Replaces
Part Details
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a front window regulator on this 2002 Ford Escape. We will be working on the driver's side, the passenger's side front door is basically the same procedure. This is the same for any 2001 to 2007, also similar for the Mercury Mariner. You'll need a small flat blade screwdriver, a Phillips screwdriver, and a 10mm socket with a ratchet and extension.
To start out, use a little screwdriver, there's a little trapdoor here, reach in, pry it out, and there's a Phillips screw back in there. Same thing here, pop that off, and there's a Phillips screw right down in the door pull. Another Phillips screw is on the back. We'll just fast-forward here as I remove those four screws.
Once you have those out then you can pull your bezel around your door handle here right off. Now, usually you can reach right into this corner and start pulling out and work your fingers underneath. Pull out firm, there's a series of clips that hold the door on. There are two up in here. The door panel comes off. Even though I'm going in fast motion here, you want to carefully pull your water shield down. Be careful not to ripe it. While you're doing that also there's a Phillips screw there on the bracket that holds that bracket in place. Remove that and pull the water shield down so you can access the inside of your door.
The window regulator on these vehicles are cable actuated. Actually, the regulator on my truck is absolutely fine but I wanted to do this video to show you what will happen when your regulator breaks. It is generally when you press the button, but when it breaks you'll hear a clicking or grinding and then a pop noise. That pop is usually the cable breaking. Once your regulator's broken, your window will probably just fall down into the door. Once you get to this point, you can lift, raise, and lower your window by hand. What you want to do is put your window at this point so you can see these two bolts here, and you want to remove, I believe yes, you want to remove those two bolts.
Increase the speed here as I use a 10mm socket with a ratchet and extension to remove those two bolts. Now, you can remove this piece of weatherstrip, and then your window will come up off the regulator. You can pull the back of it up first, and pull the window right out. Now you'll want to disconnect your lead to your window motor by pressing a tab there and pulling it off. Then these three bolts here hold the motor in, and then this nut and this nut down here holds your window regulator on. I'll fast-forward here as I remove those two nuts and the three bolts.
To give yourself some more room, there's a little clip that holds the wiring harness. You just reach in back, pinch the tabs on the clip to pull it out, and that lets you move the wiring harness around and get the regulator a little more easily.
New regulator from 1A Auto, it's going to mount in the same. There are a couple of minor differences. The motor mounts with nuts instead of bolts, and the motor has a pigtail on it. It's going to connect the same. It's going to be in a little different place.
First, I'm just going to take these three nuts off. We put the regulator and motor back in just the same. Your regulator over there, bring this over, and mounts there. Once you have the regulator in place, just use the three nuts and start them onto the studs for the window motor, and then tighten them up, and you want to tighten them up nice and snug. You don't need to over tighten them, though. Also, while you're here, you can reconnect the window motor lead and then put the two nuts back on the regulator rails and tighten those up as well.
Now, you want to put the nose in, just make sure you guide it around the regulator here. Make sure the back and the front are in the track. It goes up and down nice and easy. Slide it down through the regulator. I'm plugging my panel back and I've got the key on. I'm just going to run my window up a little bit until I get to this hole right here. I'm just going to fast-forward here as I insert that second bolt and tighten it up.
With everything hooked up now, I'll do a quick test. It works pretty good. Disconnect this. Put my weather strip back on. Connect that. Then carefully put your water shield back in place. Look at some of the holes where the screws go, and the guide pins on the door panel just to make sure that it's lined up well. You don't want to block off the screw holes. First, reconnect your harness. Hook the top up and over the weather strip here. Look back in here, make sure the pins are going into the holes. Fast-forward as I put the bezel on, and then the screws. The natural colored screw goes behind the door handle. The skinny diameter black screw goes in the back, and then the two larger black screws go in the door pull and the front of the door panel. Then, to finish up, make sure you just close the little trapdoor in behind the door handle and put that front button trim back on.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
