2019
I have ordered multiple parts from 1A auto and they have been terrific with everything. My last order I ordered two parts by accident though I only needed one and I contacted customer service and they corrected the order and refunded my double order with no return shipping needed thanks guys best on the net. Will continue doing business in the future.
Simple to install
N
August 25, 2019
Quick shipping and simple to install
Lutty
November 14, 2019
Product was the right choice for my car so I recommend 1A
Excellent service
M
January 29, 2020
Fast shipping and the parts fix perfect. I will highly recommend 1A Auto for any part you will need for your car.
just exemplary company over all
shawn
June 30, 2020
Finally I got an invite to give my reviews. Lots of good things to say about the company and service. Price is much cheaper than other places I looked at. Free shipment and parts arrived within 4 days. I found out I didn't need to replace these parts and offer to return them. After filling out the online return form, I was reimbursed the full amount. Better yet I didn't have to return the parts. Yup you heard me...I didn't have to return it to get a full refund. Even Costco can even beat 1A Auto return policy. I've ordered other parts from 1A Auto before and always satisfied with their service and parts. I also like the how-to video link relating to the parts I ordered. Just AWESOME !!!! My siblings have been raving about this company and the public should be as well.
Would recommend
D
July 28, 2020
It works great, fast delivery, great performance so far. Gets the job done.
Oscar
June 21, 2021
Good price. Would recommend. Great fit!!!!!!!!!!!! Happy with purchase
Jose
January 15, 2022
3 of the buts wouldnt screw had to use old obes
G
February 1, 2022
Was as expected
Thumps up
Derek
July 14, 2022
Good parts
2014 Avalon
Samuel
October 21, 2022
Solid components. Feel sturdy. In comparison to the factory ones they have a little more "body". Great construction.
Great products
kristopher
April 12, 2023
Great product strong and durable A1 Auto is always a great place to shop for me and the only place I put my trust in them and they never fail me??
GEMINIANO
May 22, 2023
fits perfetcn i replace all my swaybar links easy ti\o install
Danny
June 2, 2023
Great products
Buy with confidence
Arvind
January 14, 2024
Exact fit for my Camry. The car handles and steers better.
Strong materials
Jose
February 19, 2024
Love it 2009 Lexus es 350
OEM quality.
Javier
June 8, 2024
Sway bars were as describe by 1A auto. Perfect fit on my son Camry and easy to install.
My son stated it improve the car handling greatly.
Customer Q&A
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Toyota is a registered trademark of Toyota Motor Corporation. 1A Auto is not affiliated with or sponsored by Toyota or Toyota Motor Corporation.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.