Replaces
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video we show you how to replace or service the side marker on this 2004 Volvo XC90. We show you both if you just need to replace the little bulb inside that light, or if you need to replace the entire light if it's been broken or something like that. The only tool you'll need is a small flat blade screwdriver.
On this little side marker here, actually right in the middle there, is a little indent. You put a screwdriver up in there. This one actually comes out very easily, and I can see why it's already been broken off. It's generally right in underneath the bulb, you'll feel it right there, and you pry it out, and then this comes out.
If you're just looking to change the bulb, you twist counterclockwise. You need this orange bulb, it just pulls out of the socket. That goes back in. Put the light back on. To disconnect the harness, there's just a little thumb tab over here, and that comes out.
Here's a new light from 1A Auto. Obviously if yours has been broken, this will fix your problem. Just reconnects right in and snaps right into place.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a side marker light on this 2002 Volvo V70. Tools you'll need if you have to do the whole project: new side marker light from 1AAuto.com, drill with quarter-inch drill bit, hammer, punch, rivet gun.
Most likely, your side marker light has been damaged, so you will be able to skip the part where you have to drill the rivets and instead use some force (either some pliers or a screwdriver) to pry the old light out and then put the new light from 1A Auto in.
If you're just looking to service the bulb, and you need to get the light out, and there's no damage to the light itself, you'll need to remove these three rivets. You remove them by drilling the center with your drill and quarter-inch drill bit. On the back of the light, there's two tabs that you have to push in and then push the light out. Reach in behind your inner fender, push those tabs, and the light pushes out. Then push the tab on the harness and disconnect it.
To service the light, you just twist out the socket, pull the bulb out, push your new bulb in, and twist the socket back into place. On the left is the old side marker light; on the right is the new one from 1A Auto. You can see they're identical, and they're going to fit exactly the same. Reconnect the harness to your new side marker light, and then just push the light back into place.
Using a hammer and a punch, just punch out those rivets. If you did remove the rivets from your wheel well, re-secure them. Here, we're showing you a rivet and rivet gun. You could also use coarse-thread bolts in the place of the rivets.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
