Genuine original equipment part (OEM) that was factory installed on your vehicle by the manufacturer.
Item Condition:New
1 Year Warranty
This item is backed by our 1-year warranty. In the event this item should fail during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Power Window Switch 2005-10 Volkswagen Jetta
Created on:
Tools used
Flat Blade Screwdriver
T20 Driver
T30 Driver
1. Removing the Door Panel
Pry up the pull handle panel with a flat blade screwdriver
Remove the two T30 Torx screws in the door pull
Remove the three T20 Torx screws on the bottom of the panel
Remove the T20 Torx screw at the front top corner of the door panel
Pry out the door panel
Lift the door panel up and off
Disconnect the latch cable from the door handle
Disconnect the window switch wiring harness
2. Removing the Power Window Switch
Remove the three T20 screws on the back of the pull handle
Disconnect the lock switch harness
Apply pressure to the switch and release the tabs on either side
Remove the switch
3. Installing the New Power Window Switch
Insert the switch into the handle
Connect the switch wiring harness
Insert the three T20 screws on the back of the pull handle
4. Reinstalling the Interior Door Panel
Connect the speaker wiring lead
Connect the door lock wiring harness
Connect the latch cables to the door handle
Lift the door panel into place
Push in the door panel clips
Insert the T20 screw at the top front corner of the door panel
Insert the three T20 screws at the bottom of the door panel
Insert the two T30 Torx screws in the door pull
Push on the pull handle panel
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the passenger side power window switch. It's the same part and similar process for the rear door window switches. It's the same part on these Jetta's from 2005 to 2010. The items that you'll need for this is a new power window switch from 1AAuto.com, a T30 Torx bit and ratchet, a flat blade screwdriver, and a T20 Torx driver.
Pry out on your pull handle panel here. Then remove these two T30 screws. We'll fast forward as Mike does that. Now remove this T20 screw and these 3 T20 screws down at the bottom of the door panel. Now pull out on the door panel to release the clips. You just need to pull out all the way along the outside edge. Once you've released all the clips, pull the door panel up and out of the window sill. Then pull it forward. Pull back on this cable to release the clip, and then unhook it from the door handle. Then push the two tabs on your speaker harness and disconnect it. Then, down here, you want to push on this tab while lifting up that purple lever. That will release that harness. Now remove these two T20 screws on the back of your pull handle. Now remove this T20 screw right here. Your pull handle will pull free. You may have to work at it a little bit. Once it releases, just push the tab on this harness and disconnect it.
Now apply pressure to the switch, and then just release the tabs on either side. There are two on each side. The switch will pull free.
On the right is the old power window switch; on the left is the new one from 1A Auto. You can see they're identical and will fit exactly the same.
You can see we've put our pull handle back on and replaced those three T20 screws. Now just reconnect the harness to the power window switch and push it into place. Test it out and it works.
We'll reconnect the harness. Push that purple lever back up. Then reconnect the speaker harness. Then rehook the door handle cable into the door handle and then clip it back in. Then put your door panel back up into the window sill and push it down in. Now make sure your clips are lined up, and put them back into place. Then we'll fast-forward as Mike replaces those four T20 screws and the two T30 screws. Put the pull handle panel back into place. Make sure it's pushed in all the way and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.