Kit Includes: (2) Front Outer Tie Rods (1) Rack & Pinion Assembly
Specification
Side Location
Driver & Passenger Side
Location
Front
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Application Specific Design: No modifications necessary
Anti-Corrosion Coated: Enhanced surface life
Pre-greased: No additional maintenance required
Kitted for Restored Performance: Improved road-feel and handling
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
How to Replace Outer Tie Rod 2005-10 Pontiac G6
How to Replace Outer Tie Rod 2007-2009 Saturn Aura
How to Replace Outer Tie Rod 2005-2010 Pontiac G6
How to Replace Steering Rack Pinion 2005-2010 Pontiac G6
How to Replace Outer Tie Rod Ends 2008-12 Chevy Malibu
Created on:
Tools used
Adjustable Wrench
Measuring Tape
Hammer
Torque Wrench
18mm Wrench
13/16 Inch Wrench
Jack Stands
18mm Socket
19mm Socket
Ratchet
Floor Jack
1. Removing the Wheel
Loosen the lug nut covers with a 19mm socket
Pry off the center cap with a flat blade screwdriver
Loosen the lug nuts with the vehicle on the ground
Raise the vehicle with a floor jack
Secure the vehicle on jack stands
Remove the lug nuts
Pull off the wheel
2. Removing the Outer Tie Rod
Measure the distance from the boot of the inner tie rod to the edge of the outer tie rod
Make note of this measurement
Loosen the nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
Remove the 18mm nut from the outer tie rod end
Loosen the nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
Strike the steering knuckle with a hammer to loosen the outer tie rod
Pull the outer tie rod out of the steering knuckle
Twist off the outer tie rod by hand
3. Installing the New Outer Tie Rod
Twist the new outer tie rod onto the inner tie rod
Push the outer tie rod into the steering knuckle
Place vise grip pliers to hold the other part of the ball joint
Fasten the 18mm nut onto the outer tie rod with a socket
Place the pliers on the bottom of the bolt
Tighten the nut with an 18mm wrench
Tighten the nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
Measure the distance from the boot of the inner tie rod to the edge of the outer tie rod
This should be the same as the measurement noted in Step 2
4. Reattaching the Wheel
Slide the wheel into place
Start the lug nuts by hand
Tighten the lug nuts preliminarily
Lower the vehicle to the ground
Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
Reattach the center cap
Tighten the lug nut covers with a 19mm socket
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an outer tire rod on this 2007 Pontiac G6. It's pretty much the same as any 2005 to 2010 G6, as well as a Saturn Aura. We show you the right-hand or passenger side, but the left-hand driver side is the same procedure. You'll need a new tie rod or tie rods from www.1AAuto.com, jack and jack stands, 18mm and 19mm sockets with a socket wrench, maybe even a breaker bar or a pipe for leverage, tape measure, 18mm wrench, large adjustable or a 13/16 wrench, hammer, and a torque wrench.
Depending on what wheels you have, start out be removing the lug caps, and then we'll cover if applicable. Then, if you don't have the benefit of air tools, you're going to want to loosen the lug nuts with the vehicle on the ground. Then raise and support the vehicle. I'll remove the lug nuts, wheel, and tire.
Use a tape measure to get a general idea of a total length. You can use a reference point of the outer part of the boot, and then the outer part of the tie rod end, and just remember that number. On the end of the tie rod is an 18mm, so I'm using the socket and socket wrench to remove that nut. I'll fast-forward as I take off that nut.
Locate the nut at the end of the outer tire rod. We're going to go ahead and just loosen it just a little bit. I'm using a 13/16 wrench. You can use the metric equivalent. With a hammer, go ahead and give the end of that spindle a whack and pull the outer tie rod out. Then you can go ahead and unscrew it. I'll fast-forward through that. Be as careful as you can to not turn the inner tie rod.
Here, we're going to reinstall. You'll notice we are reinstalling the old one. There's nothing wrong with the tie rods on this vehicle. We just are doing this to show you how to do it. Tie rods from 1A Auto are going to be an exact match to the original. You may want to just measure the length. There could be a slight difference in length, and you would want to make sure you align it well.
Go ahead and put that 18mm nut back on the outer tire rod. I'm using a small pair of vice grips to hold the other part of the ball joint so that it doesn't spin as I tighten up that 18mm nut. There might be other ways that you would find easier to do it, but that's the one that I use. Then once I get it through, I'll be able to put the vice grip on the end that's coming through the nut. You can see here that once I take that socket off, I'll have plenty of room to put that on, and then use an open-ended wrench.
Here, I'm using that vice grip on the bottom, and I'm going to use an open-ended wrench to finish up tightening it up. I'll fast-forward through this. Now tighten up the nut on the inner tie rod that we just slightly loosened. Make sure that's snug up against the back portion of that outer tie rod. I'm just verifying that the tire rod is in somewhat of a right position, and it will be ready for me to take over to have an alignment done.
Install the wheel, and tighten up on your lug nuts. I'll go ahead and fast-forward through this. In a star pattern, go ahead and torque your lug nuts to roughly 100 foot-pounds. Reinstall your hubcap, and make sure that you line up the notch in the hubcap for where your valve stem is. Then, by hand, use your 19mm socket to tighten up those plastic lug nut covers. I'll fast-forward through that.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
21mm wrench
Side Cutters
Torque Wrench
Hammer
18mm Socket
19mm Socket
Anti-Seize Grease
1/2 Inch Impact Gun
Tools used
21mm wrench
Torque Wrench
Hammer
18mm Socket
19mm Socket
Anti-Seize Grease
1/2 Inch Impact Gun
Tools used
Torque Wrench
Hammer
18mm Wrench
Pry Bar
18mm Socket
19mm Socket
21mm wrench
Locking Pliers
Bungee Cord
Anti-Seize Grease
Ratchet
3/8 Inch Impact Gun
1/2 Inch Impact Gun
11mm Socket
Tools used
Torque Wrench
Gloves
Hammer
Rust Penetrant
Copper Anti-Seize
19mm Socket
Cotter Pin
Torque Angle Gauge
Safety Glasses
Pliers
1/2 Inch Impact Gun
Marker / Writing Utensil
Okay friends. Before we get started, the first thing that I want to mention is you want to be safe, so have hand protection and eye protection. The next thing we're gonna talk about is safely raising and supporting the vehicle so the suspension is hanging. So come right underneath here, this is where you're gonna support the vehicle in the front. Now with the front of the vehicle, safely raised and supported. We're gonna remove all five of our 19-millimeter lug nuts.
Remove your wheel. Now that we have the wheel off, we have a clear view of our tie rod area, I'm just gonna spray down these areas with some penetrant spray. Now we're gonna use some nice long pliers, and I'm gonna break this jam nut free. Turn this clockwise. There we are. Now, we're gonna remove our outer tie rod end nut.
If you find that the outer tie rod end nut just spins the whole stud inside of the knuckle, you could take those nice long pliers or whatever you might happen to have, and just try to squeeze this down as tight as you can. We're gonna apply a little bit of pressure, and we'll try again. If your tie rod still stuck in the knuckle, it's great to use a hammer, bonk right on the knuckle right here, and break it free.
For the next part, we're gonna want something that you can write with, because we're gonna take off the tie rod, but as we turn it, and we make a complete rotation, we're gonna count those rotations and take note of it. That's one, two, three, and so on. It's always important to make sure you coat your threads with something such as copper never seize.
Now it's gonna be time to put on our brand new outer tie rod end. As you go to install it, make sure you put on the same amount of turns that you had to remove the old one. One, two, three, and so on. Should pretty much line up. Let's put on our outer tie rod end nut. We'll snug it up, and then we'll torque it to manufacturer specifications as well. We wanna torque this to 18 foot-pounds and then add an additional 90 degrees, so basically a quarter turn after the 18. So that's 18. Now I need to take it another quarter turn. I'm gonna start approximately like that, and I'm gonna bring it right out to me. There we are.
The next thing we wanna do is pay attention to the slots on the nut compared to the hole in the stud. If it doesn't line up, you need to continue tightening until it does. Go to the very next slot. As you can tell I have that lined up now. Take your cotter pin, slide it through, and then peen it over so there's no way this nut can loosen up on its own.
Now it's time to tighten up our jam nut. We're gonna grab this, turn it counterclockwise. That feels good. Now just go ahead and grab onto that tie rod, make sure it's pretty level and it's not kinked in any way. Double check everything. We have all our clamps. Perfect. We're gonna go ahead and put the wheel on here. We'll start all the lug nuts, we'll snug them up, and then we'll torque them to 100 foot pounds. Torqued.
The prices are great and you receive your items on time.
Customer Q&A
Does this kit fit a 2005 Malibu maxx Ls electric steering ?December 19, 2020
Randy R
10
Yes, this kit will be a direct fit for your 2005 Malibu Maxx.
December 19, 2020
Curtis L
Does this fit 05 malibu ls?March 25, 2022
John D
10
Yes, this part will fit your vehicle.
March 25, 2022
Andra M
Is this the right part for 2010 Chevy Malibu LS 2.4L engine ?November 23, 2022
Tawana- M
10
Yes, this part will fit your vehicle.
November 23, 2022
Jessica D
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Chevrolet is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by Chevrolet or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.