WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How To Replace Purge Valve Solenoid 2006-08 Mazda 6
Created on:
Tools used
Needle nose pliers
1. Removing the Purge Valve Solenoid
Loosen the hose clamps on the solenoid
Disconnect the hose from the solenoid
Disconnect the sensor connector
Remove the mounting rubber
2. Installing the Purge Valve Solenoid
Connect the wiring harness
Slide the rubber bracket onto the steel mounting bracket
Attach the hoses to the solenoid
Tighten the hose clamps
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
Hi everyone. Sue at 1A Auto here. Today we're going to install the purge valve solenoid. And that's located up here in the engine compartment. So if you need this part, or any other part for your car, click on the link in the description and head on over to 1AAuto.com.
I'm going to undo both these clamps with a pair of just needle-nose pliers. One there. One in the back. Slide them off the hose. I'm just going to use them to pry the hose off. There's the one in the back and one in the front. Now you can see the connector. And this is mounted on a rubber bushing that comes right there. You see that? Comes with the sensor. And that just manipulates out of there. I'll just take the sensor off of it, and we'll get it out of there.
So here's the sensor, and there's the connector tab, going to push down on that. And there's your purge valve solenoid. Now with the sensor out of the way, it's easier for me to just pull that rubber right out of the way. Because the new sensor comes with a new mounting rubber.
Here we have our new sensor from 1AAuto.com and the OE factory one that we just took out of our '07 Mazda. They are the same height, diameter, and two inlets. Inlet and outlet of hose. Same diameter. Two wire connector, and the new one comes with a new rubber mount. So if you need this part, or any other part for your car, click on the link below, and head on over to 1AAuto.com.
Basically, we're going to reverse procedure here to reconnect. I'm going to connect the connector first before I put the rubber mount on that bushing. So the tab was on the bottom. Line those up. Push it in ‘til it clicks. Now, you see the slotted on the rubber mount. That's going to go right onto this ear, on the steel bracket. If you need to, you can put a little spray on there to help it on, but there it is. It's on. We can mount the back hose. And put the front hose on. All this time, I did inspect the hoses to make sure there's no tears or cracks and no dry rot. And we'll just remount the clamps. Okay. There you go. Your evap solenoid sensor's hooked up. And you're ready to go.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
911-702
In Stock
Product Reviews
Loading reviews
There are no reviews for this item.
Customer Q&A
Can you show me where this part is located on the v6 3.0 motor for the 2004 Mazda 6 ?November 24, 2021
Ryan O
10
It is located next to the throttle body on a little bracket attached to the air intake hose.
November 26, 2021
Andra M
Will this fit on a Mazdaspeed 6 or is it just a regular 6?August 28, 2022
John D
10
This part will fit on the 2006 Mazda 6 mazdaspeed 2.3L engine.
August 29, 2022
Andra M
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Mazda is a registered trademark of Mazda Motor Corporation. 1A Auto is not affiliated with or sponsored by Mazda or Mazda Motor Corporation.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.