WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Tailgate Handle Bezel Set 2001-04 Nissan Frontier
Created on:
Tools used
Flat Blade Screwdriver
Phillips Head Screwdriver
10mm Socket
Ratchet
1. Removing the Tailgate Handle
Lower the tailgate
Remove the two Phillips head screws from the bed liner
Pry the plastic rivets out of the tailgate
Pull off the bed liner
Pull off the tailgate handle plate
Unclip the latch rods from the tailgate handle
Remove the two 10mm nuts from the tailgate handle
Raise the tailgate
Pull off the tailgate handle
2. Installing the Tailgate Handle
Push on the tailgate handle
Lower the tailgate
Fasten the two 10mm nuts onto the tailgate handle
Clip the latch rods onto the tailgate handle
Test that the handle works
Put on the tailgate handle plate
Put on the bed liner
Insert the two Phillips screws into the bed liner
Push the plastic rivets into the tailgate
Remove the emblem from the old handle
Apply adhesive to the handle bezel
Push on the emblem
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a tailgate handle on this 2003 Nissan Frontier, pretty much the same for any 2001 to 2004. You'll need a new handle and trim assembly from www.1AAuto.com, a Phillips screwdriver, a flat blade screwdriver, 10 millimeter socket and ratchet, as well as some glue to refit your emblem.
Locate the two Phillips head screws in the bed liner there. Remove those. I'll fast-forward as I do that. On either side of the bed liner, near the hinges are two plastic rivets. We're going to go ahead and use a flat-blade screwdriver, and pry them out and remove them. Unfortunately, if your tailgate handle is broken, and your tailgate is stuck closed you will just have to break the protector by pulling it off. Now you can remove the bed liner that goes on the tailgate, as well as the small plate that goes underneath it. Now inside, you can see is the back of the tailgate handle, two 10 millimeter nuts hold it on. The rods are held on by yellow clips. Just use a screwdriver to help you push the clips off. Then pull the rods out. If your tailgate is stuck closed at this point, you can then pull on those rods and open up your tailgate. If you pull both rods toward the center at the same time, you should be able to get your tailgate open.
Now, you see one, two 10-millimeter nuts. Go ahead and remove those. Get a good grip. Get your hands underneath there and pull out the tailgate handle assembly.
At 1A Auto, we do offer the tailgate handle two different ways. We offer it just the handle, and we offer it with the whole complete bezel. That's basically because most likely, you're going to break two or three of the tabs off. We actually only broke one off when we pulled it off, but you have to pull quite hard when you pull that bezel off. Usually, you end up breaking a few of the tabs, and it doesn't go back on very well.
Line up the tabs on your trim piece with the handle there, and push it into the tailgate and secure it. With the tailgate down, go ahead and reinstall the two 10 millimeter nuts. I will fast-forward. Now grab the lock rods. Put them back into the holes in the clips. Then snap the clips down on to hold them in place. Go ahead and test it to make sure everything works correctly before you put the bed liner back in.
Put the plate back on, and slide your tailgate bed liner cover over it. Reinstall the two Phillips head screws. I'll fast forward as I do that. Put your two plastic push pins on either side. The emblem is held on by double-sided tape, so we've peeled ours off of the old one and we're using a little bit of adhesive here to reinstall it onto the new bezel. It only goes on one way.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
DHA64764
In Stock
Product Reviews
Loading reviews
4.84/ 5.019
19 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
16
3
0
0
0
Great tailgate handle
tim
January 22, 2017
The handle looked and works just like the factory original!!
R
June 21, 2017
Product came just as promised was easy to install and was a perfect fit.
tailgate handle
A
August 1, 2017
A "friend" borrowed my truck and returned it with a broke tailgate handle... I priced repairing it with the dealer... not so cheap! I've been manually opening the tailgate by pulling the rods through the access opening.
After finding your website and watching the installation video, I ordered the part. Installation took about 15 minutes. Works perfect; Identical to original part; and I saved $100+ without going to the dealer and waiting hours to have them do the repair!
Tailgate latch
H
December 19, 2017
I was surprised and pleased to see that you carried the tailgate latch I was needing. Your shipment was prompt and received it in a few days. You Tube was very helpful with installation instructions and item was easy to install. Very pleased with result. Will recommend you. Mike H.
$100 dollars less than dealer
Gerald
December 26, 2017
2001 Frontier tailgate handle fit well and works perfect. The lever only repair would not have worked, the push in mounting pins broke on removal, so the entire replacement was the only option. NOTE: The original handle assembly had the "NISSAN" logo printed into the plastic and the new on has a spot for a small chrome logo that is not included, ordered on off E-Bay for $10.00 so still a lot less spent.
Was just what I needed
S
June 4, 2018
Service was promp. Online video helped in installing the part.
Perfect fit tailgate handle
Steven
June 15, 2018
I opted to get the complete tailgate handle assembly because of 2 reasons. 1) I didn't want to fuss with installing just the handle. 2) when removing the original, three tabs broke off so I would have needed a new plastic housing anyway. Perfect fit, installed in minutes (after getting the bed liner off). Thanks again 1A Auto for the awesome videos for us DIYers. Not my first purchase from you guys and certainly won't be my last. :) Oh, and did I mention the price?!? MUCH cheaper than other sites for the same product. Shipping was fast (just a few days) too!
Great product
C
August 7, 2018
Very simple to install and looks great. You can find youtube videos to install it in less that 10 minutes. Great purchase
Nissan frontier tailgate handle and bezel set
K
November 12, 2018
My part arrived on time and customer service was outstanding Write your review here. It must be at least 50 characters long. Consider whether you would recommend this product and what you like or dislike about it.
It was fairly easy to install
J
February 14, 2019
The handle & bezel set were great, but did not include new hardware (bolts), so I had to use the existing hardware. This would have been ok except that someone had worked on this handle prior to me and had apparently lost some hardware along the way. Their jury-rigged solution was pretty ugly, and I had to come up with my own hardware to fix it right. Of course this made the whole project harder than it should have been...but the end result works great. By the way, I used 1A Auto's Youtube video to walk me through it; it was a terrific help!
Tailgate Handle and Bezel Set
John
April 12, 2019
Item arrived on time as promised and fit perfect, only reason for 4 stars is the Bezel Set had a blemish on the face, small bubble I guess in the mold.
It arrived; when and what I wanted.
Kenneth
August 11, 2021
process was easy, product arrived when promised, and product was what I requested.
Highly recommend!
Margarita
February 20, 2023
Extremely satisfied costumer.
Perfect Fit at a great price.
Paul
April 25, 2023
This fit my 2004 Frontier perfectly and it was easy to install. Plus the price was very reasonable.
Shipping was fast. Thanks 1AA.
Hard to find part was available with this company
Celeste
June 5, 2023
Who is very happy to find this part as I cook that locally and delivery was fine. Received by scheduled date. Very happy with this company. I can provide be a hard to find part.
Tailgate set
James
February 18, 2024
This product was the perfect replacement!
Daris
May 11, 2024
Fit and operates perfectly
Nissan tailgate handle repair
JOSE
May 22, 2024
Quick shipping very very easy and well explained instructional video, even my husband was able to complete the repair..lol
Jesse
August 31, 2024
Worked amd fits well
Customer Q&A
The "inside/backside" picture doesn't show if there is a white plastic peg that makes locking mechanism work, is it included?February 25, 2020
John G
10
Yes
February 25, 2020
A N
10
Thank you for the inquiry. This will include all necessary parts in order to have this replace your previous tailgate handle and bezel. This will not require any additional parts and is ready to install.
February 25, 2020
Curtis L
10
If it has a key to lock the tailgate it should be included. I bought mine without a lock for my tailgate.
February 26, 2020
Ricardo S
My trucks tailgate doesnt have a lock. Can I change it out with this so it will lock?February 10, 2021
Janell S
10
You would need to buy a lock cylinder in order for the part to work. This will come as only the handle and bezel as pictured.
February 10, 2021
Emma F
Can I use the original lock and put it into the new part? it seems to have come out where it was pressed in.July 18, 2021
John D
10
Yes, this does have the provision so that you can reuse your original lock.
July 19, 2021
Cristina P
10
Yes; I did and it works fine.
August 11, 2021
Kenneth J
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Nissan is a registered trademark of Nissan Motor Co., Ltd. 1A Auto is not affiliated with or sponsored by Nissan or Nissan Motor Co., Ltd.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.