2007 Jeep Commander V8 4.7L Starter TRQ STA03084

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace a starter on this 2006 Jeep Liberty. The items you'll need for this is a flat blade screwdriver; an 8 millimeter, 10 millimeter, 13 millimeter and 15 millimeter socket and ratchet; 15 millimeter wrench; a hammer; and jack and jack stands. It's not required, but it does help to have a second person help you out on this.

Start off using a 12 millimeter socket and ratchet and disconnect your negative battery cable.

Your starter is located right here. You want to start off by removing the lower bolt on the heat shield connected to your starter. It's going to be 10 millimeters. Now you just, for now, push that heat shield up and out of the way. Now you have access to these harnesses. On the yellow one, just push the tab on the clip and pull it free. For this red one, it's held on with a 13 millimeter nut. We'll just fast forward as Don removes that nut and then pulls the wire off the stud.

You'll need to remove your front drive shaft to get some clearance. It's held in by a bunch of 8 millimeter bolts. You'll either want somebody to hold it or put your transfer case in four wheel drive and hold the brakes in order to hold those bolts and then just loosen them up one at a time. Loosen the front first and then the rear. Using your hammer and a flat blade screwdriver, break that front part free. We'll just fast forward as Don removes the 8 millimeter bolts on the other side. It helps to have another person holding the drive shaft wile someone else removes the bolts but you can brace it yourself. Now again, use a hammer and a flat blade screwdriver and break this in free. Then you just pull this down and out.

Now, on this bracket right here, you'll see there's two 15 millimeter bolts. You want to go ahead and remove both of those. Pull that bracket back and out of the way. This gives you access to the two 15 millimeter bolts on the starter. For the top one, you can see we used a piece of pipe for some extra leverage to break it free. Then, using a regular socket and ratchet, we removed it most of the way. Once we got to a certain point, the ratchet didn't fit anymore so we had to go 15 millimeter wrench. For the lower one, it's just as simple as using a 15 millimeter socket and ratchet. Once you've removed those bolts, turn your starter so you have better access to this 10 millimeter bolt holding on your heat shield. Just remove that real quick. Once it's removed, pull your heat shield down and off. Then you can pull your starter out.

Now, feed your new starter up into place and replace your heat shield and the 10 millimeter bolt you removed last. We'll just fast-forward as he tightens that up. Now, put your starter into place. Replace those two 15 millimeter bolts. We're going to fast forward as he replaces both of them and tightens them up. You can see he's going to use a wrench for the top one. You want to make sure that these are nice and tight. Now, push that red wire back onto the stud and replace that 13 millimeter nut and tighten that up. Push the yellow wire back into place and push your heat shield down. Replace that 10 millimeter bolt. Tighten that up and then push your bracket back into place and replace those two 15 millimeter bolts.

Now, feed your drive shaft back up into place. You want to feed the back end of it in first and fit it up and over where it's supposed to go. Push the front end of the drive shaft back into place and lower the back end down where it needs to be. Now, you just want to replace those 8 millimeter bolts. We'll just fast forward as Don does this. You want to stop the wheel from moving so this won't turn so you can tighten the bolts up. Having a second person to hold the wheel or bracing it some other way just so it can't move. You want to repeat the process on the other end. Again, we'll just fast forward as Don replaces those 8 millimeter bolts. Torque those to 12 to 14 foot-pounds.

Reconnect your negative batter cable and make sure you tighten it up.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.