Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Direct Fit - No vehicle or wiring modification necessary
DOT, SAE, and FMVSS Compliant - Meets on-road use regulations
Matching set for a restored look
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How To Replace Side Marker Light and Bulb 2004-11 Mazda 3
Created on:
Tools used
Flat Blade Screwdriver
Phillips Head Screwdriver
1. Removing the Side Marker Light
Remove the three clips on the back side of the front wheel well.
Remove the one screw near these clips.
Reach behind the inner fender and release the clip.
Reach up into the inner fender and push the tabs on the backside of the side marker light to release it.
Pull the light forward and disconnect the wiring harness.
2. Reinstalling the Side Marker Light
Plug in the wiring harness.
Push the front end of the light in first then the back to snap it into place.
Put the inner fender back into place.
Insert the clips.
Insert the screw.
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet.
Hi, I'm Don from 1AAuto. I hope this helpful video helps you out. The next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to service a little safety side marker light for the front fender. These are sealed units so if one of them is out, you need to replace it with a whole entire unit. It's pretty easy. You'll need a Philips screwdriver, a flat blade screwdriver. There are three clips. You can see two black clips lower down. There's three clips and one screw you'll have to remove in order to access the back of the rear of your front fender. Pull the inner fender out, reach behind, release that clip and then pull your inner fender the rest of the way out.
Now, looking up inside, you can see the back of the light and the tab you have to squeeze. Squeeze the tab and pop the light out and you can see here, there's the tab you squeeze, pop it out and then on the connector, there's a little tab, squeeze and disconnect. Install the new one, just reverse. Plug it back in, put the slot in first and snap it in and then put the inner fender back in place with the clip on and re-secure the clips. You pull the center out of the little clips, pull the center out a little bit, push the clip in and then push the center in the lock and then put the screw back into that middle clip. We hope this helps you out.
Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the internet and in person.
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Mazda is a registered trademark of Mazda Motor Corporation. 1A Auto is not affiliated with or sponsored by Mazda or Mazda Motor Corporation.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.