Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Sway Bar Link 2003-07 Honda Accord
Created on:
Tools used
Socket Extensions
Locking Pliers
14mm Socket
15mm Socket
Jack Stands
19mm Socket
Ratchet
Floor Jack
1. Removing the Wheel
Partially raise the vehicle with the wheel still contacting the ground
Loosen the 19 mm lug nuts
Raise and support the vehicle on jack stands
Remove the lug nuts
Replace one lug nut loosely
Hammer the tire from the back side if the wheel is stuck
Remove the last lug nut and the wheel
2. Removing the Front Sway Bar Links
Remove the 14 mm lower end link nut, holding the stud with locking pliers if it is spinning
Remove the 14 mm upper end link nut, holding the stud with locking pliers if it is spinning
Remove the sway bar link
3. Installing the Front Sway Bar Links
Insert the upper sway bar link into the sway bar and thread the new 15 mm nut onto it
Insert the lower sway bar link into the lower control arm and thread the new 15 mm nut onto it
Tighten the nuts, carefully using locking pliers, or a hex wrench, if the studs spin
Torque the sway bar link nuts to 22 ft-lb, if able
4. Installing the Wheel
Slide the wheel onto the lug nuts
Replace the lug nuts and tighten them in a star pattern
Lower the vehicle with the wheel lightly touching the ground
Torque the lug nuts in a star pattern to 80 ft-lbs
Lower the vehicle completely
Hi. I'm Mike from 1A Auto. We've been selling auto parts for over 30 years.
Hey, everyone. Sue, here, from 1A Auto. Today, we have an 07 Honda Accord in our shop, and we're going to be showing how to remove and install the front sway bar links. If you need this part or any other part for your car, click on the link below and head on over to 1AAuto.com.
19 millimeter socket to loosen up the lug nuts. Now I'm going to raise and support my vehicle with my two post lift. You can use jack stands with a jack. Now we're clear to remove the tire.
14 millimeter wrench, I'm going to break that nut free and then of course it's going to spin. So I'm going to have to hold the inner part of it. There is an Allen head right here, but there's no way I can get there from that wishbone. I can do it on the top one, but not on the lower. So I'm going to have to hold the inner piece of metal with a pair of locking pliers.
Make sure you can get your wrench out. There we go. I'm going to remove the upper swivel link to the sway bar. 14 millimeter sock wrench again. See how much we can get before it starts to spin. It's spinning. Okay, so we'll put some locking pliers on the back just like I did on the bottom. See if I can hold that firm.
Wonderful. Now we can remove the sway bar link from the actual linking control arm. I'm going to just take a pry bar and see if I can pry that free.
To install the front sway bar link, it's just basically two reverse procedure. I like to put the sway bar link into the top of the sway bar first. The new nuts are a 15 millimeter, not a 14. It still has the Allen head in the center, which is a five millimeter Allen head.
Now I'm going to put the lower one in. Start the nut. With the wishbone in the way, I have found that it's kind of difficult to put an Allen head in there and hold that. So you're going to have to use a pair of the needle nose vise grips like I did to remove it just being careful, not pinching the new boot, using a gear wrench, ratchet wrench. I'm going to snug that pretty much as tight as I can get it because I'm going to end up torquing it.
Now I'm going to start the bottom. Put a pair of locking pliers on there, needle nose locking pliers. See if I can catch it without pinching that boot as careful as I can be. I'm going to put a longer wrench on here to tighten this because obviously I can't get a torque wrench in there. The specs for this is 22 foot pounds.
Now I can put a torque wrench on the top. So we're going to torque this to 22 foot pounds. Okay. Now we're ready to put our wheel back on. I'm just going to snug them up by hand then I'll lower it down on the ground with the weight of the vehicle on it and I'll torque the wheel to 80 foot pounds.
19 millimeter socket, and we're going to torque the wheel to 80 foot pounds in a star pattern. Double check. Now we're going to repeat the process on the other side.
Thanks for watching. Visit us at 1aauto.com for quality auto parts, fast and free shipping and the best customer service in the industry.
PSA67824
In Stock
Product Reviews
Loading reviews
There are no reviews for this item.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.