Replaces
Frequently bought together
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet. Hi, I'm Mike Green. I'm one of the owners of 1AAuto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20+ years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly. That's going to save you time and money. Thank you and enjoy the video.
In this video, we're going to show you how to replace the driver's front window motor on this 1997 Cadillac De Ville, same as any '94-'99. Taking the door panel is a little different. This will cover '97 to '99 as far as that door panel goes. The tools you'll need are a flat blade screwdriver, Phillips screwdriver, and a 10 millimeter socket and ratchet. Start by carefully disconnecting the negative battery cable and this should, on most vehicles, will be a 8 millimeter wrench. First, take a flat blade screwdriver, insert in the middle and there's a little tab. When you push on it this comes up, forward and out. And then this back one, there's a little tab here. Just work your screwdriver in there lightly. Pull that out. And this one here, push on the tab. Pry up and off. Same thing here. Push on that tab. Pry up and out. Same thing here. Little tab. Pry it out. Then pull that connector out. Okay now here on this courtesy light, carefully pry the front of it out. There, it comes out. There's a little tab right here. Pull up on it like that.
Now you want to remove this panel here. You basically want to go in and find... you can pull it easy to make sure that the metal tabs don't get caught in your door panel in the leather and rip the leather. You can see this one's caught. Going to use the screwdriver, pry the leather right up over and out. Two connectors. Push a little tab. Disconnect that. And then on this little tab and underneath here, push it down. Disconnect that. Now there are two screws, Phillips. One right there and one right in here. When you got for this one you want to have your screwdriver slightly angled. It's not straight in; it is at somewhat of an angle.
I'm just going to fast forward as I'm just removing those two Phillips screws. Once you remove those screws, lift your panel up and off and reach in behind and disconnect the speaker. Now you want to carefully pull down your water shield. Notice I carefully pull the back to front. I really only need to pull the front part back and expose the window motor. Here's your car window motor. It's held in by three 10 millimeter nuts and there's a lead. Just press the tab back here, pull the lead out. We'll fast forward here as I just remove those three 10 millimeter nuts that hold the power window motor. Then you need a screwdriver and pry the motor right off. There's nothing wrong with our original motor and I'm not one to waste a good part. Re-installation is very straightforward. Just push the motor on. Insert the three nuts.
Just a quick note here. When I put this motor on, the motor pushed all the way nice and flush to the door panel. If your motor goes on but still has a quarter of an inch before it will go against the door panel, that means that the gear is not meshing. All's you want to do is put the three 10 millimeter nuts on, tighten them down very lightly, then reconnect your battery, reconnect your motor and your switch and just run the motor and push that motor in until it meshes with the gears for the window. And then go ahead and tighten it up. We'll just fast forward here as we put on those three 10 nuts and then tighten them up. You want to tighten them up nice and firm. They don't have to be extremely tight, though. You can test it. Plug that in. Make sure you plug in your ... now you can plug in your switch before you put the door panel back together to test it. Now connect the battery. Okay, so the window seems to work correctly so we can take that switch back apart and then put our water shield back up into place.
To reinstall the panel, what you want to do is get your bottom three hooks in first. You just kind of place them close to where they go. Reconnect our tweeter. Make sure all our harnesses come in through here. Okay, our courtesy light back here. Then as we rotate up these two harnesses. Lift up on the panel. Push it in. Make sure it goes on in front and rear. Then push down. Make sure all our harnesses are out. I'm going to fast forward here again as we install those screws. Plug in our courtesy light. Back in place first. Hook these connectors in. Put this in. Hook the bottom in first. Just remember to reconnect your battery and you're all set.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free 888-844-3393. We're the company that is here for you on the internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly: that's going to save you time and money. Thank you and enjoy the video.
In this video, we're going to show you how to remove and replace the rear power window motor on this 1997 Cadillac Deville. It's the same as any 1997 to 1999, similar for the 1994 to 1996. Except the door panel removal, it's a little different. The tools you'll need include a flat blade screwdriver, Phillips screwdriver, and a 10 mm socket and ratchet or wrench.
I recommend you disconnect your battery using an 8mm wrench, not totally necessary, but you will have your doors open for a while so it could run down your battery. First, you're going to carefully pry into the front here. There's a little tab in there that you want to push on. This comes up forward and up. You want to disconnect your cigarette lighter by pulling on these two tabs. There's a tab here, although this looks like it's broken. I'll remove that. Then you want to carefully tie the front of your light, here, back out. Then there's a little tab right here. Pry it with the screwdriver. That disconnects.
This, I'll pull down, up, and out. It should have a third clip. I think I may have forgotten it. Then, there's our lock switch here. Now, there are two Phillips screws, one here, and then one right in here. I'll fast-forward as I just remove those two Phillips screws. Then, up on the panel, and pull it out. Behind here is a little tab on your speaker. Disconnect the speaker. Pull the panel up and off. Pull down. There's your power window right here. There's a lead here. You can pry on it with a screwdriver. Pull it out.
These are 10mm bolts. There's three of them. We'll just fast-forward as we remove those three mounting bolts the 10 mm. They're actually nuts. The motor comes off. Replacing it, it's just simply bolting it back in.
The best technique for this is to put the motor on there and lightly bolt it on. Actually, put some tension into the bolts. If the motor goes right flush with the door panel, then you're all set. It may hang out about a quarter of an inch, which means it needs to mesh with the gear on the window. If that's the case, just tighten it up lightly. Then reconnect your battery, and run the window motor up and down. It will click, and then it will start moving the window. Then the gear is meshed, and then you can tighten up the bolts the rest of the way.
Now, reconnect your window motor. You can see, I've got the battery reconnected and I'm just testing it. The window moves up and down fine. Now, you can put out seal back up in place. Put our door panel back in place and connect our speaker again. These two go up through here and through there. Make sure this harness comes through here. Rotate the door panel back up. Make sure it's pushed on the door. Slide it down. Okay, we'll speed it up here as we put those Phillips screws in, and then tighten them up.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
