Replaces
Frequently bought together
This 4X4 Disengage Solenoid is just what you need to get your four wheel drive system working again! The factory solenoids commonly fail due to cracking and leaking, resulting in failure of the four wheel drive system.
Specifications
Note: There are two solenoids located side by side in the housing; engagement & disengagement. The simple way to know which is which is the key way location: holding the solenoid with the connector at the top and vacuum lines on the bottom, the engagement solenoid key way will be at the 9 o'clock position (to the left), the disengagement solenoid key way will be at the 6 o'clock position (bottom).
If one of the two solenoids fail, the 4 wheel drive system will be inoperative. Both solenoids must be functioning properly for the system to operate.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all backed by our 100% satisfaction guarantee. Visit us at 1AAuto.com, your trusted source for quality auto parts.
On this Ford F-150, your engage solenoid should be on the driver's side, or general location is passenger's side, but this is towards the driver's side. You can make sure it's the engage one by unplugging it and this key way should be in the 9:00 position.
To remove, use a bent tip awl. There's just a little tab back here that you need to push back. Then you push the solenoid down, pull it up and out, and remove the vacuum lines.
Install the new engage solenoid. Make sure that it has the key way at the 9:00 position, put it down and in, and it should slide right up and in, and click in place. Then you can reconnect your vacuum lines, push firm, and then reconnect your electrical lead.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Hi. I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all back by our 100% satisfaction guarantee. So visit us at 1aauto.com, your trusted source for quality auto parts.
Four-wheel drive solenoids are right back here behind the battery. Be careful when you're working around the battery. We do have ours disconnected.
A new one from 1A Auto. The disengage solenoid comes with a bracket. This bracket works for most applications. We're not going to use it for this application, so what we're going to do is just use a 90-degree pick. Put it in here. Pry back on this tab, and then you should be able to slide the solenoid down and out.
This is the disengage side. You can tell them apart by seeing where this tab is. If you disconnect this first solenoid, you'll see that it's here at the nine o'clock position. This one is at the six o'clock position, so you know it's the disengage.
And obviously if your four-wheel drive is engaging but the axle doesn't disengage, that's usually the problem with the solenoid.
To remove it, again, use your 90-degree pick. Go in behind and push on the tab. It's back here--it's the same tab here. Just get your pick in there and push on the tab. Push on the tab and then push the solenoid down, and it comes out, and then you can just pull these vacuum lines off.
New one from 1A Auto is the exact same as the original. You can put it into place. Go down with it and then bring it up until it locks into place, then just reconnect the engage solenoid. Then reconnect your vacuum lines, and reconnect the electrical feed.
Thanks for watching. Visit us at 1aauto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
