2009 Chevrolet Malibu Front & Rear 6 Piece Suspension Kit TRQ PSA56225

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet. Hi, I'm John from 1A Auto. I hope this how-to video helps you out and the next time you need a car for your vehicle, think of the 1AAuto.com. Thanks.

In this video we're going to show you how to replace front struts on this 2007 Pontiac G6. Very much the same for any 2005-2010 G6 as well as the Saturn Aura. We're going to show you the right hand side. The left hand side is the same procedure and we always recommend that you replace your struts in pairs. And speaking of struts you want to get a nice new set of loaded struts from 1AAuto.com. We sell both brand name as well as private label: Jack and Jack stands, 10, 18, and 19 mm sockets, ratchet and breaker bar or pipe for some extra leverage, and 18 mm wrench and a hammer.

Start out by using just the socket to loosen the lug nut covers or the wheel cover as in this case. We're going to use impact or air tools sometimes. If you don't have the benefit of air tools just start with the vehicle on the ground, loosen the lug nuts then raise and secure the vehicle and remove the lug nuts, wheel, and tire and grab the suspension and turn the wheels or turn them with the steering wheel and there's a 10 mm bolt that holds the brake line bracket to the strut, remove that.

There are 2, 18 mm nuts on the back side of the strut. You want to use a ratchet, using a breaker bar and a pipe or something here for some extra leverage might be in order but you can see on our vehicle they come off with just a good amount of force. Use an 18 mm wrench to grab onto the nuts part of the stud of the stabilizer link and then use an 18 mm socket. Loosen up the nut and then it comes off. Use a hammer, be careful not to damage the bolts too much. You might want to put a nut on the back of them and although ours came out pretty easy, and just drive those bolts right out. Heading up top underneath the hood, there are three 13 mm bolts that hold the top of the strut in place and we'll fast forward as we remove those. You can remove 2 of them and then just loosen one up most of the way.

And as you're taking that last nut off, you can just keep your hand on the strut and as you take the nut off you will be able to lower the strut out. And then put the strut back in place and yes, you probably will notice that we're just putting the old strut back in. The struts in this car were in fine shape and so we're not usually ones to waste putting a new strut into a car that doesn't need them. We're just kind of doing this to show you how to do it but you put it into place, start one of the nuts on top and then start the other two and you can tighten those up and the top nuts you should torque to 20 to 25 foot pounds.

Back down under now, lift your brake hub assembly and steering knuckle back in to the strut. You can force it in there and you put one of the bolts in, and just kind of put it in a little bit and then as you move the knuckle around on the strut you should be able to get the bolt through. Then make sure you put the bracket back into place and you can get the second bolt through and if you like use a hammer or something just to drive the bolts all the way through. And it should be noted that we do recommend an alignment after you do this because the movement of these struts is something that affects the caster and camber of your wheels.

And torque those nuts to 85 foot pounds. Bring the sway bar link back into place and should you possibly feel the need to replace those sway bar links, 1AAuto.com, we sell those as well but then use a 18 mm wrench and an 18 mm socket and ratchet to tighten up that bolt. That bolt should be tightened somewhere around 70 to 75 foot pounds. Put the bracket that holds your brake hose back into place and start the 10 mm bolt on and tighten it up. Please install the wheel and put the lug nuts on by hand first just to make sure you don't cross thread them then tighten them preliminarily.

the vehicle on the ground, torque the lug nuts to 100 foot pounds using a star pattern. Now reinstall your hubcap and I'm going to do that with that 19 mm socket and then I'm just going to screw them in by hand. Also want to make sure that you line up the valve stem with the notch in the hubcap for the valve stem and I'll go ahead and fast forward through that.

We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free: 888-844-3393. We're the company that's here for you on the internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace a front stabilizer link on this 2007 Pontiac G6. It's the same as any 2005 to 2010 G6, as well as the Saturn Aura. Not a difficult procedure. You will need jack and jack stands, and you'll want to jack up both front wheels off the ground and support it with jack stands. Then you'll need a lug wrench or a 19mm socket with a ratchet, maybe even a breaker bar and a pipe for some extra leverage. Then, after that, you'll just need two 18mm wrenches, one of those 18mm will have to have an open end.

Start out by using just a socket to loosen the lug nut covers, or the wheel cover as in this case. We're going to use impact or air tools sometimes. If you don't have the benefit of air tools, just start with the vehicle on the ground, loosen the lug nuts, then raise and secure the vehicle, and move the lug nuts from the wheel and tire.

Use an 18mm wrench to grab on to the nuts, part of the stud of the stabilizer link, and then use an 18mm socket, loosen up the nut, and then it comes off. Here's the fun part of the repair. You pull that down out of the way, and you can see the other end of the link right there. Put the 18mm wrench on the nut that's in the shaft, just like before. Then, there's not really enough room to get a ratchet back in there, so you basically just have to take a wrench and slowly, carefully, one eighth of a turn at a time, and I'll fast-forward the video as we do that.

Then, just reinstall the link as you took it apart. Go ahead and speed up as we tighten up that lower nut, and like I said before: it's not all that difficult; it just takes quite a bit of time because you can't move that nut too far each time.

Bring the sway bar link back into place, and should you possibly feel the need to replace those sway bar links, at 1AAuto.com, we sell those as well. But then use a 18mm wrench and an 18mm socket and ratchet to tighten up that bolt. And that bolt should be tightened somewhere around 70 to 75 foot-pounds. Put the bracket that holds your brake hose back into place, and start the 10mm bolt on and tighten it up.

Reinstall the wheel. Put the lug nuts on by hand first just to make sure you don't cross thread them, then tighten them preliminarily. Put the vehicle on the ground, torque the lug nuts to 100 foot pounds using a star pattern. Now, reinstall your hubcap and we're going to do that with that 19mm socket. I'm just going to screw them in by hand. Also, we want to make sure you line up the valve stem with the notch in the hubcap for the valve stem. I'll go ahead and fast-forward through that.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

In this video, we're going to show you how to replace a front stabilizer link. The symptom of a bad stabilizer link is if you're hearing a clunking in the front of your car, but when you go around a curve, either left or right, the clunking seems to go away. That's usually a sign that your stabilizer link is starting to loosen up. Tools you'll need are 8mm to 19mm wrenches as well as a hammer.

Turn your wheel all the way to one side or the other. Then you can reach in behind and you can see it here. This is the top of your link. You can reach in behind and grab that with your hand and shake it back and forth and if you can duplicate that clanking or rattling sound then that's what you need to replace.

Start out by using a 19mm socket or a wrench and loosen the plastic covers and then remove the wheel cover. If you don't have the benefit of air tools, you'll want to loosen the lug nuts up while it's on the ground, then raise and support your vehicle and then remove the lug nuts and the wheel.

Right here is our stabilizer link. Use a little bit of penetrating oil on the upper and lower, let that sit for awhile. We've got an 18mm wrench on the bolt and 8mm wrench on the end of the shaft there. It looks like it actually coming loose, there goes that bolt. Get that started. Put this on there and I'm going to put this one on down there and same thing. Here's a close up look. I've got the 18mm wrench on there. The 8mm wrench is just holding that stud in place and I just keep flipping back and forth with the larger wrench, grabbing onto the nut and removing it. I'm just going to speed up the tape here. It takes a little while to get these things apart. It's a tedious task of getting the wrenches in there, holding it with the smaller wrench and then using the small one and then just angling the larger wrench in there as best you can. Eventually it comes apart.

Here's a new link from 1A Auto. Iit's a little bit different but it actually makes it easier to install. You'll need a 15mm wrench to hold this on that side and then a 19mm socket and ratchet to put the bolt on. We're going to put down in. It mounts in just like your original. Start the locking bolt on here and we'll start the locking bolt down here. Up top, I put my 15mm wrench through from the backside and then a 19mm socket and ratchet. I'll just speed it up as I tighten it up with the ratchet and you want to get it nice and tight and probably 40 to 45 foot-pounds. Then continuing on down to the lower, it's the same as taking it apart. You really can't get a wrench in there or a ratchet in there so you just have to use a wrench. I used the 15mm wrench to hold the stud and then a 19mm wrench to tighten up the nut and it just takes a little while and, then, again, tighten it up between 40 to 45 foot-pounds.

Once you have the wheel back in place then you put the lug nuts on by hand and I just use my impact wrench to just tighten them preliminarily. Now with the vehicle on the ground, torque the lug nuts to 100 foot-pounds using a star pattern. Now put your wheel cover back on, there's a hole for the valve stem then use a socket to tighten up the retainers.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.