2008 Pontiac G6 L4 2.4L Dual Radiator & Condenser Fan Assembly TRQ RFA83392

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the radiator fan in this 2007 Pontiac G6, pretty much the same for a 2005 to 2010 G6, as well as the Saturn Aura. A radiator fan should come on when the AC is on or when your engine gets to a certain temperature, usually 210 degrees Fahrenheit. If the radiator fan isn't coming on, check the relay, check the fuses and if that's not working then, most likely, your fan needs to be replaced. For this repair, you're going to need a new radiator fan from 1AAuto.com, 7 to 10mm sockets with ratchet, Phillips and flat blade screwdrivers, pliers, flashlight and a drain pan.

Start out by removing the cover that's on the battery and then disconnect the negative battery cable. It's the black cable, or the cable that's closer to the front.

Remove the oil fill and lift the engine cover up and off and replace the oil cap.

You're going to start out by removing a series of clips at the top of your bumper cover right over the grille. For these clips, as you can see, work your screwdriver underneath. Pop up the middle of the clip and then the rest of it will pull out and it may stay behind, so you may use the screwdriver and pry out the second part of the clip.

Now, remove the two 7mm bolts that hold the two tabs at the top of the headlight. Pull on the outside of your headlight, there's a ball and socket on the outer corner that will stick in there. Then, kind of force your headlight into the inside of your bumper cover. Pull it up and out, and then disconnect it.

Now, there are few 10mm bolts at the top of your radiator support closeout panel, remove those. Then, you can pull out slightly on that panel and there are three 10mm bolts that hold your hood latch assembly in place. You want to remove those. You don't have to do this. You can get that closeout panel off there without doing this, but, if you take off the latch, it just makes it that much easier. Then, move that latch and pull that closeout panel right out, and just move your hood latch out to the side and away. Now, you need to remove the engine air duct by removing the pin there, and then you can reach under and pull that duct forward and out.

Two bolts hold the upper radiator mounts in, those are 10mm and I'll fast forward here as we'll just remove those and take the mounts out and put them aside as well. There are two clamps that hold the intake hose on, and the first one is over there. Tthis one, a little hard to see, but the screwdriver's right down on it there. I'll fast forward as we loosen up the two clamps and then take a pair of pliers and there's a squeeze clamp on the top. You can remove the intake duct.

Position a drain pan underneath, and then, with a pair of pliers, you can have easy access to this radiator hose clamp. Squeeze the clamp and then move it back off of the radiator inlet and onto the hose. Now, reach in. What we want to do is to kind of try and twist the hose on to break it free from the plastic radiator inlet and then as you start pulling it out, some of the fluid will come out and you can allow some of it to drain and then pull the hose up and out. If you just walk it up there, it won't leak anymore.

Now, there's a series of electrical connections. To undo the safety clip there, unplug that. Then for the harness that's in the alternator, unclip that, and the further out of the way you move all these harnesses, the better off you'll be. A lot of times, they just get caught up on the radiator fan as you try to lift it up and out. Then, up top, there are the airbag sensors. They have little safety clips that pull out and then disconnect them. You also want to remove the clips from the radiator support and then just move that harness out of the way. There are two ground nuts. Just remove the nuts and remove the ground straps off the radiator support there. For the transmission line that runs down the driver side, pop it out of the clip.

Disconnect the fan on the left side. There's a little tab that you push up and pull out and then there's also a clip that you want to undo. It's the same thing on the other side; there's a tab you pull up. You pull it out and move those to the side. Now, what we're doing here is . the radiator is down in a couple of cushions. What you want to do is pull it up out of the cushions first and kind of remove the radiator towards the front of the vehicle. That just gives you a little extra clearance. Then, you hold the radiator down and pull the radiator fan up and it unlocks from some clips that are in the radiator. Then, you have to . there's tabs on the radiator fan that you've to get by the hoses. So, you kind of have to move it over to the driver side of the car first, actually, over to the passenger side first, to get the tabs up and around. Then move it back towards the other way and pull the tabs up around and then start pulling it out. Now, tilt the radiator fan forward. It's just a matter of getting it pass the clips. Making sure none of the wiring harnesses get stuck on it. The better you tuck them out of the way, obviously, the better off you'd be. There's limited clearance between the radiator support and the AC, but you pull it up through there. Again, if you're encountering a little too much force, just look down in there. You can see we found a harness that was catching on it. Pull that harness out of the way and it'll come up and out.

Before putting the new fan in, just make sure you tuck any wires down and out of the way. Angle the bottom of the fan down in towards to the radiator and then just, gain, make sure it's not getting caught up on anything. Slide it down in. It does require a little bit of force and then once you get it kind of underneath the radiator crossmember, remember you need to move it side to side to get the tabs around the hoses. It's somewhat in place. There's two tabs on each side, you can see right there. Make sure you press it towards the radiator. Lock it down to the tabs. Do the same thing: press the fan assembly towards the radiator and lock it down into the tabs.

Put that transmission line back into its clip. Now, you can reconnect. Start by reconnecting the fan. Make sure you put all the clips back in place that hold the wiring harnesses, so they don't caught up on anything. Reconnect the alternator, and the other connections and also make sure you now reconnect those two ground straps and tighten those nuts up. Reconnect all the airbag harnesses and again, make sure that all the clips are back in place.

Make sure that you get the radiator back into its lower support grommets. You should feel it push down into the rubber grommets and you can start installing the passenger side radiator bracket. Here, we kind of preposition the hose clamp and then put the radiator hose back on the radiator. Pinch the clamp with the pliers. Push the hose on and make sure it's nice and secure. Make sure it's all the way on to the inlet too, in the radiator and clamp is nice and secure.

Make sure you take your cable and latch mechanism. Put it in or just get it routed correctly. Then, put the driver side radiator support bracket on and then tighten them both up. Make sure the hood latch cable is properly routed. It should go underneath the air inlet duct. Reinstall that air inlet duct. Put it in the place, and then, there's a pin that holds it to the radiator support bracket.

Put the upper closeout panel in. You have to pull the bumper cover out and while it's still loose, you're going to want to reinstall the bolts that hold the hood latch support in. I'll go really fast through that. Having it loose just allows you more clearance to get those bolts for the hood latch support back in. Before you tighten up the hood latch you can see the little places where the bolts were, so just slide the hood latch into the same spot on the bolts and then tighten it up. This will help you get a good alignment on your hood. If you should close the hood and it looks too low, then, you'll loosen up the hood latch support or the hood latch and just move it up a little bit. If it's too high, loosen it up, and move it down a little bit.

Reinstall the head light. First connect it, and then, you're going to slide the inside in place behind the bumper cover a little bit first and then push the outside and make sure that that tab lines up. Push it outside in and secure it with the bolts.

Reinstall two clips that hold the closeout panel, underneath the bumper cover. We'll keep fast forwarding here as we put the bolts that hold that closeout panel back on, on top and as well, we'll put the clips back in place. The clips, they're usually two piece. Make sure that the center is pulled about a quarter of inch out and then, put the clips down and in and then push the center down to lock them.

Put the intake hose or ducts back in. Make sure you connect it to the air filter box correctly. Connect it to the throttle body correctly. Use some pliers and re-clamp the tube on top, and then make sure you tighten up the clamps nice and firm.

Reinstall the engine cover by removing the oil cap. Put the cover back on, replace the oil cap. Reconnect the negative battery cable and reinstall the battery trim box. Make sure you re-add the coolant. We're using a funnel that has a filter in it. Put the coolant back in it. Run the car for a little while, check that fluid level, and make sure you refill it as necessary.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.