Replaces
This part doesn’t fit a . Select from parts that fit.
Specify your vehicle's year, make and model to guarantee fit.
Part Details
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years.
Hey, everyone. Sue here, at 1A Auto. Today, we're going to show you on our '03 Volvo V70 how to do the front sway bar links. If you need this part or any other part for your car, click on the link below and head on over to 1aauto.com.
First thing we're going to do is remove the tire. I have weight on the tire of the vehicle still, so I can break the lug nuts free. This is a 19mm. I'm just going to break them free. Then we raise the vehicle up.
Now that the car is up in the air, I can remove the lug studs. This is what a European car does. There're not lug nuts because there's no studs on the hub, so it's a whole post. When you get to your last one, usually it's better to have both hands ready to grab the tire. I don't—like this one's frozen on there, but normally, the wheel will fall right off. So, just keep one of the lug studs partially threaded in and you break it free.
First thing we want to do is spray everything down. It is an '03—it's New England—so we're just going to hope that this helps with the removal. The sway bar link is an 18mm, and more than likely, it's going to spin in place. So, the Torx piece in the middle, here, is a T40—so we're going to have to hold that. I'm going to be going opposite on both ways. I'm going to pry up on this—on the nut—to break it free, and hopefully hold it still with my ratchet.
I can take that sway bar link nut right off and then push the link right out. Now we're going to raise the vehicle so we can get to the bottom. The nut on the lower part of the sway bar link is a 15mm wrench and the Torx bit is a T30. So, we're going to just pull opposite of each other. There is your front sway bar link.
Here we have the new sway bar link for our '03 Volvo through 1A Auto, and here's the one I took out. They're identical in length. They're both a sealed unit—non-greasable. There are two different-sized studs on these. The lower one is a smaller stud. They come with a locking nut, and the upper side is the thicker stud. They both come with new lock nuts with actual—looks like it has actual coating in there for locking—threadlock. So, if you need this part or any other part for your car, click on the link below and head on over to 1aauto.com.
Now we're going to install the new sway bar links. I'm going to fish it up through; make sure I go on the inside of the ABS cable, and there's that bracket in the back that holds the flex hose steel line. Just fish itself through—right through there. It's definitely easier if you put the top on first, so you can guide it all through. Now for the bottom. It doesn't line up. So, I have to use a pry bar. I'm just going to pull down on the sway bar itself so that the link can fall right in—just like that. Now I can put the nut on the bottom.
Now we're going to tighten the lower part of the sway bar link. The nut is a 15mm, but the inside is an Allen head, now—not a Torx bit. And it's an Allen 5—5mm. You put your wrench on and then take your Allen head, and just that—going the wrong way. My god. Here we go.
I did not find any torque specs for this, so I'm just going to snug it and know that that's lock nut, and that's on nice and tight. On the top part of the sway bar link it is an 18mm nut, so 18mm socket, 18mm wrench, but the center is an Allen—still the 5mm. I'm just going to use the wrench until the center bolt stud starts to spin. There is, like I said, no torque specs that I could find. I am truly just going to tighten that like that.
Before I install my wheel on my European car, I'm going to use the wheel stud pin set that 1A Auto supplies. It is, comes with two sets—a 12 by 1.5 or a 14 by 1.25. In this case, our Volvo is a 14 by 1.25.
I'm just going to put two of them in there. I'm not going to use all four. That way, when I pull the tire up, it has something to rest on. Anyone that's ever worked on a European car knows the frustration of trying to hold the wheel up and thread in a lug stud.
The neat thing about this is how it works. I just need to line up two of those studs. Now I can just walk away. It's the great part—getting my lug nuts—studs, I mean. And I can just take my time threading them in by hand, and it's not going to fall off.
Now that I've got three of the lug studs in there, I'm just going to tighten down—hand tighten tool so that the wheel is flat against the hub. Now I can remove my helping guide pins. You can just back those up. I think it's a must for your toolbox. These things are crazy awesome and it stops any frustrations. Now that I have them all hand tight, I can lower the vehicle down; put some slight weight on them and torque them.
Now we're going to torque the wheel. I've got the weight of the vehicle on the tire, and the torque for this Volvo is 103 foot-pounds. Like usual, I'm going to do everything in a star pattern. Okay, let's double check. Now that the repairs are done on the driver side, repeat the process on the passenger side.
Thanks for watching. Visit us at 1aauto.com for quality auto parts, fast and free shipping and the best customer service in the industry.
Tools used
Hey friends. It's Len here at 1A Auto. Today we're working on our 2004 Volvo XC90. This is the all wheel drive version. We're going to be replacing a left front lower ball joint. It's going to be super easy. I can do it. You can do it too. If you need this or any other part, you can always check us out at 1AAuto.com. Thanks.
Okay, friends. So just a quick note, we're going to be doing a lot of videos and replacing parts on this particular vehicle. So if you happen to notice in the video that you're watching, all of a sudden a part just is brand new and it wasn't brand new before, odds are we cut out. We were doing another job. We replaced that part. We cut back in and we're just showing you the stuff that you need to know to be able to do your particular replacement.
Okay, friends, so now what we're going to do is we're going to loosen up the wheel. I've got my vehicle supported from the ground, but the wheels still touching so that it can't spin while I do this. I'm just going to use my 19 millimeter. I have a thin wall socket on there so it can squeeze in between the rim and the lug nut. I'm just going to break it free.
That's a tight one. That's the reason for doing it while it's still in the ground. If you try doing this up in the air, the wheel of course is going to spin. Okay, so I've got three out of my five lug bolts out. This is what they look like right here. They screw directly into the wheel bearing. Once you take off this one right here, and then you go to take this one off, there's going to be nothing holding this wheel on. So you need to pay attention to that.
I'm just going to take this one lug here, lug bolt, put it in a couple threads. And that's just so the wheel won't be able to come off and potentially hurt me. Push my wheel up against, just grab it. I'm holding the wheel so it can't fall down at this point. Then we'll just grab it off and set it aside safely. So we're going to take off this lower ball joint nut right here. I'm just going to use a little bit of penetrant. Now I'm going to continue with my 21 millimeter socket and I'm going to remove the nut, safety glasses on hand protection of course.
Here we are. I'm just going to put it right on here just like that. Okay, so I'm going to use my tool here. I've got to pickle fork and I've got my small hammer. I'm just going to slide it in here like this. The purpose of the pickle fork is to essentially be a wedge. And it's going to try to wedge between the lower control arm and the upper part of the ball joint there, and hopefully pull the stud through the control arm. That's my plan.
Okay, I can see it moving. So we know we're going in the right direction here. We'll come over here. We have an 18 millimeter headed bolt. It goes straight up through and then on top. There's a 21 millimeter nut. So I'll just grab my air gun. I'm going to put my 21 up there. Maybe I'll come around from this side. It's a little bit easier to get to. Here we are. And safety glasses, blast away.
There's our nut. Here's our bolt. We'll set these aside. So now we're going to remove these bolts right here. 17 and a 17, that's going to hold in the forward part of the lower control arm. So once we break these free, there's a possibility that this could want to move and do whatever it wants to do. So just make sure you're safe. We've got our nut on here. If you don't have your nut started on there, just go ahead and do it for me please. That's just going to make it so when this does come free, if it does decide it wants to do something, we're going to have a point holding it so it can't fall down and hurt you.
That's what our bolt looks like. Here we are, both the same. We can set these aside. Alright, so let's get our ball joint nut off of here. Set that aside. Let's try to bring this down now. Here we go. Give us just enough room without pulling too much on this because we don't want to separate our axle, right? So we've got the ball joint out. I'm just going to try it out. There we are. Cool. All right, so now I'm going to come in here and I'm going to try to pry that out of there. Come right in between the subframe and the control arm. Here we are. So we're just going to remove these bolts right here. To do that we're going to use a 14 millimeter.
At this point, the only thing holding your ball joint into the knuckle, is just the fact that it's pressed in. It comes up inside this area right here. So to get it out it's going to be much more of a hassle than taking out these two bolts. We're probably going to use an air chisel. Come right along this corner right here, over here, over here, over here, over here, here, here, here, here, here. And then hopefully it'll come out. So I'm just going to come right down onto this lip right here and I'm going to try to air chisel down.
You could try to use something like a hammer and punch, whatever you've got. But the air chisel's definitely going to be my way of trying to get it to come out. I'm just going to give it a try. I've got my safety glasses, ear protection, hand protection. It's breaking free already. That's a really good thing. Super excited about that.
Okay, so I got it coming down from this side. I'm just going to come over here and try to get it to come down as straight possible so I don't mess up this hole. This side is much harder to get into with the angle of everything. Here we are. That came out a lot easier than I was expecting, so I'm super excited about that. There's our lower ball joint. Let's move along.
Hey friends, a quick product comparison for you over here. We have our front lower ball joint out of our 2004 Volvo XC90. We just took it out. It was super easy. And over here, we have our brand new quality 1AAUTO part. Both these ball joints are created the exact same. You've got the same mounting holes up along the top. You've got the splined area coming up along here. That's where it presses up into the knuckle. You've got your shaft area, comes with a brand new neoprene locking nut. And it even comes with brand new mounting bolts. With all that said, I don't see any reason why this wouldn't be a quality part to install into the vehicle. So I'm going to go ahead and do it. If you need this or any other part, you can always check us out 1AAUTO.com. Thanks.
So up in here is where the ball joint pressed up into. You can see where all the splines where. It's pretty nasty and cruddy up in there. So you can just use this brush right here, available at 1AAUTO.com. A little bit of parts cleaner, safety glasses of course, hand protection. We're using a chemical. I'm just going to blast this up in there. Use this little brush. Okay, so now we're going to use a little bit of copper never seize up inside this ball joint portion of the hole. We don't need to get it up inside there or inside there. Those are the two mounting holes. The brand new bolts came with brand new thread locker on it, so we definitely don't want to get never seize up inside the mounting holes. We just need it inside where the ball joints going to go.
Here we are. That looks pretty decent. So we'll just take our brand new quality 1AAUTO ball joint, our two brand new bolts that came with it. I'm just going to see if we can get this so what's going up in. I'm going to take my bolt. Just going to see if I can get it to thread in a little bit here. That's just going to help make sure that the ball joint's lined up for the next step, which would be essentially pressing this up and in here. There's going to be several ways we're going to do this. I'm going to snug these up, back and forth, back and forth. See if it'll will press up. When it seems like it's binding up, I'll just give it a couple loving bonks along the side here and just try to help it along.
We need it to go up as straight as possible so you don't just stay on one side, crank, crank, crank, crank, crank, tighten it up. So the whole thing's just going like this and then hope that you're going to do this side. You need to get it to go up as straight as possible. So I'm just going to use my 14. Can tell as I start to draw this up, it's starting to canter a little bit off to the side. So I'm just going to go over to this side just like that. This side. I know what you're thinking. It's crazy to keep having to go back and forth and I get that. But it's super important to just make sure that these are going one, two, one, two, back and forth to make sure this goes up straight.
There we are. So we're going to torque these down to 29 foot pounds. Just going to hit him one more time. Both of those are tight. Let's move along. Okay, so we cleaned up our three bolts here. We've got the thick one. The thick one goes through this, the hockey puck bushing. Then you have your other two that match up. They go through your subframe and then into the screw holes in the control arm. And then of course you got the ball joint hole over here, but that'll be the last thing that we do more than likely. So we'll put down the two bolts that we're not going to be using yet because I'm going to start with the hockey puck bushing. Let me see if I can get this to work its way in there. Just try to get it lined up.
Seconds just to get it lined up perfect, but once you do. All set here. Let's see if that's going in. It feels like it's going in. Make sure we get a couple of good threads going up through there. Oh yeah, I can feel it coming up through the top so I know it's definitely going up. All right. It's all the way up there. We've got our 21 millimeter headed nut. You could use some thread locker on these bolts if you'd like to. We'll say it's your prerogative. I'm going to use my other two bolts. I'm going to come through here. Should want to go right through. It's going to come through this side right into there.
You might have to just wiggle the control arm around a little bit. Here we are. Just going to snug these up using our 17 millimeter. So now we'll just snug up this bolt right here. We're going to use our 21 millimeter wrench on the top, on the nut side, and then an 18 millimeter right here on the bolt side. There we are. All right, let's grab the torque specs and move along. So we're going to torque these two bolts right here to 48 foot pounds with our torque wrench, with our 17 millimeter socket. Just going to hit him one more time.
Tight. So let's torque this a rearward bolt up. We're going to go 77 foot pounds. Once again with my 21 millimeter wrench up top there, I got my 18 on the bottom here. Alright, I'm going to hit it one more time. Tight. And those two are tight. Let's move along. So now what we're going to do, because we can't obviously lift up on this with a strut holding it down to be able to get the control arm over the ball joint stud, we're just going to create a little bit of slack here for the ABS cable.
To do that, I'm just going to grab right here and try to roll it out of here. Just going to try to grab it, get it out of there. We want to make sure we have plenty of slack because what we're going to do is we're going to take out these two nuts, take the bolts out, and we're just going to lift up on the knuckle a little bit. Drop the ball joint, stud into the lower control arm, and then remount all this. It's going to be pretty easy. This just rolls out of here.
Now we've got plenty of slack for in case, God forbid, something happens. Something to remember once we get these out is that we still have the axle attached to the knuckle. And of course the outer tire rod end and stuff and the hose. But anyway, so when you're moving the knuckle around, you want to be careful not to pull too far out because you could separate your axle boot right here. There's a joint in there and there's one up in the outer portion of the axle as well.
So if you pull too far, you could separate it and cause yourself some axle issues down the road, which would be bad. We'll use a 21 and an 18. I'm going to use my 18 wrench to hold it. My 21 on my air gun, safety glasses on hand protection. That's what our nut looks like. That's what the bolt looks like. Let's put them both together. Same thing for this one. Okay, so once I take this out, what's going to be holding it in? The axle and a couple other really not very strong things, so just keep that in mind. All we want to do now is just lift this up and get the ball joint stud, which is right here, to go into the control arm hole, which is up a little higher. There we are. Let's see if I can get this. There we are.
There we are. Get this bar out of here. I used the bar to pry down on the lower control arm and then brute strength to lift up on the knuckle. Now that it's in there, we can continue by relining everything up here. I'm so close. Here we go. Once I get the lower bolt in here, I'll be able to do whatever I want with it. It's just a getting things situated. It's the hardest part here. There we go. It's going in. My bar out of here.
Well, that part right there is going to be your test. I'm sure you can do it. Give it a bonk. There we are. It's your prerogative if you want to use a little bit of thread locker on these. For the purpose of this video, I'm not going to worry about it. I'm just going to go right on here. All right, let's move ahead to the next step. So we're going to take our neoprene locking nut. Just start it right on here. We're going to use our 21 millimeter and I'm just going to bottom this out. Then we'll go ahead and torque it down.
Let's torque it. So here we go. We're going to go ahead and torque this down to 74 foot pounds. There it is. I'm going to hit it one more time. We know this is tight. We know these two are tight. These two are tight, and this is tight. We know that those up there are tight. Everything's tight. Let's move along to the next step. I'm just going to snug this up to 77 and then we'll continue on to the second step. 77 foot pounds, by the way, not inch pounds. Big difference.
There we are. Break it free. This one. There we are. So now, I'll leave that on there, we're going to do, we're going to use an angle gauge and we're going to bring it all the way to 90 degrees. So I'll put this up here and I'll put this kind of like this. I'm going to bring it over. Set it up against here so what's resting. Now I'm going to use my ratchet. I'm going to try to bring this around at 90 degrees.
Here we are. Get my tool out here. Cool. I want just a little bit past because when I first started, the wrench was turning. I zoned holding onto it. So anyway, we'll do the same to the lower one and then off we go. Now that we have those both torqued, we'll get our ABS wire back on here. Just going to slide it through like this, just kind of roll it as I push. IT should want to slide right in. This one right here. I'm going to come from the back side. Get it up on there. Now I'm going to roll it, slide it right in. Give them a nice little tug. Those are going nowhere. We know our abs wire is secured. We can move along to the next step. Okay, so that was a really fun job. We got it all done and we got everything torqued down the way it's supposed to be.
The only thing that's left to do of course is to get the wheel on and get that torque down and of course drive it down the road and make sure everything feels good. Lastly, make sure you get your alignment. Other than that, great job. Down the road, you go. Okay. So now to make it easier to get the wheel up on here where we don't have the lug studs that are sticking out and you put your wheel up on. It just kind of holds the wheel nice and easy for you, you don't have to stand there and hold it forever.
Volvo decided to make it fun and interesting and make you work your muscles a little bit. Well 1A Auto sells this awesome tool. Basically all these are is they're going to give you a lug stud so when you're putting your wheel on, you just slide your wheel right over this and it's going to hold it there so you don't have to sit there and try to muscle at the whole time while you try to line up the holes and put your lugs stud in, or lug bolt. So I'm going to set that aside. I'm going to grab my wheel, bring it right over.
Hold on to one of my lug nuts. Just going to bring this up. Slide it right over that. Boy oh boy, that made it easy. So now we just take our lug bolt. Put our wheel up against there. Start this in hopefully. I should've grabbed one of my sockets. It would've made my life a little easier here. There we are. And even though I was holding the wheel steady that whole time, I didn't have to have my whole body holding it, try to line it up while I'm staring into the hole and put this through. Thank you 1A Auto. So we'll just start all these lug nuts in and then we'll bottom them out, torque them down.
Okay, we've got all the lug nuts bottomed out. Now we'll just bring the vehicle back down so the wheel's touching the ground but without full force of the vehicle's weight on the wheel. And then we'll torque down these lug nuts. So here we are friends, we've got our torque wrench out. It's set to 103 foot pounds. I have my thin wall, 19 millimeter socket because there's limited space to get in between these lug bolts and the wheel. When we tighten these down, we're going to go into star pattern here, here, here, here, here. And then if we decided to go around again, we'll do the same thing.
But anyway, the reason for going in a star is essentially, so as we're going around, if the wheel's cantered it a little bit, it won't get stuck that way. And maybe the torque wrench thinks it's torquing it down to 103 like it's supposed to be, but it's a little bit cocked off to the side. Then you drive down the road, hit a bump or whatever, everything starts loosening up, your lug bolts come out. Long story short, just tighten them in a star pattern. There we are. I always like to go around twice. It doesn't cost me anything. It doesn't hurt me any and it's small price to pay for safety. Okay, all torqued up. Great job everybody.
Thanks for watching. Visit 1AAUTO.com for quality auto parts shipped to your door, the place for DIY auto repair. And if you enjoyed this video, please click the subscribe button.
Tools used
Hey friends, it's Len here at 1A Auto. Today we're working on our 2004 Volvo XC90 and we're going to be doing front sway bar links. It's going to be very simple. I can do it. You can do it too. If you need these or any other parts, you can always check us out at 1aauto.com thanks.
Okay friends, so just a quick note, we're going to be doing a lot of videos and replacing parts on this particular vehicle. So if you happen to notice in the video that you're watching, all of a sudden the part just is brand new and it wasn't brand new before odds are we cut out, we were doing another job, we replaced that part, we cut back in and we're just showing you the stuff that you need to know to be able to do your particular replacement.
Okay friends, so now what we're going to do is we're going to loosen up the wheel. I've got my vehicle supported from the ground, but the wheel is still touching so that it can't spin while I do this. I'm just going to use my 19 millimeter. I have a a thin wall socket on there so it can squeeze in between the rim and the lug nut. I'm just going to break it free. It's a tight one. That's the reason for doing it while it's still on the ground. If you tried doing this up in the air, the wheel of course is going to spin.
Okay, so I've got three out of my five lug bolts out. This is what they look like right here. They screw directly into the wheel bearing. So once you take off this one right here and then you go to take this one off, there's going to be nothing holding this wheel on, so you need to pay attention to that. I'm just going to take this one lug here, lug bolt, put it in a couple threads and that's just so the wheel won't be able to come off and potentially hurt me. Push my wheel up against, just grab it. I'm holding the wheel so it can't fall down at this point and we'll just grab it off and set it aside safely.
So here we go, friends. Let's go ahead and take this nut off right here. We're going to use our 19 millimeter socket. I'm going to use a half inch air gun. It's going to make it much easier than trying to turn it with a ratchet. I've got my safety glasses and my hand protection of course. This loosened up quite a bit. What I'm going to do now is I'm going to try and get back here and I'm going to see if I can get some locking pliers in to hold the stud because as I try to turn the nut, it's just spinning the stud. I'm not sure if these will get in here. I like to have these as tight as possible. Odds are, it's still going to spin. I'll probably have to readjust it, but... Looks like it is started a little bit more
So I just grabbed different locking pliers here. Just going to see if I can get this as tight as possible. A little bit at a time apparently. That's just the way it wants to go. I don't even think I can get these things tighter than they are. If you wanted to, you could try to apply a little bit of heat. The problem with that is that you don't want to apply heat to the strut itself. So I mean, if you're over here blasting away trying to heat up this nut, I mean I guess if you came across the edge here and you were nowhere near this part, you might be able to get away with it. It's just risky business, because inside here is pressurized gas. So I'm going to try everything I can without heat first and we'll see what we have to do when we have to do it.
It really doesn't seem like anything good is happening at this point. I'm going to try to tighten this up, which might seem like it's counterintuitive, but once I get it tight and then re-blast it out, hopefully just the speed and the inertia and everything moving, it'll pull its way right off. Just give it another blast with this stuff. So I'm going on now. And nothing's happening. Okay.
So I just applied a little bit of heat. I tried to go right along the edge here and just try to catch the edge of the nut. Once again, like I said, I was trying not to hit up against the strut itself. It's a pressurized gas unit. So we got that nut off of there. Get our tool off of here. Bonk, bonk. There's our lovely sway bar link end there. What was given us all the trouble is when we were trying to squeeze on here, it was just literally spinning in the grips. It's very common.
So I'm going to be preemptive with the heat on this one, because I know that the upper side needed a little heat, and I have nothing to worry about here as far as my heat's concerned. The abs wire and everything is super far from this area. The closest thing we have is just the axle boot. So I'm not going to heat going in this direction. I'm trying to spray that way. It's going to go right over here and there's literally nothing around here that I have to worry about except for maybe the bellows boot, but that's pretty far away. The nut on the lower side of this, that we're doing right now, is actually a 17 millimeter, which is different than the upper nut. I don't know why Volvo did that. I'm sure they have their own reasons. I'm no engineer. Just lowly old Len. Let's see if we can get this to come off. Get our safety glasses on. Okay, it's getting loose. Locking pliers in here. Hooray. Here we are. Got that sway bar link out of the way.
Here we are friends, a quick product comparison for you. Over here we have our front sway bar link out of our 2004 Volvo XC90. We just removed it, and over here we have our brand new quality 1A Auto part. This comes with brand new nuts. These are locking nuts. The studs come in the exact same as the originals. Where up on top, the studs a little thicker and on the lower part, the stud is skinnier. That's why we had a bigger nut and a smaller nut. It's important to take note that the length of them is the same. That's super important. Obviously you don't want to have one that only kind of goes that far. Anyway, it comes with brand new boots. Like I said, brand new nuts. It comes with everything you need to mount. I don't see any reason why this wouldn't be a quality part to install into the vehicle, so I'm going to go ahead and do it. If you need this or any other part, you can always check us out at 1aauto.com. Thanks.
Okay, so we've got our sway bar link. We'll put it up in here, like this. This is the smaller side, the side with a small stud. Okay. You can get that started. Now we're going to blast this on with a 15 millimeter socket. We've got our 15 on our half inch gun with some safety glasses. Tight. All right, so it's important to make sure that we have our ABS wire going along the outside of your sway bar link. You don't want it heading towards the inside there and getting all pressed in there and whatever. So if you notice it doesn't really want to line up very well, you can just do something as simple as taking your pry bar, go up against the sway bar and then anywhere you can find to pry up against. And you don't even need to really go very far. Just like that. It's lined up so it's straight. I'm going to take my 18 millimeter socket. Let's see if I can get it on here. There we are.
Now I'm just going to blast it on. Of course not. We're going to try it one more time. I'm going to try it a little bit more gusto, and I'll leave it so it's just barely on there. Then I'm going to blast it. And that's a no. Okay. So I put some locking pliers on here. I'm going to be careful not to damage my brand new boot, and we're just going to go ahead and try to blast this on. There we are. So now that we finished up that job, what you would do is you'd go over to the other side of the vehicle, assuming you're doing the same thing on the other side, repeat the same procedure, easy peasy. Grab your wheels, put them on, torque them down, down the road you go. Easy peasy.
Okay, so now to make it easier to get the wheel up on here where we don't have the lug studs that are sticking out and you put your wheel up on and it just kind of holds the wheel nice and easy for you. You don't have to stand there and hold it forever. Volvo decided to make it fun and interesting and make you work your muscles a little bit. Well, 1A Auto sells this awesome tool and basically all these are is they're going to give you a lug stud. So when you're putting your wheel on, you just slide your wheel right over this and it's going to kind of hold it there so you don't have to sit there and try to muscle it the whole time while you try to line up the holes and put your lug stud in or lug bolt. So I'm going to set that aside. I'm going to grab my wheel, bring it right over.
Hold on to one of my lug nuts. Just going to bring this up. Slide it right over that. Boy oh boy that made it easy. So now we would just take our lug bolt. Put our wheel up against there. Start this in, hopefully. I should've grabbed one of my sockets. That would've made my life a little easier here. There we are. And even though I was holding the wheel steady that whole time, I didn't have to have my whole body holding it, trying to line it up while I'm staring into the hole and put this through. Thank you 1A Auto. So we'll just start all these lug nuts in and then we'll bottom them out, torque them down.
Okay. We've got all the lug nuts bottomed out. Now we'll just bring the vehicle back down so the wheel is touching the ground, but without full force of the vehicle's weight on the wheel. And then we'll torque down these lug nuts. So here we are friends. We've got our torque wrench out. It's set to 103 foot pounds. I have my thin wall, 19 millimeter socket because there's limited space to get in between these lug bolts and the wheel. When we tighten these down, we're going to go in a star pattern. Here, here, here, here, here, and then if we decided to go around again, we'll do the same thing. But anyway, the reason for going in star is essentially, so as we're going around, if the wheels cantered a little bit, it won't get stuck that way and maybe the torque wrench thinks it's torquing it down to 103 like it's supposed to be, but it's a little bit cocked off to the side. Then you drive it down the road, hit a bump or whatever, everything starts loosening up. Your lug bolts come out. Long story short, just tighten them in a star pattern.
There we are. I always like to go around twice. It doesn't cost me anything. It doesn't hurt me any, and it's a small price to pay for safety. Okay, all torqued up. Great job everybody.
Thanks for watching. Visit 1aauto.com for quality auto parts shipped to your door, the place for DIY auto repair. And if you enjoyed this video, please click the subscribe button.
877-844-3393
Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET
Specify your vehicle's year, make and model to guarantee fit.
This part doesn’t fit a . Select from parts that fit.
If your vehicle isn't listed, search Steering & Suspension Kits
If your vehicle isn't listed, search Steering & Suspension Kits