TRQ side mirrors and mirror components are designed to match the function, fixture, and performance of the original version for easy installation. TRQ mirrors are DOT certified, comply with all federal safety standards, and are independently lab tested to ensure our products comply with all government regulations. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Direct Bolt-on Replacement: No modifications or special tools required
Complete Assembly: includes same mirror glass, housing, bracket and technology as the original unit
DOT Certified: Built to the highest quality standards
FMVSS-111 Compliant: Validated to be a dealership alternative
Exact fit - To obtain proper fit and function confirm your vehicle has the exact mirror options listed.
Paint To Match Note:
"Paint-to-match finish" refers to a smooth, paintable surface. This item is not painted. Paint offers better coverage and adhesion, but it is not necessary for installation.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
How To Replace Side Rear View Mirror 1995-2005 Chevy Cavalier
How to Replace Mirror 1995-2005 Pontiac Sunfire
Created on:
Tools used
Socket Extensions
Phillips Head Screwdriver
10mm Wrench
10mm Socket
Ratchet
1. Removing the Side Mirror
Remove the Phillips screw from the triangle panel at the top of the door panel.
Remove the triangle panel.
Remove the insulation.
Remove the three 10mm nuts that secure the mirror. Use a wrench for the lower nut.
Pull the mirror free from the door.
2. Replacing the Mirror
Line up the mirror and push it into place.
Replace the three 10mm nuts. Use your fingers to start the lower one (careful not to drop it down into the door).
Replace the insulation.
Replace the triangle panel.
Reinsert the Phillips screw into the triangle panel.
Brought to you by 1AAuto.com, your source for quality auto replacement parts and the best service on the internet.
Hi, I'm Mike from 1A Auto. I hope this how to video helps you out. Next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a mirror on this 2003 Cavalier, pretty much the same as any '97 to '05 Cavalier. This vehicle does have the manual mirrors so this procedure is only for manual mirrors. Tools you'll need are Philips screwdriver, a 10mm wrench as well as a 10mm socket with a ratchet and extension.
Okay. Philips screwdriver, there's a screw right here. Remove it. Okay. Then this kind of lifts up. It comes off. There's some insulation back in here. Pull that out. Okay, then you have three 10mm nuts to hold this on. Okay, I'm just going to use a 10mm wrench. A little difficult to get this one, get it first. Use a 10mm wrench, get it in there and just loosen up that nut. Just takes a little bit of time. Then when you get it loose, just carefully pull it out of there. You don't want to drop it down further into the door.
Okay these two are easy to get out with a 10mm socket with an extension and ratchet. Okay. Pull and push on the mirror. Bases usually get stuck on the door. Your mirror comes right off. As you can see, my original mirror is in good shape. I am going to remount it. Mirror is from 1A Auto. They come just like the original. They're going to bolt right into place. Just need to put it in. Get it in place and make sure the studs get through. I'm just going to take my nut, put it into the socket then put it on. Do the same thing for this one down here. Okay, then lastly this one here. Carefully, I'm kind of using two fingers to get it into place and get it started. Push in on the mirror. I'll get it as tight as I can with my finger. Tighten these two here that were easy to get to. Nice and firm but not over tight. Turns in here again. Tighten it up some with the finger. Then use the wrench. Just need to get in here.
Okay, once that's tightened up put our insulation right back in. Take our trim, put it back on. Screw through, kind of peek through the back and see if the screw is going into the hole. Tighten that up. We're all set.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality auto replacement parts and the bets service on the internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the internet and in person.
Tools used
Phillips Head Screwdriver
10mm Socket
Ratchet
1. Removing the Side Mirror
Remove the Phillips screw in the triangular panel at the top of the door panel.
Remove the foam insulation.
Remove the three 10mm nuts.
Pull the mirror out and off.
2. Replacing the Side Mirror
Line up the mirror and push it into place.
Replace the three 10mm nuts.
Replace the foam insulation.
Replace the triangular panel and the Phillips screw.
Brought to you by 1AAuto.com your source for quality replacement parts and the best service on the internet.
Hi, I'm Mike Green, I'm one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20 plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly, that's going to save you time and money. Thank you and enjoy the video.
In this video we'll be showing you how to replace a manual mirror on this 1997 Pontiac Sunfire same as pretty much a '95 to '05 Sunfire or Cavalier with the manual mirrors and all the only tools you'll need are a Phillip's screwdriver and a 10mm wrench or socket and ratchet.
If you have one of these Cavaliers or Sunfire's with a manual mirror usually if they have manual windows the manual mirror we'll place that here if you give it a little run-ins, it's really a pretty easy task. Just a little Phillip's screwdriver right here for a Phillip's screw. Remove that, the plate comes off and then you can pull this little piece of foam rubber out and there's three 10mm bolts. You see right there, one, two and three. I think you have to be really careful of this, make sure you don't drop these bolts, and for these back two others, 10mm socket and ratchet will be your best bet.
There's the mirror off. Here's the original mirror, here's the mirror from 1A Auto. You can see everything's all the same. 1A Auto mirror comes with a gasket and everything and we'll go on there and fix your broken mirror. Now, obviously this one's fine so we're going to reinstall it and that's really just a reversal of procedure.
Push the mirror on. Get all three bolts on first and then when you tighten these up you want them firm but you don't want to tighten them too much because it is a plastic mirror and you don't want to break studs right out of the plastic. You put your foam on, the tab on the plastic piece that goes behind and then start your Phillip screw and then tighten it up. Then you're all set.
We hope this helps you out. Brought to you by www.1AAuto.com . Your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free 888-844-3393. We're the company that's here for you on the internet and in person.
MRA05296
In Stock
Product Reviews
Loading reviews
There are no reviews for this item.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.