Replaces
Frequently bought together
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the camshaft position sensor on this 2004 Chrysler Sebring. This model has the 2.7 liter V6 and it's going to be the same process on any of the Dodge and Chrysler vehicles with the same engine. The only tools you're going to need for this are a new camshaft position sensor from 1AAuto.com, a 13mm wrench, and a flat-blade screwdriver.
To locate your camshaft position sensor, it's right here with the red clip on it. You're going to have to first remove that plastic cap. So, just using flat-blade screwdriver, pop that cap off and then you just want to push down on that red tab and then the harness should pull right off. Now, you just want to remove this 13 mm bolt. We're just going to fast forward as Don removes this. Once that bolt is removed, the camshaft position sensor will pull right out.
On the right, is the old position sensor; on the left, is a new one from 1AAuto. You can see they're identical and will mount exactly the same. You want to just take your new position sensor and push it down into place. Then, go ahead and replace that 13mm bolt, and we'll fast forward as Don tightens this up. When you tighten it, make it firm with that small wrench which is probably around 12 to 15 foot pounds, not too tight. Now, you can reconnect your harness. Push that red clip back up, and replace that cap. Now, your camshaft position sensor is all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video we're going to show you how to remove and replace a throttle position sensor on this 2004 Chrysler Sebring. It has a 2.7-liter V6, and this procedure should be basically the same for any vehicle, Dodge or Chrysler, with the 2.7-liter V6 and this style throttle position sensor. The only tool you'll need is a T20 Torx driver.
The throttle position sensor is the at the back of the engine near where the intake hose comes in. Press the tab and pull the connector off. Two T20 screws hold the position sensor in place. You can see we have a socket that has a T20 Torx bit in it. We're removing those two screws. Be careful as you handle the screws; make sure you don't drop them down. Once you have the screws out, then pull them up along with the sensor.
Reinstallation of the new one's no mystery. Put it into place. Make sure it goes in properly and start the T20 screws in. Start them in by hand first. Make sure they thread correctly, then tighten them up. You don't need to have them too tight. They need to be nice and firm but don't overtighten them. Once you have those tight, make sure you reconnect the harness.
If you're going to remove your air box, loosen that clamp. There's also usually another bolt down where his forearm is that holds the air box to the frame, but you can see, you remove sensor, the hose, and then pull the air box up and out. Then we'll reinstall our air box and tighten up the clamp that holds the intake hose to the throttle body, reconnect the hose, and reconnect any of the sensors you might have disconnected.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
