Genuine original equipment part (OEM) that was factory installed on your vehicle by the manufacturer.
Left Hand Drive:
All of our auto parts are intended for Left Hand Drive USDM vehicles. If your vehicle is Right Hand Drive, please ensure the part is correct for your specific vehicle.
Item Condition:New
Attention California Customers:
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1 Year Warranty
This item is backed by our 1-year warranty. In the event this item should fail during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Blower Motor Resistor 1994-2008 Dodge Ram
How to Replace Blower Motor Resistor 1994-2008 Dodge Ram
Created on:
Tools used
Phillips Head Screwdriver
1. Removing the Blower Motor Resistor
Locate the resistor under the glove box on the HVAC box
Disconnect the wiring harness
Remove the two Phillips screws from the resistor
Remove the resistor
2. Installing the Blower Motor Resistor
Insert the blower resistor into place
Tighten the two Phillips screws to the resistor
Connect the wiring harness
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the blower motor resistor in this Dodge Ram. This one is a 2008, but this procedure is similar for 1994 to 2009 Dodge Rams. You'll need a new resistor from 1AAuto.com and a Phillips screwdriver.
Your blower motor resister is located under the dashboard on the passenger side, just below the glove box. We'll disconnect the electrical connector and remove these two number two Phillips head screws. Remove the resistor from the bottom of the HVAC box.
Here we have our old part that we removed from the vehicle and our new part from 1A Auto. As you can see, they're identical. We have this ceramic heat sync on the part of the resistor here. Same four pin connection at the bottom, as well as the same two bolt holes. You'll see that ours has become overheated. You can see that this ceramic is cracking. We actually have a good chunk of it that's come off here. This is a good sign that our resistor is getting too hot, possibly because of all this corrosion build up on the copper terminals at the bottom. If these go bad, it can cause operation of certain fan speeds or the fan to fail completely, so be sure to check out this resistor before you go and replace a fan.
Install the new blower motor resistor into the bottom of the HVAC box. Start your two Phillips head screws. Tighten them down with your number two Phillips head screwdriver. Reconnect your electrical connector.
Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.
Tools used
Phillips Head Screwdriver
1. Remove the AC Heater Fan Speed Control Resistor
Disconnect the wiring harness.
Remove the two Phillips screws securing the resistor.
2. Install the new AC Heater Fan Speed Control Resistor
Secure the resistor with your Phillips screwdriver.
Plug in the wiring harness.
Brought to you by 1AAuto.com. Your source for quality replacement parts and the best service on the internet. In this video, we're going to show you the location and how to replace your blower motor resistor. If your truck, the fan works, but maybe it doesn't work on certain fan settings like low or second, that's usually that your resistor's gone bad.
A pretty easy replacement. Just need a Phillips screwdriver. Your blower resistor, you can see it right here, along with two Phillips screws. It's pretty easy to access, although I'm going to film from right down here. Now first, there's a tab on the inside of the harness. Push the tab in and work that down. Then there are two screws. Original, new one from 1A Auto. You can see pretty much all the same. The connection is exactly the same. It's going to go in, both in, and function just like the original. Now install our new one up in there. Reconnect the lead. Turn the key on. Blow, two, three, four.
We hope this helps you out. Brought to you by www.1AAuto.com. Your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free: 888-844-3393. We're the company that's here for you on the internet and in person.
4720278
In Stock
Product Reviews
Loading reviews
5.00/ 5.02
2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
0
0
0
0
Great part
William
February 18, 2021
Fit well easy to installWrite your review here. It must be at least 50 characters long. Consider whether you would recommend this product and what you like or dislike about it.
Jose
July 23, 2021
Easy order. Good price. Exact fit.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Jeep is a registered trademark of FCA US LLC. 1A Auto is not affiliated with or sponsored by Jeep or FCA US LLC.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.