WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Tailgate Handle Bezel 1999-2006 GMC Sierra
How to Replace Tailgate Handle 1999-2006 Chevy Silverado
How to Replace Tailgate Latch Rod Clips Chevrolet Silverado 1500 1999-2006
How to Replace Tailgate Handle Bezel 1999-2006 Chevy Silverado
How to Replace Tailgate Handle Bezel 1999-2006 Chevy Silverado
Created on:
Tools used
1/2 Inch Wrench
Razor Blade / Gasket Scraper
1. Remove the tail gate handle
Push down and out to unclip the tail gate handle bezel.
Remove the three bolts on the back of the tail gate.
Use a razor blade to cut through the rhino-liner to access the bolts.
Remove the door handle by unclipping the handle latch rods.
2. Install the new tail gate handle
Add some white grease to the hinges in the handle.
Clip the latch rods in.
Bolt the tail gate handle back in using your wrench.
Clip the tail gate handle bezel back in.
Brought to you by www.1AAuto.com. Your source for quality replacement parts and the best service on the internet.
Hi I'm Mike Green. I'm one of the owners of 1A auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my twenty plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1aauto.com. The right parts installed correctly, that's going to save you time and money. Thank you and enjoy the video.
In this video we'll be doing a tailgate handle on a 2004 GMC Sierra. Same as any 99-06 Sierra Silverado. Only tools needed are a half inch wrench and an Exact-o knife if you have a Rhino liner in your truck. Also if you're going to order the tailgate handle we do recommend ordering the bezel as it's kind of difficult to get off without breaking it and actually we found on our truck it had already been broken. So it'll just save you a little time.
Okay, so to remove your tailgate handle the first thing you want to do it is remove this bezel. Basically there are two pins that go down and then it clips in. So you want to push down on top and then pull out, this is interesting. This truck has already been damaged and somebody used two sided tape to put it in there. See the close up, the tabs are broken off. It commonly happens. Two sided tape is okay for awhile, the problem is what happens is these trucks, the dirt just kind of swirls up and around here and sooner or later the two sided tape is going to let go and this thing's going to look like that.
Here on the tailgate you've got three bolts, you can see ones already loose because I was experimenting a bit. This truck's got a Rhino liner in it and a lot of trucks do now. If you don't obviously you can just take these bolts off but if you do have a Rhino Liner you want to use a knife and you just basically want to cut very carefully, so you don't cut your fingers off, cut each hex. I'm trying to do this quick. If you don't cut this off you won't be able to get your wrench on there. You could probably force your wrench on there but this is the best way not ruin your bolts. Just kind of back it in there and peel it off. You don't have to get it all off, it doesn't have to be perfect but you definitely need to get enough off so that you can get your wrench on there. Okay it's a half a inch, you push down and the bolt comes up and out. You want to remove these three bolts.
As I was taking these out I wasn't filming because you don't really need to see me tearing out but something funny, this has washers and the Rhino Liner has actually trapped the washers in there but that's okay. You can just remove it to that point and you'll still be able to remove your handle. You just back it out and you can hear my handle just dropped down there's. We're going to put our bolts on our 1A Auto magnetic tray.
Okay here's your handle and there's two rods right here held in by clips and basically you just need to move these clips down. Okay and the rod pulls out and then there's your tailgate handle. New handle, see it's all basically the same as the old handle. Okay what you want to do always, is lubricate. Any point where it might pivot, spray them with a bunch of stuff. Put it in here and it'll attach. This goes that way. Push them in. Push these rods into the clips. They don't want to go easily, there's it goes, it's kind of working in a little bit. You basically do it one side at time, just kind of grab the rod, push on the tailgate. Grab this rod, push on the tailgate and it'll open up.
Okay then down here and we'll take the handle and we can line it up by and I'll need my wrench here. These washers are kind of stuck in here. Get that bit with no problem. The last one here. As far as tightening, it doesn't have to be incredibly tight. Holding it with my fist, and that's good. So we have our new bezel here and here's the old one, you can see the little teeth that are broken off. Remove some of the two sided tape because it needs to bite under the metal and that will just get in the way. Basically this just goes in. Push down on it and there you go all set.
This video was brought to you www.1AAuto.com. We hope we helped you out. We are your source for quality replacement parts and the best service on the internet. Feel free to call us toll free 888-844-3393 we're here for you on the internet and in person. Thank you very much.
Tools used
13mm Socket
Flat Blade Screwdriver
Ratchet
Trim Tool Set
First things you're gonna wanna do is make sure that your tailgate is down. Once you have it open and down, you're gonna see these three bolts right there. Remove those using a 13-millimeter socket. It's nice and tight. All right. Let's get these out of here. Wiggle this handle around, so it's nice and free. With this black bezel, the next thing you're gonna wanna have is one of these nice plastic trim tools. The reason why we're gonna use plastic is because we're gonna come in between the bed and the plastic shroud right here. Just go ahead and come right here. Push it. Do the same thing right there. Once you have the top broken free, just go ahead and lift this straight up and draw it away.
Go ahead and come in between here with a nice flathead screwdriver. Pull that clip down. Grab this rod, and slide it out. Do the same to the other side. Let's go ahead and get the handle out of here. Let's go ahead and get this handle in here. Weasel it in. There we are. Now, you're gonna grab your connecting rods here. Slide it in, and then lock it down. Slide it in. Bring this around. Lock it in. Give it a nice shake. Do the same to the other side.
So, now with this nice and loose, we can continue on to installing this. If you were to pay attention, on the backside, you're gonna see that you have a couple little pitons. And then, right here, you have some hooky-dos. When you go to install this, you're gonna put the bottom in first, so that the pitons go down into here. They'll latch in, and then just roll it in, and it'll latch. Just like this. In.
So, now from inside the bed, you can see the backside of the tailgate. We're just gonna kinda wiggle the handle around until we can see our bolt holes. Grab your bolts. Go ahead and start all three of them in before you tighten any of them down. Let's go ahead and snug them up. Let's give it a test. Perfect.
Tools used
13mm Socket
Gloves
3/8 Inch Drive Ratchet
Safety Glasses
Tools used
13mm Socket
Ratchet
Trim Tool Set
First thing you're going to want to do is make sure that your tailgate is down. Once you have it open and down, you're going to see these three bolts right there, remove those using a 13-millimeter socket. Nice and tight. Let's get these out of here. Wiggle this handle around so it's nice and free. With this black bezel, the next thing you're going to want to have is one of these nice plastic trim tools. The reason why we're going to use plastic is because we're going to come in between the bed and the plastic shroud right here. Just go ahead and come right here, push it, do the same thing right there. Once you have the top broken free, just go ahead and lift this straight up and draw it away.
We can continue on to installing this. If you were to pay attention on the backside, you're going to see that you have a couple little pitons, and then right here you have some hooky-dos. When you go to install this, you're going to put the bottom in first so that the pitons go down into here, they'll latch in and then just roll it in and it'll latch. So with this, in. So now from inside the bed, you can see the backside of the tailgate, we're just gonna kind of wiggle the handle around until we can see our bolt holes. Grab your bolts, go ahead and start all three of them in before you tighten any of them down. Let's go ahead and snug them up.
Tools used
13mm Socket
Ratchet
Trim Tool Set
First thing you're going to want to do is make sure that your tailgate is down. Once you have it open and down, you're going to see these three bolts right there, remove those using a 13-millimeter socket. Nice and tight. Let's get these out of here. Wiggle this handle around so it's nice and free. With this black bezel, the next thing you're going to want to have is one of these nice plastic trim tools. The reason why we're going to use plastic is because we're going to come in between the bed and the plastic shroud right here. Just go ahead and come right here, push it, do the same thing right there. Once you have the top broken free, just go ahead and lift this straight up and draw it away.
We can continue on to installing this. If you were to pay attention on the backside, you're going to see that you have a couple little pitons, and then right here you have some hooky-dos. When you go to install this, you're going to put the bottom in first so that the pitons go down into here, they'll latch in and then just roll it in and it'll latch. So with this, in. So now from inside the bed, you can see the backside of the tailgate, we're just gonna kind of wiggle the handle around until we can see our bolt holes. Grab your bolts, go ahead and start all three of them in before you tighten any of them down. Let's go ahead and snug them up.
DHA30167
In Stock
Product Reviews
Loading reviews
4.68/ 5.025
25 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
22
1
0
1
1
Replacement
D
February 5, 2018
Everything was just as it was advertised, it fit perfectly and the installation was easy
Tailgate latch silverado
Don
June 19, 2018
Parts arrived quickly and fit was great. So easy for installation - can't believe I put up with a broken tailgate latch for so long- if I had know that the fix was so easy and affordable, I would have made the repair right after it broke!
Better than expected
J
September 15, 2018
Was pleasantly surprised with my purchase. Was delivered as promised. The handle came with the clips already attached so I didn't need the clips that I ordered. Oh well, I'll have a set if I ever need them. So easy and inexpensive, not sure why I see so many tailgates without handles.
2002 GMC Pickup
Phyllis
October 14, 2018
Parts was just what I needed to replace the tailgate handle. Video was very helpful to when replacing. Thanks
Perfect Repacement Part
J
December 3, 2018
I ordered this to repair my broken tailgate latch. It came in quick and was easy to install. Works great!
fits perfect
K
December 27, 2018
This bezel set was for an 07 classic body style chevy PU. The new parts fit the tailgate exactly as the factory pieces did. The installation was easy. It took less than 10 minutes to complete the job.
Silverado tailgate handle
D
January 13, 2019
My 17 yr old handle snapped off. Ordered a new handle and bezel from 1AAuto. Watched the how to video and my tailgate was replaced in no time. Parts were a perfect match.
Tailgate handle
Anita
March 20, 2019
Get response fast shipping. Will definitely use your company again. Thank you
Tailgate Handle
T
March 20, 2019
When I got my new tailgate handle, watched the youtube video. Real easy install, no problems, as good or better than a cChevy part, at a lot less money. Thanks
David
April 6, 2019
Quick shipment. Perfect fit for my truck. Looks good
Great Value
B
April 25, 2019
Good price, high quality, perfect fit, fast delivery. Had everything I needed to get this tail gate working like new. If you only think you need 1 or 2 of these parts, do yourself a favor and buy the whole kit.
Replacement latch right on
J
January 12, 2020
First time purchase part is exact replacement and instructional video was perfect. Highly recommended source for auto parts
David
April 9, 2020
the product was what I it can't get no better then this.
T
June 16, 2020
Part was exactly as described, got here quickly, went in just like it was supposed to and they had a video with tips about removal and install. What more can you ask for? I thought the price was fair too.
Tailgate handle and bezel set
G
August 6, 2020
Parts arrived earlier than expected. Their fit was excellent and install was just as eady as shown on the video.
Thank you 1aauto.
Nacona
January 7, 2021
Wasnt too satisfied with the bezel because the top clips that hold it in place broke like every other bezel I gotten. As far as the tailgate handle it fit perfectly
Don
September 25, 2021
Item is working so far
tailgate
Daniel
January 27, 2022
handle was perfect fit nicely but the plastic bezel broke instantly had to order a second one but have not put it on yet
Perfect fit
Michael
June 2, 2022
Easy to remove the old handle and replace it with the new one. Fit and finish were great.
Michael
September 17, 2022
Retention clips are very weak quality of product is low.
A1 Auto is a good company but the quality of this product is below their standards.
Sean
October 21, 2022
Straight up, as usual OEM fitment without the dealership prices or bullshit! Love these people, cant give them enough credit!!
A 5 star rating.
Ken
December 4, 2022
Fast delivery. Easy to install instructions. (1/2 hour). Will definitely use 1aauto again.
If your tailgate flies open when you hit a bump, buy this item
Patrick
January 26, 2023
Perfect fit, easy install, didn't need the extra plastic clips, but am glad I had them, just in case.
paul
March 14, 2023
Works great
Clarance
February 23, 2024
shipped very quickly and was an exact fit ,took minutes to install thank you .
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
GMC is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by GMC or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.