Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Rear Sway Bar Link 1998-2007 Honda Accord
Created on:
Tools used
5mm Hex Wrench
14mm Wrench
Socket Extensions
Torque Wrench
14mm Socket
15mm Socket
19mm Socket
Ratchet
1/2 Inch Breaker Bar
1. Removing the Wheel
Loosen the 19mm lug nuts with the vehicle on the ground
Raise the vehicle with a floor jack
Secure the vehicle on jack stands
Remove the lug nuts
Pull off the wheel
2. Removing the Rear Sway Bar Link
Break the nuts free with a 14mm wrench
Counter-hold with a 5mm Allen bit
Remove the upper nut with a 14mm wrench
If necessary, secure the backside of the upper nut with locking pliers
Remove the nut with a 14mm socket, ratchet, and socket extension
Counter-hold with a 5mm Allen key
Remove the lower nut with a 14mm wrench
If necessary, secure the backside of the upper nut with locking pliers
Remove the nut with a 14mm socket, ratchet, and socket extension
3. Installing the Rear Sway Bar Link
Insert the sway bar link into place
Secure the nuts with a 14mm wrench (bottom nut first) and tighten with a 15mm socket and ratchet
Torque the bolts to 29 foot-pounds
4. Reattaching the Wheel
Slide the wheel into place
Start the lug nuts by hand
Tighten the lug nuts preliminarily
Lower the vehicle to the ground
Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern
Hi. I'm Mike from 1A Auto. We've been selling auto parts for over 30 years.
Hey, everyone. Sue here from 1A Auto. And today on our 07 Honda Accord we have in the shop, we're going to do rear sway bar links. If you need those parts or any other parts for your car, click on the link below and head on over to 1aauto.com.
19 millimeter socket to loosen up the lug nuts. I'm going to use a two post lift to raise my vehicle. You can use a jack and jack stands at home. Now I can take my 19 millimeter socket, now that I've raised it up, I can remove the lug nuts to take the tire off.
Rear sway bar links, 14 millimeter wrench. I'm going to place that on the top link on the nut. My nut, and it's a five millimeter Allen head socket that goes right in the center of it. I'm just going to give it a little tap right in there. I pre-sprayed but I'm going to spray again cause of the weathering element. See if I can make sure there's no rust sticking there. Okay now I'm going to put my ratchet on there.
Let's see if we made enough room that we can actually put a pair of locking pliers in the back there. And then we'll use a socket. Now I have a pair of needle nose locking pliers and there's a metal lip, washer flat side on the other side. Once I loosen it up enough, I can grab it with these and lock this down. Now I can put a socket on there. And that's just the top. Got the bottom to go.
Okay the lower sway bar link, we're going to do the same thing. Just have a little bit more room to work with. I'm going to put the locking pliers on there. 14 millimeter socket. Marvelous, look at that.
Here we have our brand new sway bar link from 1A Auto, and here I have the manufacturer's one I just took off our 07 Honda Accord. It's still the original equipment by the looks of it and you can see their design. They put the Allen head and a little flat washer there. With a 1A one, puts a space for our open end wrench and the new nuts. They're both sealed units, non-greasable. If you need this part or any other part for your car, click on the link below and head on over to 1aauto.com.
Now we're going to reinstall our new rear wheel sway bar links and we're going to install the one of the bar first. Start the nut. Now we have the freedom of moving it back and forth, nut down. The inside bolt hex is a 14 millimeter open end wrench, and the outside is a 15 mm. So 14 mm on the inside, that open-end wrench. And 15 mm socket. I'm just going to snug them because the torque specs is 29 foot pounds. So I'll snug that one and now I'll get to this one.
So I'm going to torque them now to 29 foot-pounds. Now we're just going to repeat the process on the other side. 19 millimeter socket. We're going to torque the wheels up. The wheel torque on this particular model is 80 foot pounds. Make sure you do it in the star pattern, criss-cross and then double check.
Thanks for watching. Visit us at 1aauto.com for quality auto parts, fast and free shipping and the best customer service in the industry.
PSA67875
In Stock
Product Reviews
Loading reviews
There are no reviews for this item.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.