with RPO Code UK3 (Electronic Accessory Control System)
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Intermediate Steering Shaft 1999-2006 Chevy Silverado
Created on:
Tools used
Bearing Grease
15mm Wrench
Torque Wrench
15mm Socket
Ratchet
Needle nose pliers
Assistant
1. Removing the Upper Steering Shaft
Remove the 15mm bolt that connects the upper steering shaft to the lower steering shaft
Remove the 15mm bolt from the top of the steering shaft
Pull the steering shaft loose at each end
Pull the steering shaft out from inside the cabin
2. Installing the New Upper Steering Shaft
Check that the new upper steering shaft fits into the lower steering shaft
Feed the steering shaft into place from inside the cabin
Apply grease to the bottom of the upper steering shaft
Push the upper steering shaft into the lower steering shaft, using needle nose pliers
Insert the 15mm bolt that connects the upper and lower steering shafts
Tighten the 15mm bolt to 37 foot-pounds of torque
Pull the upper steering shaft into place inside the cabin
Push the 15mm bolt into the top of the steering shaft
Put the key into the ignition
Turn the steering wheel so that the bolt end is facing down
Fasten the 15mm nut onto the 15mm bolt
Tighten the 15mm nut to 35 foot-pounds
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and, please, next time you need parts for your vehicle, think of 1AAuto.com.
In this video, we're going to show you how to replace the upper steering shaft on this 2002 Chevy Suburban and it's the same part and similar process on these Suburbans from 2000 to 2006. The items you'll need for this are a new upper steering shaft from 1AAuto.com, 15 millimeter socket and ratchet, 15 millimeter wrench, torque wrench and grease.
Start off by removing this 15 millimeter bolt right here on the steering shaft. You can see, Mike uses a wrench to break it free, but then, what you want to do is put the wrench on one side and the socket and ratchet on the other and just remove that bolt the rest of the way. Now just above the gas pedal and brake pedal, you'll see the other end of the steering shaft and you want to just remove this 15 millimeter bolt right here. Now, we'll fast forward as Mike does this and you can see he's just using the wrench on this part. That's really the easiest way to do this. Now pull the bolt free. Then, pull the steering shaft free, and then pull this end free. Then, go back inside the vehicle and then just pull it out from that end. It should pull right out.
On the bottom, is the old steering shaft. Above it is the new one from 1AAuto. You can see they're identical and they'll fit exactly the same. You need to make sure that the new steering shaft will fit in to the lower shaft and sometimes, due to over tightening, the lower shaft could be pinched in a little bit. So, we just fit it in there from the top without putting it into the vehicle to make sure that it'll go through. Now, feed the steering shaft in from the inside of the vehicle. You do have to maneuver it around to get it to go through the boot. Then apply grease to this end of the steering shaft and then, push the upper steering shaft back into the lower steering shaft. To make the process a little easier, you can use needle nose pliers. You can just kind of pry the hole down while someone pushes from the inside and you don't have to have someone pushing from the inside but it does kind of speed up the process a bit. Using needle nose pliers, just keep the hole for the bolt lined up and then just push the bolt into place. Then we'll fast forward as Mike tightens that up. Then just torque this bolt to 37 foot-pounds and then pull up on the upper steering shaft and push it up into place. Then just push the bolt back into place and then put your key in the ignition and just turn your steering wheel so that the bottom of the bolt is facing down so it just makes it easier to get the nut on there and in place. Then just tighten that up, and just torque it to 35 foot-pounds, and then you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
905-512
In Stock
Product Reviews
Loading reviews
5.00/ 5.01
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
steering column bearing
E
January 26, 2020
I got the bearing in five days after ordering. We installed it and it works well now. Installation was a little hard but that is to be expected with this operation. The video is very helpful.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Chevrolet is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by Chevrolet or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.