Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
If your vehicle's equipped with a locking lug nut, you're going to want to have it ready. Get it to fit on there. These are 19-millimeter. Take our breaker bar, we'll loosen them up, about a half turn. Once you've loosened your lug nuts, raise and support your vehicle. We're going to use a lift for this, so to make it easier for you to see what we're doing, but you can do this on jack stands in your driveway. These are pretty loose now. Going to take my socket in my hand and undo them with my hands. I'm doing the last one. Just make sure you've got hold of the wheel. It might come loose. This one came off pretty easy.
To remove the rear swear bar link, there's a nut here at the bottom and a nut here at the top. There's an Allen key in here to counter hold it once it's loose on both ends. There should also be a keyway behind here to hold it. I will start by spraying with some rust penetrant. Spray both of them, and use a 14mm socket and a breaker bar. Since this one doesn't have a key way on the back to hold it, I'm going to put my 14mm wrench on and use a 5mm Allen key on the end of my breaker bar. Put it into the sway bar.
The inside of this is stripped, which can often happen. There is no keyway on the back of this to hold with a wrench, so I'm going to use some locking pliers and break the top one free. This one is now stuck, so I'm trying to get the top one free and then pop it off the lower ball joint and try and get it off that way. The 5mm part of this one is also stripped out. I was able to get some locking pliers in here. I got my 14mm wrench, and I'm going to keep spraying it with some rust penetrant. I'm going to work it back and forth to get the nut free, because there's a lot of gunk on the threads. Just kind of go back and forth, back and forth. Then slowly loosen it.
If it starts to get tight, just kind of go back. I'm going to switch to a ratcheting 14mm, because we're getting pretty close. Got that one loose. With this top one loose now, the sway bar links are basically just a ball joint. I'm just going to take it and just sort of force it off. Now I can get in here. Once I take this rubber boot off, and you can see the ball joint that's in there. Now I can get in there with some locking pliers and really grip on that, and work on getting that bottom nut out. So I just popped it out of the socket here, and took the boot off with it. The break line in here. I'm going to hold it up against the spring, get the 14mm ratchet and work it back and forth. I finally got it loose; take it off with my fingers and we'll pull it out.
Here's our old sway bar link from the vehicle. You can see it came apart as we were trying to remove it and that can happen. Boot was ripped. It doesn't have any way to counter hold this other than the Allen head key, which is stripped on both ends. So I used some locking pliers on it, and just worked the nut back and forth to get it off. Then eventually you've got one side off, and just pop the other side out. That's the easiest way to remove it.
As you can see, it's virtually identical the new one 1aauto.com. These are driver's side and passenger side specific, so you'll need to make sure you have the correct one for whichever side you're doing, or if you're doing both.
Just make sure that you use the correct one for the passenger side and the correct one for the driver's side, because they'll only fit one way. It comes with new nuts. You can see that Allen key socket to counter hold it; we'll use that when we're torquing it.
Get your new sway bar link, and insert it in the bottom. Put the nut on. Insert it in the upper part, this is the sway bar. Bend those a little bit if you have to. Then just a ball joint in there to move around. Got to find the right spot. Our replacement nuts are 15mm, so we'll use a 15mm ratcheting wrench, and a 5mm allen key to hold them. Then work on the upper one; again, put the allen key in to counterhold it. I'm just going to tighten this as tight as I can go.
Reinstall the wheel. Put the lug nuts on by hand. 19mm socket ratchet, I'm going to snug these lug nuts. Torque wrench set to 80ft/lbs. Torque your lug nuts in a star pattern.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Tools used
