1992 Chevrolet Suburban C2500 with Delay Wipers Windshield Wiper Motor TRQ WWA10628

Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all backed by our 100% satisfaction guarantee. Visit us at 1AAuto.com, your trusted source for quality auto parts.

In this video, we're going to be working with our 1996 GMC Sierra K1500. We're going to show you how to remove and replace your vehicles windshield wiper motor right here. If you like this video please click subscribe. We have a ton more information on this truck as well as many other makes and models. If you need this part for your vehicle, you can follow the link down on the description over to 1AAuto.com. Here are the items you'll need for this repair.

Use some small pieces of painters tape to make a straight line with your wiper blade. This will help us position the arms back on without needing to do trial and error. Using the flat blade screwdriver, pry out on the tab on the top edge of the wiper arm at the pivot. Remove the wiper arm from the pivot. Do the same thing on the opposite side.

Remove the weather strip from the top of the firewall. Remove the three Phillips-head screws securing the cowl to the truck on both sides. There's one down on this opening. There are three, both in the same positions on either side of the vehicle. Once you get the first three screws removed, lift up and remove this corner panel that goes around the hinge. There's a fourth Phillips-head screw under there you'll also need to remove. Remove the three screws from each corner of your cowl.

Once that's done, you can remove all four of the Phillips-head screws along the front of the cowl. Pull back and lift up to remove the cowl. You'll need to disconnect the washer hose over here on the driver's side. Remove the cowl from the vehicle.

Loosen the 10 millimeter nuts on the wiper linkage. There's no need to remove these entirely. If you're doing the driver’s side arm, you can stop here and move on to removing the other portion on the other end of the arm. However, for the passenger side, you'll need to loosen this.

Remove the blue safety tab in the connector by pulling it straight back. Lift up on the tab with a small flat blade screwdriver and remove the electrical connector. Then remove the three 10 millimeter bolts around the body of the motor with a 10 millimeter socket ratchet and extension. Once the screws are out, wiggle the motor to release it and then you want to pull back at the driver side, slide it out until the center of the pivot ball is in the center of the opening, and then pull out to release it.

Reinstall the wiper motor by sliding the arm back through in the opposite fashion you used to remove it. Start one of your 10 millimeter bolts to keep it in place. Get the other two going, reinstall them with your 10 millimeter socket ratchet and extension. Reinstall the electrical connector and snap the blue safety tab back into its loop. Snap the arms back on to the wiper, tighten them back down with your 10 millimeter socket and ratchet. Make sure they're in the same place they were removed from.

Reconnect your windshield washer hose, and lay the cowl back into place. Reinstall the four screws in the center section of the cowl. Reinstall the two short screws on the end. Once the rear one's in, you can reinstall the plastic cover. It simply slides in and drops down. Reinstall the longer screw on the outer edge here. Repeat these steps on the opposite side. Reinstall the weather strip onto the top edge of the cowl.

Now, I know we had mentioned using the painters tape to align these earlier, but it turns out these wipers are keyed, which means they'll only go on one way. Simply pull out the tab and slide them back on. Lock the tab back into place. Lay the wiper down. Remove the tape.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet.

Hi I'm Mike Green, I'm one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my twenty plus years' experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly, that's going to save you time and money. Thank you and enjoy the video. In this video we will be showing the steps to replace a wiper motor in this '99 Suburban, same as most '88 to '98 Chevy trucks and '92 to '98 SUVs. Tools you'll need are pretty simple: flat blade screwdriver, Phillips screwdriver, and 10 and 11 millimeter socket and ratchet set.

To remove the windshield wiper arm, pretty easy. You flip the arm up and there's a little tab right here and that pulls up. Then you can just work your hand underneath there and pull it up and off, same thing for the other side. After you remove the wiper arms, you're going to remove six Phillips screws. One there, one in that round hole there, you probably can't see, but it's in there, one there, one there and then finally one right there. I'll remove those six. Okay for all these corner ones when you pull it up there's this little grille here just pull that back, up, and off, screw comes out with it. After you pull those covers back on the side there's two more screws underneath on the edges. There are two more screws right here along the edge, turn them. Both those screws are out, pull them up over the wiper and don't forget to disconnect your windshield washer hose right here.

Now I'm going to put my penetrating oil down there for a little bit, loosen it up. The driver side linkage will comes off. Passenger side linkage comes off. Once you have those wiper transmissions unhooked, your wiper motors right here under the hood, three 10 millimeter bolts, your harness is hooked right here to the little lock, you pull out with your thumb and the harness you pull up on this with your hand and unplug the harness. Then you have the three bolts to take off. Once those bolts are out, give it a hard, it just sticks on here a little bit. The whole thing pulls out like that. Here's my original motor, here's my new motor from 1A Auto.

The motors are all the same. You may run into this, the new motor comes with a single ball, on this vehicle, on this truck that I'm working on it has this double ball so if I was replacing this motors' actually fine so I'm going to put it back on the truck I'm just using it as an example, but if I was replacing it you just remove this 13 millimeter nut and you basically tap the arm a little bit, it will loosen and pull it off. Try to put the new arm in the same position. If you want you can actually turn these so you can point the arm right at save this grommet, make sure you put them all in the same position. I'll show you how to line it up when we put it back in the truck. The top of the arm, its 13 millimeter, pull it off there. You might need to put this in a vice to get the bolt out, but it's not that big of a deal.

Now I'll put the original one back in the truck I'm going to clean up this ball here a little bit first. Putting the motor back in, pretty obvious, put the arm in, hold it in there, put in your three bolts. I'm going to save you watching me tighten these bolts up, just fast forward through it here, obviously you need to reconnect your harness and lock it back in place. If I take this and I pull it up a little bit you want your arm facing that way once you've put it back together. You want this one to go right on that inside ball on this truck. We'll just tighten up a little bit; actually we'll align them first. You want to pop it on right there, tighten it up a little bit and it's okay if they're sliding a little bit.

Got my wiper arms back on and I can take them back off and put the grille on, but you can see without those transmissions tightened you can move your arms back and forth a little bit. You can just get them where you want them as long as they're in parked position and then you can tighten them up. Then after you have them tightened up. Let them run a couple times to see if they go down back where you want them. I'm actually going to adjust this one down a little bit more. Once you have your wiper arms where you want them you want to tighten up the transmissions. I'm fast forwarding through putting the grille back on just because the YouTube 10 minutes, but you want to put the two screws in that you can reach under the hood, put those on then lower the hood.

Put your corner screws that are underneath on first then put the corner bezels or trim back on and tighten up all the rest of the screw and you should be good to go with some nice quiet, new wipers that are working correctly. Obviously once the grilles back on then you want to put the wipers back on as well.

We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet, please feel free to call us toll free at 888-844-3393. We're the company that's here for you on the internet and in person.