Replaces
Frequently bought together
Install Tip: You may be required to reset the vehicle computer after installation of this part.
Direct Fit Replacement - Guaranteed to fit and function for your specific application
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the mass airflow sensor or airflow meter on this 2006 Ford Explorer with the 4.6-liter V8 engine. It's the same process for any 2006 to 2010 with the V8, as well as similar procedure for the V6. The only tools you'll need include a flat blade screwdriver, a T20 Torx driver, and a new airflow meter from 1A Auto.
Start out by opening the hood. Pull the opening lever inside, and then there's a little secondary latch that you lift up on and it kind of pivots out of the way. It helps if you're using two hands, but I'm using one so I can hold the camera. You can see there's the handle, and that pivots out of the way so you can lift your hood up. The air box is right over here. You want to disconnect your airflow meter by pulling back on the red tab and pushing down on the tab in the middle. When that disconnects, you'll want to loosen up the flat blade screw that holds the clamp.
There are three clamps that hold the air box cover. Undo those one's a little tricky to get to, you kind of have to reach under the tube and now you can pull the tube off and the top of the air box comes right up and out. Two T20 screws hold the airflow meter, and you can seem them, they're the silver ones right there. We'll use a T20 Torx driver and remove those screws. Then our airflow meter will come out.
Install your new airflow meter from 1A Auto. We offer both an OE replacement as well as aftermarket options. They'll fit right in place, and then replace those two T20 screws and tighten them up. You want to make sure they're both hand tight first, then get them snug and tighten them up afterwards. The air box has five tabs along the side, so make sure they go in and under the slots in the bottom of the air box, and make sure that your air filter's in place correctly. Once you get it in place, it should go right down. Put that tube in there, and now we're going to re-clamp the three clamps that hold the top of the air box to the bottom.
Just make sure our harness is up and out of the way, we'll actually connect it right now. Push the safety tab in, re-secure that third clamp, and then get that hose in place and tighten up the clamp that holds the hose onto the air box.
Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.
Tools used
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the mass air flow sensor on this 2005 Ford Focus with the 2 liter, 4 cylinder engine. It's the same part and process on these Ford Focuses from 2003 to 2007. The items you'll need for this are a new mass air flow sensor from 1AAuto.com, jack and jack stands, and a T20 Torx driver.
Start off by raising the front of the vehicle. The mass air flow sensor is located right here. Start off by prying up on this red clip and then pushing the tab on the harness and pulling it free. The sensor is held in with two T20 Torx bolts. We'll just fast forward as Don removes both of those. Once those are removed the air flow sensor will pull right out.
In the back, is the old mass air flow sensor. Up front, is the new one from 1A Auto. You can see they're identical, and they'll fit exactly the same. Put your new mass air flow sensor into place and replace those two T20 Torx bolts. Reconnect your harness and push that red tab back in.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
